[Solved] Arduino Nanos don't work as nodes

Avamander

My issue is rather simple, no matter what I do, Arduino Nano nodes are unable to act as nodes.

I have a working pair of an Arduino Nano based GW and an Arduino Mega 2560 based node.

I have:

Switched the radios between the nodes, the same radios that work on the GW and the Mega work on each other.
Tried PA+LNA and two different regular nRF24 boards (no, not the COB ones)
Built three new boards to plug the radio and the Nano into -
Tried 1uF, 10uF and 470uF decoupling all separately
Tried both with and without MY_PARENT_NODE_ID and MY_PARENT_NODE_IS_STATIC
Tried with and without MY_TRANSPORT_WAIT_READY_MS
I wiped the EEPROM of all the devices
Tried an external 3.3V regulator
With both the old and new Nano bootloader
Multiple Nano boards
Downloaded newer Arduino IDE and newest MySensors
Switched channel and tried different power levels

But the node still either outputs:

16 MCO:BGN:INIT REPEATER,CP=RNNRA---,FQ=16,REL=255,VER=2.3.2
27 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSM:INIT:STATID=1
38 TSF:SID:OK,ID=1
40 TSM:FPAR
45 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2052 !TSM:FPAR:NO REPLY
2054 TSM:FPAR
2058 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4065 !TSM:FPAR:NO REPLY
4067 TSM:FPAR
4071 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6078 !TSM:FPAR:NO REPLY
6080 TSM:FPAR
6084 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8091 !TSM:FPAR:FAIL
8092 TSM:FAIL:CNT=1
8094 TSM:FAIL:DIS
8096 TSF:TDI:TSL
18098 TSM:FAIL:RE-INIT
18100 TSM:INIT
18106 TSM:INIT:TSP OK
18108 TSM:INIT:STATID=1
18111 TSF:SID:OK,ID=1
18113 TSM:FPAR
18117 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
20124 !TSM:FPAR:NO REPLY
20126 TSM:FPAR

or with MY_TRANSPORT_WAIT_READY_MS:

16 MCO:BGN:INIT REPEATER,CP=RNNRAS--,FQ=16,REL=255,VER=2.3.2
54 TSM:INIT
58 TSF:WUR:MS=1
64 TSM:INIT:TSP OK
66 TSM:INIT:STATID=1
68 TSF:SID:OK,ID=1
69 TSM:FPAR
70 TSM:FPAR:STATP=0
72 MCO:BGN:INIT OK,TSP=0
74 TSM:ID
1
Sensor: 17
76 !MCO:SND:NODE NOT REG
79 MCO:SLP:MS=500,SMS=0,I1=255,M1=255,I2=255,M2=255
84 !MCO:SLP:REP
86 TSM:ID:OK
87 TSM:UPL
123 !TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=NACK:1
2
Sensor: 34
586 !MCO:SND:NODE NOT REG
589 MCO:SLP:MS=500,SMS=0,I1=255,M1=255,I2=255,M2=255
594 !MCO:SLP:REP

Node code:

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24

#define MY_REPEATER_FEATURE
#define MY_TRANSPORT_SANITY_CHECK
#define MY_SIGNAL_REPORT_ENABLED
#define MY_RF24_CE_PIN     9
#define MY_RF24_CS_PIN     10
#define MY_RF24_CHANNEL   29
#define RF24_DATARATE      RF24_2MBPS
#define RF24_PA_LEVEL      RF24_PA_MIN
#define RF24_PA_LEVEL_GW   RF24_PA_MIN
#define MY_NODE_ID         1
#define MY_PARENT_NODE_ID  0
#define MY_PARENT_NODE_IS_STATIC

#define MY_TRANSPORT_WAIT_READY_MS 1

#include <MySensors.h>

uint32_t SLEEP_TIME = 500; // Sleep time between reads (in milliseconds)

MyMessage msg(0, V_LIGHT_LEVEL);

void presentation()
{
  pinMode(A7, INPUT);
  
  Serial.begin(115200);
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Basicsensor 1", "0.1");

  // Register all sensors to gateway (they will be created as child devices)
  delay(10);
  present(0, S_LIGHT_LEVEL, F("Light level sensor"), true);
}

uint16_t lightLevel = 0;
uint16_t lastLightLevel = 0;

void loop()
{
  lightLevel = analogRead(A7);

  if (lightLevel != lastLightLevel) {
    Serial.print("Sensor: ");
    Serial.println(lightLevel);
    send(msg.setSensor(0).setType(V_LIGHT_LEVEL).set(lightLevel));
    lastLightLevel = lightLevel;
  }

  sleep(SLEEP_TIME);
}

I now suspect there's a bug somewhere in MySensors introduced by some newer version affecting Arduino Nanos. Because I remember MySensors working on Nanos a while ago.

Maybe someone here has some ideas how to narrow the issue down?

alowhum

I created a new gateway on an Arduino Nano today, and that worked. Not sure if that was using the very latest MySensors though. The rest of my network is all based on the RF-Nano, which I'm a big fan of. It shields me from exactly these types of issues :-)

How are you powering them?

Tried an external 3.3V regulator

The Nano itself runs on 5v, but I suspect you know that.

Have you tried enabling the advanced radio debug option? (I forget it's name). That can magicaly enable things sometimes. At the very least it will tell you more about what's going on.

Are you sure there's nothing like encrpytion on the gateway?

Built three new boards to plug the radio and the Nano into -

Have you tried replacing all the wires between the nano and the radio module?

I recommend just buying the Arduino Nano Wireless Expansion Board. They cost a dollar on Aliexpress.

Maybe you have some of those fake Atmel chips?

alowhum

pinMode(A7, INPUT); should not be in presentation. It should be in setup. Similarly, don't put Serial.begin(115200); in there. All that should be in presentation function is sendSketchInfo and present.

Also, don't use "delay", use wait() instead.

And where is your setup function in the first place?

alowhum

Also, your code never loads MySensors? It's commented out?

Your node code is very strange.

Avamander

@alowhum said in Arduino Nanos don't work as nodes:

How are you powering them?

USB, tried a wall-wart and two different PCs.

Are you sure there's nothing like encrpytion on the gateway?

Yes, it's the default gateway sketch, except configured to use the right channel, data rate and nRF24.

Have you tried replacing all the wires between the nano and the radio module?

Yeah, I have multiple boards, some years old and have worked with other nRF24 projects. Plus, any wiring changes actually break it for things such as RF24.

Have you tried enabling the advanced radio debug option? (I forget it's name).

I'll look into that.

Maybe you have some of those fake Atmel chips?

Three of them bought at different times, and the only issues are with MySensor? :P Seems unlikely.

Avamander

Also, your code never loads MySensors? It's commented out?

Um, line 22 #include <MySensors.h>

Your node code is very strange.

It was of the examples, barely modified.

alowhum

@Avamander said in Arduino Nanos don't work as nodes:

Um, line 22 #include <MySensors.h>

Ah, you're right. Have been programming in other languages lately, where that indicates a comment.

alowhum

Is there a reason you're swapping your CE and CS pins?

Avamander

@alowhum said in Arduino Nanos don't work as nodes:

Is there a reason you're swapping your CE and CS pins?

Because they're wired that way and it doesn't/shouldn't matter.

alowhum

What happens if you remove everything but the essentials for your network here?

#define MY_REPEATER_FEATURE
#define MY_TRANSPORT_SANITY_CHECK
#define MY_SIGNAL_REPORT_ENABLED
#define MY_RF24_CE_PIN     9
#define MY_RF24_CS_PIN     10
#define MY_RF24_CHANNEL   29
#define RF24_DATARATE      RF24_2MBPS
#define RF24_PA_LEVEL      RF24_PA_MIN
#define RF24_PA_LEVEL_GW   RF24_PA_MIN
#define MY_NODE_ID         1
#define MY_PARENT_NODE_ID  0
#define MY_PARENT_NODE_IS_STATIC

#define MY_TRANSPORT_WAIT_READY_MS 1

Maybe only leave #define MY_RF24_CHANNEL 29?

alowhum

Look for something like MY_DEBUG_VERBOSE_NRF24 - something along those lines, for that debug option I mentioned.

Avamander

@alowhum

// Enable debug prints to serial monitor
#define MY_DEBUG
#define MY_DEBUG_VERBOSE_RF24
 
// Enable and select radio type attached
#define MY_RADIO_NRF24
#define MY_TRANSPORT_SANITY_CHECK
#define MY_RF24_CE_PIN     9
#define MY_RF24_CS_PIN     10
#define MY_RF24_CHANNEL    29
#define RF24_DATARATE      RF24_2MBPS
#define RF24_PA_LEVEL      RF24_PA_MIN
#define RF24_PA_LEVEL_GW   RF24_PA_MIN
#define MY_NODE_ID         1

16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=16,REL=255,VER=2.3.2
26 TSM:INIT
28 TSF:WUR:MS=0
29 RF24:INIT:PIN,CE=9,CS=10
31 RF24:SBY
32 RF24:WBR:REG=0,VAL=14
39 RF24:WBR:REG=3,VAL=3
41 RF24:WBR:REG=4,VAL=95
44 RF24:WBR:REG=5,VAL=29
47 RF24:WBR:REG=6,VAL=37
49 RF24:WBR:REG=29,VAL=4
51 RF24:RBR:REG=29,VAL=4
53 RF24:RBR:REG=6,VAL=37
55 RF24:RBR:REG=5,VAL=29
58 RF24:WBR:REG=2,VAL=2
60 RF24:WBR:REG=1,VAL=0
62 RF24:WBR:REG=28,VAL=3
64 RF24:FRX
65 RF24:FTX
66 RF24:WBR:REG=7,VAL=112
69 TSM:INIT:TSP OK
70 TSM:INIT:STATID=1
72 RF24:WBR:REG=2,VAL=3
74 RF24:WBR:REG=1,VAL=1
76 RF24:STL
78 RF24:WBR:REG=0,VAL=15
80 RF24:WBR:REG=10,VAL=1
82 TSF:SID:OK,ID=1
84 TSM:FPAR
86 RF24:SPL
87 RF24:WBR:REG=0,VAL=14
89 RF24:OWP:RCPT=255
91 RF24:WBR:REG=10,VAL=255
93 RF24:WBR:REG=16,VAL=255
96 RF24:TXM:TO=255,LEN=7
98 RF24:FTX
99 RF24:WBR:REG=4,VAL=80
103 RF24:WBR:REG=7,VAL=112
106 ?RF24:TXM:MAX_RT
108 RF24:FTX
109 RF24:WBR:REG=4,VAL=95
111 RF24:STL
113 RF24:WBR:REG=0,VAL=15
115 RF24:WBR:REG=10,VAL=1
117 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2125 !TSM:FPAR:NO REPLY
2127 TSM:FPAR
2128 RF24:SPL
2130 RF24:WBR:REG=0,VAL=14
2132 RF24:OWP:RCPT=255
2135 RF24:WBR:REG=10,VAL=255
2138 RF24:WBR:REG=16,VAL=255
2140 RF24:TXM:TO=255,LEN=7
2143 RF24:FTX
2144 RF24:WBR:REG=4,VAL=80
2149 RF24:WBR:REG=7,VAL=112
2151 ?RF24:TXM:MAX_RT
2153 RF24:FTX
2155 RF24:WBR:REG=4,VAL=95
2157 RF24:STL
2158 RF24:WBR:REG=0,VAL=15
2161 RF24:WBR:REG=10,VAL=1
2163 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4171 !TSM:FPAR:NO REPLY
4173 TSM:FPAR
4174 RF24:SPL
4175 RF24:WBR:REG=0,VAL=14
4178 RF24:OWP:RCPT=255
4180 RF24:WBR:REG=10,VAL=255
4184 RF24:WBR:REG=16,VAL=255
4186 RF24:TXM:TO=255,LEN=7
4189 RF24:FTX
4190 RF24:WBR:REG=4,VAL=80
4195 RF24:WBR:REG=7,VAL=112
4197 ?RF24:TXM:MAX_RT
4199 RF24:FTX
4201 RF24:WBR:REG=4,VAL=95
4203 RF24:STL
4204 RF24:WBR:REG=0,VAL=15
4207 RF24:WBR:REG=10,VAL=1
4209 ?TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6217 !TSM:FPAR:NO REPLY

Still no reply.

niclas

I'm not super experienced using mysensors but I do have 3 nodes working and when first settings things up I had some problems with NODE IDs. It looks like you are setting a Static node Id? Is that ID "free" in the gateway? Have you tried powering of all the nodes you have running, wiping the EEPROM of the gateway, powering up the gateway and shortly after powering up the node?

Someone else perhaps knows this better but, if the gateway don't want to include the node, does that generate the FPAR:No reply?

And also, how is the interrupt pin connected?

electrik

I use Arduinos all the time and have problem with them.
I suggest to start with one of the examples.

The RF channel is the same everywhere I guess?
What does the output on the gateway say?

Avamander

@niclas

It looks like you are setting a Static node Id? Is that ID "free" in the gateway?

Yes, there are no other nodes (other than the one with a different static node ID that works)

Have you tried powering of all the nodes you have running,

Yes.

wiping the EEPROM of the gateway, powering up the gateway and shortly after powering up the node?

Yes, I've wiped EEPROMs of all the nodes.

niclas

@Avamander I meant, have you erased the EEPROM of the gateway?

Avamander

@niclas

I meant, have you erased the EEPROM of the gateway?

Yes, that too.

And also, how is the interrupt pin connected?

The radio's IRQ pin is not connected. (The IRQ pin is only required to be connected if the MY_RX_MESSAGE_BUFFER_FEATURE is defined in the sketch.)

niclas

@Avamander Regarding the interrupt pin, at least when using the RFM95 I need to have the pin connected to be able to receive anything. It doesnt poll the module to check for incoming messages. Maybe its different with nRF24.

I haven't tried messing with the MY_RX_MESSAGE_BUFFER_FEATURE so I wouldnt know about that.

Avamander

@niclas

Well, the documentation says I don't have to have it connected.

@electrik

I suggest to start with one of the examples.

The gateway and node both are examples with the minimal required changes.

The RF channel is the same everywhere I guess?

Yes.

What does the output on the gateway say?

Nothing, totally silent. When I plug in the Mega node, then it starts outputting all the sensor and other data.

Anyways, the weird thing here is that I remember this working a few years or so ago on the same boards and stuff, it just doesn't work now and I have 0 clue why. I'm thinking about downgrading MySensors to 1.something

niclas

@Avamander Found the documentation you were referring to and yes. Seems to be true for the RF24 which I haven't used in a long time.

#define MY_RX_MESSAGE_BUFFER_FEATURE

This enables the receiving buffer feature.

This feature is currently not supported for anything but RF24. Require MY_RF24_IRQ_PIN to be set.

Note: Not supported on ESP8266, ESP32, STM32, nRF5 and sketches that use SoftSPI. See below issue for details https://github.com/mysensors/MySensors/issues/1128

Definition at line 2406 of file MyConfig.h.

[Solved] Arduino Nanos don't work as nodes

26

11.7k

11.2k

113.1k