Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 MDMSPanel "Nextion"

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/676/MDMSPanel-Nextion
Reply Quote 1
1 Reply Last reply
sebdetours last edited by

Hello Kalina.

Really good job. I like the way you designed your products. (not only this one

A question about the Box. Did you take a standart case that you cut out, or did you have your own case made from a manufacturer?

Regards
Reply Quote 0
1 Reply Last reply
kalina Hardware Contributor last edited by @sebdetours

@sebdetours said in MDMSPanel "Nextion":

Did you take a standart case that you cut out?

Hi @sebdetours, yes. This is G1910 (Gainta) box. See drawing attached to projet files.
Reply Quote 0
1 Reply Last reply

arduino 119 rtc 5 atmega 3 modbus 3 display 3 nextion 3 st485 2 jtag 2 megacore 1

3
Posts

749
Views

Log in to reply

Suggested Topics

💬 Arduino UNO NRF24L01+ Shield V1.3
OpenHardware.io • arduino nrf24l01 nrf24l01+ shield arduino uno • • openhardware.io

1

0
Votes

1
Posts

123
Views

No one has replied
💬 MySensors Linky
OpenHardware.io • mysensors arduino mysensor arduino pro mini linky edf enedis • • openhardware.io

12

0
Votes

12
Posts

579
Views

thanks for you reply Fumée Bleue.
💬 ESP WaterMeter
OpenHardware.io • arduino esp8266 domoticz esp fumée bleue jeedom • • openhardware.io

1

0
Votes

1
Posts

38
Views

No one has replied
How to check if serial gateway is operational ?
Development • arduino serial gateway • • joshmosh

4

0
Votes

4
Posts

2214
Views

@fot said: Hi! I ask my gateway about it's version (0;0;3;0;2;). It will responde with the library version number (1.4.1 in my case). It tells me that the gateway software is up and running. But it will not give me any clue about if the (NRF)network is working. That's a problem, right. I only ask the gateway if no other packages are received in $timeout seconds. /Magnus Of course ! Thank you for pushing my nose on it. Sometimes you don't see the most obvious Since my gateway is relatively close to the controller (Domoticz on a Raspi), I can do a hard reset of the gateway (via Raspi GPIO), which should resolve the issue. Cheers Josh
Capacitive sensor w/ transceiver
Development • arduino nrf24l01+ capacitive touc • • Conan

4

0
Votes

4
Posts

1872
Views

@BulldogLowell I just realized you hyperlinked the command. Disregard my previous message.
💬 MDMSNode "Lighting" Rev 1.1
OpenHardware.io • mysensors arduino nrf24l01 atsha204a ota atmega328p rfm69hw hlk-pm01 lighting triac • • openhardware.io

9

0
Votes

9
Posts

2608
Views

@kalina, Thanks. So it will not work for my configuration. Wall switch (push button) is already installed. No possibilities to draw more electrical wires. Moreover, if i put the board near the light, i have just the Neutral and the return wire from the wall switch. No Live wire to power on the mysensors board. I think in my ase the best way is to manage everything in my garage in the electrical main board where all the wires are mapped. I can get L + N for mysensors power supply. And i can continue to reuse the original wall switch independently of the Mysensors board.
💬 Valden: Heat Pump Controller
OpenHardware.io • arduino power diy thermostat heating gerber refrigerant refrigeration compressor rs-485 green-energy heat-pump eev txv cappilary heat-exchange • • openhardware.io

1

0
Votes

1
Posts

18
Views

No one has replied

20
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1