MySensors Raspberry port suggestions

marceloaqno

@raptorjr
I think PiDome also supports MQTT Gateway. Did you try that?

raptorjr

I don't really understands what MQTT is and how to use it. But maybe I'll try that. Would like to see how PiDome works and if I like it better than Domoticz.

marceloaqno

@raptorjr PiDome should work now (https://forum.mysensors.org/topic/2389/added-support-for-local-mysensors-rpi-direct-radio-connection).

You need to add --my-serial-is-pty when running ./configure or uncomment the line #define MY_IS_SERIAL_PTY in mysGateway.cpp.

raptorjr

@marceloaqno

Wow. That was fast work =)

Trying it now and the /dev/ttyMySensorsGateway is created. Followed the guide in the link you provided. Everything goes great until the last step. I don't see the message "Gateway startup complete". So I don't know if I have any communication between PiDome and the gateway?

I'll start reading forums and see if I can find a solution. Or if I missed something.

hawk_2050

@marceloaqno I've got the MysGateway configured and built to be an MQTT Gateway. I have a node (MySensors v2.01) sending temperature, humidity and voltage data to the Gateway. Looking at the stdout on the Raspberry Pi I can see that the information is being correctly received but there seems to be a problem with the published messages. I'm getting "send: Broken pipe" messages. I've copied and pasted some of the MysGateway stdout terminal output below. Do you have any insights on what might be going wrong?

Thanks very much

Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
TSF:MSG:BC
TSF:MSG:FPAR REQ,ID=20
TSF:CHKUPL:OK
TSF:MSG:GWL OK
TSF:MSG:SEND,0-0-20-20,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
TSF:MSG:READ,20-20-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
TSF:MSG:PINGED,ID=20,HP=1
TSF:MSG:SEND,0-0-20-20,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
TSF:MSG:READ,20-20-0,s=255,c=3,t=12,pt=0,l=3,sg=0:0.5
Sending message on topic: MyGW2out/20/255/3/0/12
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-0,s=2,c=0,t=23,pt=0,l=0,sg=0:
Sending message on topic: MyGW2out/20/2/0/0/23
TSF:MSG:READ,20-20-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
TSF:MSG:SEND,0-0-20-20,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
TSF:MSG:READ,20-20-0,s=1,c=1,t=0,pt=7,l=5,sg=0:19.9
Sending message on topic: MyGW2out/20/1/1/0/0
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-0,s=2,c=1,t=38,pt=7,l=5,sg=0:3319.0
Sending message on topic: MyGW2out/20/2/1/0/38
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-0,s=0,c=1,t=1,pt=7,l=5,sg=0:58.6
Sending message on topic: MyGW2out/20/0/1/0/1
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18

b0rmann

feature request: logging via syslog (journald). or unbuffered debug output to stdio

raptorjr

@marceloaqno

I think there may be a memory leak in the gateway. While using it as a ethernet gateway I loose about 100Mb every day, if my only node is turned on. After a few days I can't even login with SSH and need to remove the power to my Pi3 to reboot it.

If I turn off my node, memory usage is normal. So it seems to have something to to when messages is received/transmitted. Is there anything I can do to get more details where the problem could be?

I'm using the image from Domoticz where everything is installed, and have only added mysGateway.

marceloaqno

@raptorjr @hawk_2050 I'll check.
@b0rmann I'll do something about it.

b0rmann

@raptorjr

gateway running 8 days:

pi@pi:~$ ls -ld /proc/`pidof mysGateway`
dr-xr-xr-x 7 root root 0 Aug 30 22:40 /proc/3935

memory consumption (peak) - 22M

pi@pi:~$ cat /proc/`pidof mysGateway`/status
Name:   mysGateway
State:  S (sleeping)
Tgid:   3935
Ngid:   0
Pid:    3935
PPid:   1
TracerPid:      0
Uid:    0       0       0       0
Gid:    0       0       0       0
FDSize: 256
Groups:
NStgid: 3935
NSpid:  3935
NSpgid: 3935
NSsid:  3935
VmPeak:    22108 kB
VmSize:    22108 kB
VmLck:         0 kB
VmPin:         0 kB
VmHWM:      3088 kB
VmRSS:      3088 kB
VmData:      236 kB
VmStk:       136 kB
VmExe:        80 kB
VmLib:      4392 kB
VmPTE:        30 kB
VmPMD:         0 kB
VmSwap:        0 kB
Threads:        1
SigQ:   0/7339
SigPnd: 0000000000000000
ShdPnd: 0000000000000000
SigBlk: 0000000000000000
SigIgn: 0000000000001000
SigCgt: 0000000180004002
CapInh: 0000000000000000
CapPrm: 0000003fffffffff
CapEff: 0000003fffffffff
CapBnd: 0000003fffffffff
Seccomp:        0
Cpus_allowed:   f
Cpus_allowed_list:      0-3
Mems_allowed:   1
Mems_allowed_list:      0
voluntary_ctxt_switches:        71974874
nonvoluntary_ctxt_switches:     167964

alexsh1

@marceloaqno Hi, could you please explain to me what the steps are to compile it for RPi3?
I went here - https://github.com/marceloaqno/Raspberry
Downloaded and tried to compile. The following error has come up:

pi@m:~/Raspberry-GW $ make all
make -C librf24-bcm
make[1]: Entering directory '/home/pi/Raspberry-GW/librf24-bcm'
cp utility/RPi/includes.h utility/includes.h
g++ -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c RF24.cpp
g++ -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c utility/RPi/spi.cpp
gcc -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c utility/RPi/bcm2835.c
g++ -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c utility/RPi/interrupt.c
g++ -shared -Wl,-soname,librf24-bcm.so.1 -pthread -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -o librf24-bcm.so.1.0 RF24.o spi.o bcm2835.o interrupt.o
make[1]: Leaving directory '/home/pi/Raspberry-GW/librf24-bcm'
g++ -std=c++0x -g -Wall -Wextra -Ofast -mfpu=vfp -mfloat-abi=hard -mtune=arm1176jzf-s -Ilibmysensors -Ilibrf24-bcm -pthread -DRASPBERRYPI_ARCH  -march=armv7-a -MMD -c -o src/Basic/PiGatewaySample.o src/Basic/PiGatewaySample.cpp
src/Basic/PiGatewaySample.cpp: In function ‘int main()’:
src/Basic/PiGatewaySample.cpp:63:15: error: ‘usleep’ was not declared in this scope
   usleep(10000); // 10ms
               ^
Makefile:103: recipe for target 'src/Basic/PiGatewaySample.o' failed
make: *** [src/Basic/PiGatewaySample.o] Error 1

Thanks

alexsh1

OK, I manage to install it finally.

However, again I have a problem:

./configure --my-gateway=ethernet --my-rf24-channel=1 --my-rf24-pa-level=RF24_PA_MAX --my-controller-ip-address=127,0,0,1

when I start it I have the following in the log:

failed to bind
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor

marceloaqno

Add some options to the gateway execution:

# ./examples_linux/mysGateway -h
Usage: mysGateway [options]

Options:
-h            Display a short summary of all program options.
-d            Enable debug.
-b            Become a daemon.

Debug is now disabled by default.
You can't run it as a linux daemon if debug is enabled.
When daemonized all messages will be print to syslog.

b0rmann

This post is deleted!

alexsh1

@marceloaqno Interesting. When I execute "mysGateway -h" I get the following:

pi@m:~/MySensors/examples_linux $ mysGateway -h
MCO:BGN:INIT GW,CP=RNNG---,VER=2.0.1-beta
TSM:INIT
Segmentation fault

What does "Segmentation fault' mean please?

marceloaqno

@alexsh1 You must be root to run the gateway:

$ sudo mysGateway

It seems that you are not using the latest version, -h should have shown you the options list.

alexsh1

@marceloaqno I have the latest version (downloaded yesterday). Thanks very much for your help. I got the following:

pi@m:~/MySensors/examples_linux $ sudo mysGateway -h
MCO:BGN:INIT GW,CP=RNNG---,VER=2.0.1-beta
TSM:INIT
TSM:INIT:TSP OK
TSM:INIT:GW MODE
TSM:READY
MCO:REG:NOT NEEDED
MCO:BGN:STP
MCO:BGN:INIT OK,ID=0,PAR=0,DIS=0,REG=1

In Domoticz:

2016-09-09 09:32:26.032 TCP: Reconnecting... 
2016-09-09 09:32:26.032 MySensors: connected to: 127.0.0.1:5003

I added MySensors with LAN in Domoticz (port 5003), but here a problem. I can see the node and the GW communicating:

GW:

TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
Client 0: 0;0;3;0;18;PING
TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
Client 0: 0;0;3;0;18;PING

Starting sensor (RNNNA-, 2.0.0-beta)
Radio init successful.
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
Init complete, id=255, parent=0, distance=1
requesting time
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
requesting time
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
requesting time
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
requesting time
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:
requesting time
req id
send: 255-255-0-0 s=255,c=3,t=3,pt=0,l=0,sg=0,st=ok:

The RF communication is fine, but I do not understand why Domoticz is not assigning ID.......

EDIT: I can see in Domoticz in the Hardware section:

MySensors Gateway with LAN interface
Version: ? Setup

Typically ? comes up when the controller is not recognised or not connected

EDIT2:Deleted and started fresh. Unfortunately, now the log file is flooded with the following:


mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.
mysGateway: Max number of ethernet clients reached.

marceloaqno

@alexsh1 There is a bug with --my-controller-ip-address, I'm not sure if it's your case, but try to avoid it.

I tried Domoticz here and everything seems fine:

MySensors Gateway with LAN interface
Version: 2.0.1-beta (Setup)

I recommend you to start from scratch, re-download the gateway from here:
https://github.com/marceloaqno/MySensors/tree/dev-raspberrypi

alexsh1

@marceloaqno OK, this must be the reason. I have tried the serial setup and it worked with a little tweak:

/dev/ttyUSB20 -> /dev/ttyMySensorsGateway

For whatever reason Domoticz did not see ttyMySensorsGateway so I had to create ttyUSB20

emc2

@alexsh1 said:

For whatever reason Domoticz did not see ttyMySensorsGateway so I had to create ttyUSB20

Domoticz seems to only look for ttyUSB* interfaces. One easy trick is to run ./configure with this option so you don't have to worry with symlinking

./configure --my-serial-pty=/dev/ttyUSBMySensorsGateway

BTW @marceloaqno , what does the option --my-serial-is-pty exactly do?
So far I've been running the gateway in ethernet mode for a little while and it's working flawlessly, thanks a lot for this port.

alexsh1

@emc2 said:

./configure --my-serial-pty=/dev/ttyUSBMySensorsGateway

Exallent fix! Thanks

@marceloaqno I can confirm that the Ethernet GW works fine without --my-controller-ip-address
MAny thanks for your port and help!

MySensors Raspberry port suggestions

7

11.7k

11.2k

113.0k