Adafruit RFM69 Bonnet not working

[mfalkvidd]

Welcome to the forum @paulsp

The log parser can help understanding the log output.

Your node fails to initialize because it thinks it has been assigned node id 0 (which is reserved for the gateway). Run the MySensors cleareeprom sketch and then upload your existing sketch again.

[paulsp]

@mfalkvidd Running the cleareeprom sketch on the M0 Express did not work.

1385 MCO:BGN:INIT NODE,CP=RPNNS---,FQ=48,REL=255,VER=2.3.2
6370 TSM:INIT
8022 TSF:WUR:MS=0
8022 THA:INIT
8022 RFM69:INIT
8027 RFM69:INIT:PIN,CS=10,IQP=6,IQN=6,RST=11
8029 RFM69:PTX:LEVEL=5 dBm
8029 TSM:INIT:TSP OK
8029 !TSF:SID:FAIL,ID=0
8029 TSM:FAIL:CNT=1
8029 TSM:FAIL:DIS
8029 TSF:TDI:TSL
8029 RFM69:RSL
18030 TSM:FAIL:RE-INIT
18030 TSM:INIT
19367 THA:INIT
19367 RFM69:INIT
19372 RFM69:INIT:PIN,CS=10,IQP=6,IQN=6,RST=11
19373 RFM69:PTX:LEVEL=5 dBm
19373 TSM:INIT:TSP OK
19373 !TSF:SID:FAIL,ID=0
19374 TSM:FAIL:CNT=2
19374 TSM:FAIL:DIS
19374 TSF:TDI:TSL
19374 RFM69:RSL
29375 TSM:FAIL:RE-INIT

How can I determine the gateway running the PI is receiving a request from the M0 and then replying to the M0?

[mfalkvidd]

@paulsp said in Adafruit RFM69 Bonnet not working:

How can I determine the gateway running the PI is receiving a request from the M0 and then replying to the M0?

As long as the M0 thinks it has Id 0, it will not communicate.

Could you post the sketch for the M0?

If the MySensors cleareeprom sketch did not work, it seems like the eeprom in the M0 is broken. Could you share the output from the MySensors cleareeprom run? It should look like this:

Started clearing. Please wait...
Clearing done.

[paulsp]

Below is the atc_signalsreport sketch modified to support the pin number and Serial configuration of the M0. I also include the ClearEepromConfig sketch modified to display the value of EEPROM_LOCAL_CONFIG_ADDRESS
Output of the sketch

Started clearing. Please wait...
413
Clearing done.

Modified atc_signalsreport sketch

/*
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2019 Sensnology AB
 * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - tekka
 *
 * DESCRIPTION
 * ATC mode settings and signal report functions, on RFM69 and RFM95 nodes
 *
 */
#define MY_SERIALDEVICE Serial

// Enable debug prints
#define MY_DEBUG
#define MY_DEBUG_VERBOSE_TRANSPORT
#define MY_DEBUG_VERBOSE_TRANSPORT_HAL
#define MY_DEBUG_VERBOSE_RFM69

// Enable and select radio type attached

// RFM69
#define MY_RADIO_RFM69
#define MY_RFM69_NEW_DRIVER   // ATC on RFM69 works only with the new driver (not compatible with old=default driver)
#define MY_RFM69_ATC_TARGET_RSSI_DBM (-70)  // target RSSI -70dBm
#define MY_RFM69_MAX_POWER_LEVEL_DBM (10)   // max. TX power 10dBm = 10mW
#define MY_RFM69_CS_PIN 10
#define MY_RFM69_IRQ_PIN 6
#define MY_RFM69_RST_PIN 11

// RFM95
//#define MY_RADIO_RFM95
//#define MY_RFM95_ATC_TARGET_RSSI_DBM (-70)  // target RSSI -70dBm
//#define MY_RFM95_MAX_POWER_LEVEL_DBM (10)   // max. TX power 10dBm = 10mW

#include <MySensors.h>

// ID of the sensor child
#define CHILD_ID_UPLINK_QUALITY (0)
#define CHILD_ID_TX_LEVEL       (1)
#define CHILD_ID_TX_PERCENT     (2)
#define CHILD_ID_TX_RSSI        (3)
#define CHILD_ID_RX_RSSI        (4)
#define CHILD_ID_TX_SNR         (5)
#define CHILD_ID_RX_SNR         (6)


// Initialize general message
MyMessage msgTxRSSI(CHILD_ID_TX_RSSI, V_CUSTOM);
MyMessage msgRxRSSI(CHILD_ID_RX_RSSI, V_CUSTOM);
MyMessage msgTxSNR(CHILD_ID_TX_SNR, V_CUSTOM);
MyMessage msgRxSNR(CHILD_ID_RX_SNR, V_CUSTOM);
MyMessage msgTxLevel(CHILD_ID_TX_LEVEL, V_CUSTOM);
MyMessage msgTxPercent(CHILD_ID_TX_PERCENT, V_CUSTOM);
MyMessage msgUplinkQuality(CHILD_ID_UPLINK_QUALITY, V_CUSTOM);

void setup()
{
}


void presentation()
{
  // Send the sketch version information to the gateway and controller
  sendSketchInfo("ATC", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID_UPLINK_QUALITY, S_CUSTOM, "UPLINK QUALITY RSSI");
  present(CHILD_ID_TX_LEVEL, S_CUSTOM, "TX LEVEL DBM");
  present(CHILD_ID_TX_PERCENT, S_CUSTOM, "TX LEVEL PERCENT");
  present(CHILD_ID_TX_RSSI, S_CUSTOM, "TX RSSI");
  present(CHILD_ID_RX_RSSI, S_CUSTOM, "RX RSSI");
  present(CHILD_ID_TX_SNR, S_CUSTOM, "TX SNR");
  present(CHILD_ID_RX_SNR, S_CUSTOM, "RX SNR");
}

void loop()
{
  // send messages to GW
  send(msgUplinkQuality.set(transportGetSignalReport(SR_UPLINK_QUALITY)));
  send(msgTxLevel.set(transportGetSignalReport(SR_TX_POWER_LEVEL)));
  send(msgTxPercent.set(transportGetSignalReport(SR_TX_POWER_PERCENT)));
  // retrieve RSSI / SNR reports from incoming ACK
  send(msgTxRSSI.set(transportGetSignalReport(SR_TX_RSSI)));
  send(msgRxRSSI.set(transportGetSignalReport(SR_RX_RSSI)));
  send(msgTxSNR.set(transportGetSignalReport(SR_TX_SNR)));
  send(msgRxSNR.set(transportGetSignalReport(SR_RX_SNR)));
  // wait a bit
  wait(5000);
}

ClearEepromConfig sketch

/*
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2019 Sensnology AB
 * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * This sketch clears radioId, relayId and other routing information in EEPROM back to factory default
 *
 */
// load core modules only
#define MY_CORE_ONLY
#define MY_SERIALDEVICE Serial

#include <MySensors.h>

void setup()
{
	Serial.begin(MY_BAUD_RATE);
	Serial.println("Started clearing. Please wait...");
  Serial.println(EEPROM_LOCAL_CONFIG_ADDRESS);
	for (uint16_t i=0; i<EEPROM_LOCAL_CONFIG_ADDRESS; i++) {
		hwWriteConfig(i,0xFF);
	}
	Serial.println("Clearing done.");
}

void loop()
{
	// Nothing to do here...
}

[mfalkvidd]

Thanks @paulsp. I am out of ideas unfortunately. I can't understand why the M0 thinks it has node id 0.

[paulsp]

@mfalkvidd How can I hard code and ID for the device and the Gateway ID?

[mfalkvidd]

@paulsp gateway ID is always 0. It can not be changed.

To set an ID for the M0, add

#define MY_NODE_ID (42)

to the sketch, before including MySensors.h. Change 42 to whatever node ID you want to use (1-254).

https://www.mysensors.org/apidocs/group__RoutingNodeSettingGrpPub.html#gac677233da7f20bbf93cb479471e3234e

[Lucky65]

@paulsp I'm trying to get a Raspberry Pi gateway working as well. Also with a Bonnet but I don't think that is particularly pertinent as the bonnet doesn't do much other than connecting the RFM69 to a bunch of GPIO.
Have you been able to get the Pi gateway working? Before I spend more time troubleshooting my own setup here and hack away further at the RFM69_new.cpp code it would be good to know whether I'm wasting my time, doing something stupid or not. If you got it working with only the changes you mention then that means I'm doing something wrong. Thank you!

[556duckvader]

I too would like to know if you every got this working. I would like to set up the one I have as a gateway as well. I am wanting to log pool temp and PSI data to a database.

[paulsp]

@556duckvader I did not get the bonnet working through the mysensor library. I ended up using the Adafruit python client library and posting data to MQTT as a workaround.

[Mike R]

paulsp........Any chance of getting a copy of your code you used? I really only want the nodes to send data to a pi zero, and the zero to send an mqtt message. I plan on doing everything else in node red and home assistant. Is that similar to your setup. Thanks!

[FlyingSaucrDude]

I'm usually loathe to post to an ancient topic, but since this post is near the top of search results for "adafruit rfm69 bonnet mysensors" I thought this would be the best place to post the solution to the OP's problem.

By doing the following, you should be able to get an Adafruit RFM69 Bonnet on a Raspberry Pi Zero talking to your other RFM69-based MySensors nodes:

1. I started by checking out the head of the development branch (specifically commit aa76d26615, which was the head at the time, but hopefully future versions will work too).
2. I commented out the code that prevented toggling the CS_PIN as @paulsp described in post #1
3. I then built mysgw on my Rasperry Pi (happened to be a Pi Zero, but hopefully that's irrelevant) using the following command:

./configure --my-transport=rfm69 --my-rfm69-frequency=915 --my-is-rfm69hw --my-gateway=ethernet --my-port=5003 --my-rfm69-cs-pin=26 --my-rfm69-irq-pin=15 --extra-cxxflags="-DMY_RFM69_RST_PIN=22" --spi-spidev-device=/dev/spidev0.1 --spi-driver=SPIDEV

With this configuration, I was able to successfully get my RPi-based gateway using an Adafruit RFM69 radio bonnet talking to (and receiving from) various Moteino-based MySensors RFM69 nodes. I think the key difference was that I had to tell the MySensors gateway to use the spidev driver with the --spi-spidev-device=/dev/spidev0.1 --spi-driver=SPIDEV flags (instead of the BCM driver, which is the default).

Obviously if you're using a different frequency for your RFM69 radio (or a different gateway type or port) you should adjust the --my-rfm69-frequency=915 --my-gateway=ethernet --my-port=5003 flags appropriately.

[FarmerEd]

@FlyingSaucrDude

What great timing (for me anyway), only this week I purchased the Adafruit RFM95 Bonnet version, and this thread is the only thing returned in a quick search. Your solution works for RFM95 also.

I didn't need to comment out the code that prevented toggling the CS_PIN, but I'm using the development version as the main branch dose not seem to build on Pi OS Bullseye.

./configure --my-transport=rfm95 --my-rfm95-frequency=868 --my-gateway=ethernet --my-port=5003 --my-rfm95-cs-pin=26 --my-rfm95-irq-pin=15 --extra-cxxflags="-DMY_RFM95_RST_PIN=22" --spi-spidev-device=/dev/spidev0.1 --spi-driver=SPIDEV

Thanks to your post I got this working in a few min of trying, would have taken me much longer otherwise, so thank you for posting to an ancient thread.