Navigation

    • Register
    • Login
    • Search
    • OpenHardware.io
    • Categories
    • Recent
    • Tags
    • Popular
    1. Home
    2. MGHaff
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    MGHaff

    @MGHaff

    6
    Reputation
    27
    Posts
    436
    Profile views
    0
    Followers
    1
    Following
    Joined Last Online
    Location USA Age 43

    MGHaff Follow

    Best posts made by MGHaff

    • RE: 2 dallas temp + 4 relays

      First of all. thank you guys for all the help! here is what i found out. When testing my hardware i found that alone with the MySensors Dallas sensors sketch i would get readings from my Dallas sensors in serial and at controller. With relay sketch alone i would get All 4 relays working in controller and in serial. But combined no Dallas temp in serial or controller. I rewired with new sensors, Arduino nano, radio! Finally digging through my stuff i found a new board from a batch ordered 2 years ago, wired it up on bread board and wallah! Apparently the last batch or boards i ordered must have not passed quality or damaged in shipping!! Thanks again for the support!! On a way brighter note I have address's assigned to my temp sensors now on all my nodes and have learned so much more about the MySensors network!

      posted in Troubleshooting
      MGHaff
      MGHaff
    • Newbie, adding more than one relay to nodemanager

      I just started using nodemanager. GREAT WORK! Might be a dumb question but how do i add more than one relay to the sketch? I would like to control 4 but only can get one to work. Thanks in advance!

      posted in NodeManager
      MGHaff
      MGHaff
    • RE: [SOLVED] Raspberry Pi serial gateway NRF24 - !TSM:INIT:TSP FAIL

      This is what i use to configure my raspberry pi3 to work vi serial.

      --my-transport=rf24 --my-rf24-pa-level=RF24_PA_LOW --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18

      Built using this page. https://www.mysensors.org/build/raspberry

      And when recieving this error "Dec 31 11:07:50 DEBUG !TSM:INIT:TSP FAIL" I had found a bad jumper that I had used. Hope This helps!

      posted in Troubleshooting
      MGHaff
      MGHaff
    • RE: Raspberry Pi Zero W gateway + NRF24L01+ Radio + MQTT - Radio failing

      In your configuration try leaving the "--my-controller-ip-address=127.0.0.1" out of configuration. Another thing to try is to power the radio connected to the pi by a separate 3.3v power supply. also when i built my first controller/gateway i spent 2 days trying to figure out why it didn't work when in the end it was a bad jumper wire. Unhook everything and double check your wiring. Hope something helps! 🙂

      posted in Troubleshooting
      MGHaff
      MGHaff

    Latest posts made by MGHaff

    • RE: Raspberry Pi Zero W gateway + NRF24L01+ Radio + MQTT - Radio failing

      In your configuration try leaving the "--my-controller-ip-address=127.0.0.1" out of configuration. Another thing to try is to power the radio connected to the pi by a separate 3.3v power supply. also when i built my first controller/gateway i spent 2 days trying to figure out why it didn't work when in the end it was a bad jumper wire. Unhook everything and double check your wiring. Hope something helps! 🙂

      posted in Troubleshooting
      MGHaff
      MGHaff
    • RE: edited: 4 diy dimmer module. should i make icsp or serial programming connections, both?

      Thanks, I guess what i am trying to find out is how i get my sensors code to use the Adafruit_PWMServoDriver code to do the same as you than. I would like to control 5 sets of RGB strips by 5 separate V_RGB faders in domoticz using my sensors. But i cant figure out how to get mysensors to tell the PCA9685 chip how to controll the channels.

      posted in Hardware
      MGHaff
      MGHaff
    • RE: edited: 4 diy dimmer module. should i make icsp or serial programming connections, both?

      @joerideman what code are you using to run the 9685 chip? I'm looking to build a multi rgb strip controller but having problems finding mysensors code to use as an example to talk to the 9685. Any help is greatly appreciated! thanks.

      posted in Hardware
      MGHaff
      MGHaff
    • RE: Newbie, adding more than one relay to nodemanager

      @user2684 said in Newbie, adding more than one relay to nodemanager:

      relay1.setInvertValueToWrite(true);
      relay2.setInvertValueToWrite(true);

      WOW Thanks Again! This is really fun and easy to work with! Thank you!!!!

      posted in NodeManager
      MGHaff
      MGHaff
    • RE: [SOLVED] Raspberry Pi serial gateway NRF24 - !TSM:INIT:TSP FAIL

      @badisensors I did try your config and it works just as mine does. Just wondering if the adding this --my-rf24-ce-pin=22 --my-rf24-cs-pin=24 to the config was necessary. But from the my test it is not. Thanks.

      posted in Troubleshooting
      MGHaff
      MGHaff
    • RE: Newbie, adding more than one relay to nodemanager

      @user2684 Another Question.... Thanks in advance!
      Where do i put this to get my relay to invert operation?
      // [109] Invert the value to write. E.g. if ON is received, write LOW (default: false)
      void setInvertValueToWrite(bool value);

      And how should it be written.

      I tried this.
      #include <sensors/SensorRelay.h>
      SensorRelay relay1(8);
      SensorRelay relay2(5);
      SensorRelay relay3(6);
      SensorRelay relay4(7);
      // [109] Invert the value to write. E.g. if ON is received, write LOW (default: false)
      SensorRelay setInvertValueToWrite(true);

      posted in NodeManager
      MGHaff
      MGHaff
    • RE: Newbie, adding more than one relay to nodemanager

      @user2684 Perfect Thanks!

      posted in NodeManager
      MGHaff
      MGHaff
    • RE: [SOLVED] Raspberry Pi serial gateway NRF24 - !TSM:INIT:TSP FAIL

      @badisensors 2.0.0 not really 2 years ago more like 1 1/2. Why do you ask?

      posted in Troubleshooting
      MGHaff
      MGHaff