[n00b]]Ethernet GW - without NF24

brix7be

hum, strange.
I continue to search a solution.
I'll give you a feed back ;-).

Thanks

brix7be

It doesn't work.
But i found the code of Bram81 http://forum.mysensors.org/topic/1591/how-to-add-a-sensor-to-the-serial-gateway/22
and I can compile it well.
And it calls the gw.sendSketchInfo("Soil_Moist_Sensor_grb", "1.15");

Do you have another tip?

hek

remove "gw." from the call.

brix7be

You are right, it blocks when i call sendSketchInfo directly (without to be an attribute of gw) !?!

brix7be

Here is the merged code
Thanks for the advices

// BELOW the gateway W5100 sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
//#define MY_RADIO_NRF24 
//#define MY_RADIO_RFM69 // I DONT WANT TO USE THE RADIO MODULE

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with 
// radio on the same spi bus.
//#if !defined(MY_W5100_SPI_EN)
//  #define MY_SOFTSPI
//  #define MY_SOFT_SPI_SCK_PIN 14
//  #define MY_SOFT_SPI_MISO_PIN 16
//  #define MY_SOFT_SPI_MOSI_PIN 15
//#endif  

// When W5100 is connected we have to move CE/CSN pins for NRF radio
//#define MY_RF24_CE_PIN 5
//#define MY_RF24_CS_PIN 6

// Enable to UDP          
//#define MY_USE_UDP

//#define MY_IP_ADDRESS 192,168,1,100   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
//#define MY_PORT 5003 
     
#define IP_PORT 5003        // The port you want to open 
IPAddress myIp (192, 168, 1, 100);  // Configure your static ip-address here    COMPILE ERROR HERE? Use Arduino IDE 1.5.7 or later!

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
//#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };  // DEAD BEEF FEED

// a R/W server on the port
EthernetServer server = EthernetServer(IP_PORT);
// handle to open connection
EthernetClient client = EthernetClient();

// Flash leds on rx/tx/err
//#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
//#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
//#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
//#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3 

//#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

#include <SPI.h>

#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensor.h>


//-------------------------------------------------------------
//Below the Dallas temp sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensor.h>  
#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

char inputString[MAX_RECEIVE_LENGTH] = "";    // A string to hold incoming commands from serial/ethernet interface
int inputPos = 0;
bool sentReady = false;

void output(const char *fmt, ... ) {
   va_list args;
   va_start (args, fmt );
   vsnprintf_P(serialBuffer, MAX_SEND_LENGTH, fmt, args);
   va_end (args);
   Serial.print(serialBuffer);
   server.write(serialBuffer);
}

void setup()  
{ 
  // ////Prepare the ethernet connection 
  Ethernet.begin(mac, myIp);

  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

hek

Looks like you added your own stuff..

@brix7be said:

IPAddress myIp (192, 168, 1, 100); // Configure your static ip-address here COMPILE ERROR HERE? Use Arduino IDE 1.5.7 or later!

Should simply be
#define MY_IP_ADDRESS 192, 168, 1, 100 // If this is disabled, DHCP is used to retrieve address

And what the following doing here?

// a R/W server on the port
EthernetServer server = EthernetServer(IP_PORT);
// handle to open connection
EthernetClient client = EthernetClient();

And you include <SPI.h> and <MySensor.h> twice.

brix7be

to be honnest, i don't know ...

brix7be

With the #define MY_IP_ADDRESS i can't compile the projet.
With the arduino command it works now, i can ping it on 192.168.1.100.
But still nothing in domoticz.
Am I on the right way?
thanks again :-)

// BELOW the gateway W5100 sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable to UDP          
//#define MY_USE_UDP

//#define MY_IP_ADDRESS 192,168,1,100   // If this is disabled, DHCP is used to retrieve address
byte ip[] = { 192, 168, 1, 100 }; 
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003 

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
//#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
byte mac [] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};

#include <SPI.h>
#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensor.h>

//-------------------------------------------------------------
//Below the Dallas temp sketch

#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

void setup()  
{ 
  // ////Prepare the ethernet connection 
  Ethernet.begin(mac , ip);
  wait(1000);
  
    // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);

}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

hek

I don't understand.. why do you declare ip and mac like that? It most surely isn't picked up by the library. You're probably just getting an ip from your DHCP server.

What compile error do you get when using the defines?

brix7be

i've changed as before and it won't compile.
The error is:
no matching function for call to 'EthernetClass::begin(int, int, int, int, int, int, int, int, int, int)'
No it takes the ip I put on the code before, cause the ping respond at this one.
Thks

// BELOW the gateway W5100 sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable to UDP          
//#define MY_USE_UDP

#define MY_IP_ADDRESS 192,168,1,100   // If this is disabled, DHCP is used to retrieve address
//byte ip[] = { 192, 168, 1, 100 }; 
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003 

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
//byte mac [] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};

#include <SPI.h>
#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensor.h>

//-------------------------------------------------------------
//Below the Dallas temp sketch

#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

void setup()  
{ 
  // ////Prepare the ethernet connection 
  Ethernet.begin(MY_MAC_ADDRESS , MY_IP_ADDRESS);
  wait(1000);
  
    // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);

}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

brix7be

The final goal for me is the build ethernet sensor(s) (2 or 3 one each arduino board) connected to domoticz by lan gw.

brix7be

Is there anyone who have done a sketch to connect sensor directly on an ethernet gateway ?
Iam searching a working exemple or a working draft to see the process to build my own code.
Thank everyone for your advices.

brix7be

Hi Hek, Everyone,

I've clean the approximative sketch I've made before to simply try to see the value of a DS18b20 sensor trough a serial gw in domoticz.
So i've placed the merged code below to have your advices.
In domoticz's log i can see the declaration of the gw but neither the dallas sensor!?

Does someone could check my sketch please?
To be sure that the arduino see the dallas, i've tested a sketch wich send the value to the serial terminal (it works properly :-).

Thank you in advance for your help.
Have a nice sunday all. (clouday in belgium today ;-)).

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Flash leds on rx/tx/err
//#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
//#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
//#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
//#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3 

//#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

#include <SPI.h>
#include <MySensor.h>  
#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

void setup() { 
  // Setup locally attached sensors
  
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}

void presentation() {
 // Present locally attached sensors 
 
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop() { 
  // Send locally attached sensor data here

  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

To be complete, there is the domoticz log.

2015-10-25 10:44:40.157 MySensors: Using serial port: COM3
2015-10-25 10:44:41.892 MySensors: Gateway Ready...
2015-10-25 10:44:41.892 MySensors: Node: 0, Sketch Name: Temperature Sensor
2015-10-25 10:44:41.946 MySensors: Node: 0, Sketch Version: 1.1

brix7be

No idea?

hek

Sensors attached to gateway (node id=0) is a new feature.
Might be Domoticz filtering these type of messages perhaps?

@GizMoCuz might know if this is the case.

afick

Hello,
I have created ethernet gateway :) with 2 sensors :) (DHT11, and door/windows sensor) all data are send to domoticz without problem.But when i adds "przekaznik" - one channel relay - i can't send/receive data about this relay. Can anyone check why ?

sorry for mess in code

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable gateway ethernet module type
#define MY_GATEWAY_W5100

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with
// radio on the same spi bus.
#define MY_SOFTSPI
#define MY_SOFT_SPI_SCK_PIN 14
#define MY_SOFT_SPI_MISO_PIN 16
#define MY_SOFT_SPI_MOSI_PIN 15

// When W5100 is connected we have to move CE/CSN pins for NRF radio
#define MY_RF24_CE_PIN 5
#define MY_RF24_CS_PIN 6

// Enable to UDP
//#define MY_USE_UDP

#define MY_IP_ADDRESS 192,168,0,250   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3

#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

//Przekaznik
#define MY_REPEATER_FEATURE

#define RELAY_1  22  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

#include <SPI.h>

#if defined(MY_USE_UDP)
#include <EthernetUdp.h>
#endif


#include <Ethernet.h>
#include <MySensor.h>
#include <DHT.h>   //dodany czujnik

//czujnik temp i wilgotnosci
#define CHILD_ID_HUM 0
#define CHILD_ID_TEMP 1
#define HUMIDITY_SENSOR_DIGITAL_PIN 3
#define DOOR_ID1 4
#define DOOR_ID1_PIN A0

unsigned long SLEEP_TIME = 300; // Sleep time between reads (in milliseconds)
DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);

MyMessage msgDOOR_ID1(DOOR_ID1, V_TRIPPED);
int old_DOOR_ID1_STATE = -1;


void setup()
{

  //temp + hum
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
  metric = getConfig().isMetric;

  //  kontaktron DOOR_ID1
  pinMode(DOOR_ID1_PIN, INPUT);

  //  //przekaznik
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
  //    // Then set relay pins in output mode
      pinMode(pin, OUTPUT);
  //    // Set relay to last known state (using eeprom storage)
      digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
    }

}

void presentation()
{

  //temp + hum
  // Send the Sketch Version Information to the Gateway
  sendSketchInfo("Humidity", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID_HUM, S_HUM);
  present(CHILD_ID_TEMP, S_TEMP);
  present(DOOR_ID1, S_DOOR);

  //przekaznik
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay", "1.0");

  for (int sensor = 1, pin = RELAY_1; sensor <= NUMBER_OF_RELAYS; sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_LIGHT);
    Serial.print("Petla presentation");
  }

}

void loop()
{
  //temp + hum
  delay(dht.getMinimumSamplingPeriod());
  float temperature = dht.getTemperature();
  if (isnan(temperature)) {
    Serial.println("Failed reading temperature from DHT");
  } else if (temperature != lastTemp) {
    lastTemp = temperature;
    if (!metric) {
      temperature = dht.toFahrenheit(temperature);
    }
    send(msgTemp.set(temperature, 1));
    Serial.print("T: ");
    Serial.println(temperature);
  }

  float humidity = dht.getHumidity();
  if (isnan(humidity)) {
    Serial.println("Failed reading humidity from DHT");
  } else if (humidity != lastHum) {
    lastHum = humidity;
    send(msgHum.set(humidity, 1));
    Serial.print("H: ");
    Serial.println(humidity);
  }


  int DOOR_ID1_STATE = analogRead(DOOR_ID1_PIN);
  Serial.print("Analog= ");
  Serial.println(DOOR_ID1_STATE);
  Serial.println(old_DOOR_ID1_STATE);

  if (DOOR_ID1_STATE == 0) {
    DOOR_ID1_STATE = 0;
    send(msgDOOR_ID1.set(DOOR_ID1_STATE));
    old_DOOR_ID1_STATE = DOOR_ID1_STATE;
    Serial.print("drzwi_1=");
    Serial.println(DOOR_ID1_STATE);

  } else {
    DOOR_ID1_STATE = 1;
    send(msgDOOR_ID1.set(DOOR_ID1_STATE));
    old_DOOR_ID1_STATE = DOOR_ID1_STATE;
    Serial.print("drzwi_2=");
    Serial.println(DOOR_ID1_STATE);
  }
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type == V_LIGHT) {
    // Change relay state
    digitalWrite(message.sensor - 1 + RELAY_1, message.getBool() ? RELAY_ON : RELAY_OFF);
    // Store state in eeprom
    saveState(message.sensor, message.getBool());
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}

hek

Just did some verification of message receiving in gateway on the ESP8266 sent from my shell (using netcat). Messages is showing up in receive() just fine here.

Are you sending to node 0 from Domoticz? What does the log say in the gateway?

afick

Nothing special

0;0;3;0;9;Starting...
IP: 192.168.0.250
0;0;3;0;9;gateway started, id=0, parent=0, distance=0

Domoticz log

 2015-11-09 23:09:50.588 (GW) Temp + Humidity (TempHum)
2015-11-09 23:09:53.599 (GW) Temp + Humidity (TempHum)
2015-11-09 23:09:56.614 (GW) Temp + Humidity (TempHum)
2015-11-09 23:09:56.620 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:00.632 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:00.680 (GW) Lighting 2 (Security Sensor)
2015-11-09 23:10:03.706 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:07.718 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:12.730 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:17.745 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:21.762 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:22.770 (GW) Lighting 2 (Security Sensor)
2015-11-09 23:10:27.791 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:31.805 (GW) Temp + Humidity (TempHum)
2015-11-09 23:10:32.812 (GW) Temp + Humidity (TempHum)

I'm receiving only this kind of information.

How can i send "0" from domoticz to GW ?

hek

Your have messed up the presentation of your S_LIGHT devices in the loop. They start with id 1 in the loop. But that id has already been used by CHILD_ID_TEMP.

afick

Even if i change CHILD_ID_RELAY (to 5 or 6 ) sill the same.

[n00b]]Ethernet GW - without NF24

13

11.7k

11.2k

113.0k