MySensors Raspberry port suggestions

raptorjr

Would it be possible to enable both the Serial and Ethernet communication at the same time in the gateway? I'm about to try PiDome as a controller. And it seems that it only have support for Serial gateway. But the Ethernet gateway is so practical to use when I need to debug and use MYScontroller to connect and see what is happening. Or if I would like to try OTA updates of my nodes.

mfalkvidd

@raptorjr some people have used nodered to "split" the communication to more than one controller. NodeRed has the ability to prevent certain types of messages. If two controllers are connected to the same gateway without filtering, both controllers will respond which might be very confusing for the node.

https://forum.mysensors.org/topic/4112/is-it-possible-to-connect-an-ethernet-gateway-to-node-red-and-share-it/ is a pretty good place to start

raptorjr

@mfalkvidd

Thank you. Maybe I should just try out PiDome first with serial gateway =)

But anyway, I thought that mysGateway would create something like /dev/ttyMySensorsGateway that I could then use, or ln to something like ttyUSB20, and add it in PiDome.

But after compiling and installing mysGateway with serial support I only get a a error "Unable to open the serial port /dev/ttyUSB0". Am I thinking the wrong way? Isn't mysGateway supposed to work like the old Raspberry MySensors gateway?

marceloaqno

@raptorjr Sorry, pseudo tty isn't supported. I will try to add it till the end of the day.

raptorjr

@marceloaqno

What does the serial gateway do then? Can I use it as it is today with PiDomo and a RasberryPi? Or do I need to make a dedicated stand-alone serial gateway with a Arduino and a NRF?

marceloaqno

@raptorjr
In the current state, serial gateway on RPi can only use a "real" serial port like /dev/ttyAMA0 (gpio pins) or (if an arduino is connected or a USB->Serial adapter) /dev/ttyACM0. To use PiDomo you will need to put an Arduino to the mix.

raptorjr

@marceloaqno

Thank you. I'll have to wait for pseudo tty or for PiDome to get support for Ethernet gateway.

marceloaqno

@raptorjr
I think PiDome also supports MQTT Gateway. Did you try that?

raptorjr

@marceloaqno

I don't really understands what MQTT is and how to use it. But maybe I'll try that. Would like to see how PiDome works and if I like it better than Domoticz.

marceloaqno

@raptorjr PiDome should work now (https://forum.mysensors.org/topic/2389/added-support-for-local-mysensors-rpi-direct-radio-connection).

You need to add --my-serial-is-pty when running ./configure or uncomment the line #define MY_IS_SERIAL_PTY in mysGateway.cpp.

raptorjr

@marceloaqno

Wow. That was fast work =)

Trying it now and the /dev/ttyMySensorsGateway is created. Followed the guide in the link you provided. Everything goes great until the last step. I don't see the message "Gateway startup complete". So I don't know if I have any communication between PiDome and the gateway?

I'll start reading forums and see if I can find a solution. Or if I missed something.

hawk_2050

@marceloaqno I've got the MysGateway configured and built to be an MQTT Gateway. I have a node (MySensors v2.01) sending temperature, humidity and voltage data to the Gateway. Looking at the stdout on the Raspberry Pi I can see that the information is being correctly received but there seems to be a problem with the published messages. I'm getting "send: Broken pipe" messages. I've copied and pasted some of the MysGateway stdout terminal output below. Do you have any insights on what might be going wrong?

Thanks very much

Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
TSF:MSG:BC
TSF:MSG:FPAR REQ,ID=20
TSF:CHKUPL:OK
TSF:MSG:GWL OK
TSF:MSG:SEND,0-0-20-20,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
TSF:MSG:READ,20-20-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
TSF:MSG:PINGED,ID=20,HP=1
TSF:MSG:SEND,0-0-20-20,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
TSF:MSG:READ,20-20-0,s=255,c=3,t=12,pt=0,l=3,sg=0:0.5
Sending message on topic: MyGW2out/20/255/3/0/12
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-0,s=2,c=0,t=23,pt=0,l=0,sg=0:
Sending message on topic: MyGW2out/20/2/0/0/23
TSF:MSG:READ,20-20-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
TSF:MSG:SEND,0-0-20-20,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
TSF:MSG:READ,20-20-0,s=1,c=1,t=0,pt=7,l=5,sg=0:19.9
Sending message on topic: MyGW2out/20/1/1/0/0
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-0,s=2,c=1,t=38,pt=7,l=5,sg=0:3319.0
Sending message on topic: MyGW2out/20/2/1/0/38
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18
TSF:MSG:READ,20-20-0,s=0,c=1,t=1,pt=7,l=5,sg=0:58.6
Sending message on topic: MyGW2out/20/0/1/0/1
send: Broken pipe
Attempting MQTT connection...
MQTT connected
Sending message on topic: MyGW2out/0/255/0/0/18

b0rmann

feature request: logging via syslog (journald). or unbuffered debug output to stdio

raptorjr

@marceloaqno

I think there may be a memory leak in the gateway. While using it as a ethernet gateway I loose about 100Mb every day, if my only node is turned on. After a few days I can't even login with SSH and need to remove the power to my Pi3 to reboot it.

If I turn off my node, memory usage is normal. So it seems to have something to to when messages is received/transmitted. Is there anything I can do to get more details where the problem could be?

I'm using the image from Domoticz where everything is installed, and have only added mysGateway.

marceloaqno

@raptorjr @hawk_2050 I'll check.
@b0rmann I'll do something about it.

b0rmann

@raptorjr

gateway running 8 days:

pi@pi:~$ ls -ld /proc/`pidof mysGateway`
dr-xr-xr-x 7 root root 0 Aug 30 22:40 /proc/3935

memory consumption (peak) - 22M

pi@pi:~$ cat /proc/`pidof mysGateway`/status
Name:   mysGateway
State:  S (sleeping)
Tgid:   3935
Ngid:   0
Pid:    3935
PPid:   1
TracerPid:      0
Uid:    0       0       0       0
Gid:    0       0       0       0
FDSize: 256
Groups:
NStgid: 3935
NSpid:  3935
NSpgid: 3935
NSsid:  3935
VmPeak:    22108 kB
VmSize:    22108 kB
VmLck:         0 kB
VmPin:         0 kB
VmHWM:      3088 kB
VmRSS:      3088 kB
VmData:      236 kB
VmStk:       136 kB
VmExe:        80 kB
VmLib:      4392 kB
VmPTE:        30 kB
VmPMD:         0 kB
VmSwap:        0 kB
Threads:        1
SigQ:   0/7339
SigPnd: 0000000000000000
ShdPnd: 0000000000000000
SigBlk: 0000000000000000
SigIgn: 0000000000001000
SigCgt: 0000000180004002
CapInh: 0000000000000000
CapPrm: 0000003fffffffff
CapEff: 0000003fffffffff
CapBnd: 0000003fffffffff
Seccomp:        0
Cpus_allowed:   f
Cpus_allowed_list:      0-3
Mems_allowed:   1
Mems_allowed_list:      0
voluntary_ctxt_switches:        71974874
nonvoluntary_ctxt_switches:     167964

alexsh1

@marceloaqno Hi, could you please explain to me what the steps are to compile it for RPi3?
I went here - https://github.com/marceloaqno/Raspberry
Downloaded and tried to compile. The following error has come up:

pi@m:~/Raspberry-GW $ make all
make -C librf24-bcm
make[1]: Entering directory '/home/pi/Raspberry-GW/librf24-bcm'
cp utility/RPi/includes.h utility/includes.h
g++ -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c RF24.cpp
g++ -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c utility/RPi/spi.cpp
gcc -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c utility/RPi/bcm2835.c
g++ -Wall -fPIC -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -c utility/RPi/interrupt.c
g++ -shared -Wl,-soname,librf24-bcm.so.1 -pthread -Ofast -mfpu=vfp -mfloat-abi=hard -march=armv7-a -mtune=arm1176jzf-s -o librf24-bcm.so.1.0 RF24.o spi.o bcm2835.o interrupt.o
make[1]: Leaving directory '/home/pi/Raspberry-GW/librf24-bcm'
g++ -std=c++0x -g -Wall -Wextra -Ofast -mfpu=vfp -mfloat-abi=hard -mtune=arm1176jzf-s -Ilibmysensors -Ilibrf24-bcm -pthread -DRASPBERRYPI_ARCH  -march=armv7-a -MMD -c -o src/Basic/PiGatewaySample.o src/Basic/PiGatewaySample.cpp
src/Basic/PiGatewaySample.cpp: In function ‘int main()’:
src/Basic/PiGatewaySample.cpp:63:15: error: ‘usleep’ was not declared in this scope
   usleep(10000); // 10ms
               ^
Makefile:103: recipe for target 'src/Basic/PiGatewaySample.o' failed
make: *** [src/Basic/PiGatewaySample.o] Error 1

Thanks

alexsh1

OK, I manage to install it finally.

However, again I have a problem:

./configure --my-gateway=ethernet --my-rf24-channel=1 --my-rf24-pa-level=RF24_PA_MAX --my-controller-ip-address=127,0,0,1

when I start it I have the following in the log:

failed to bind
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor
accept: Bad file descriptor

marceloaqno

Add some options to the gateway execution:

# ./examples_linux/mysGateway -h
Usage: mysGateway [options]

Options:
-h            Display a short summary of all program options.
-d            Enable debug.
-b            Become a daemon.

Debug is now disabled by default.
You can't run it as a linux daemon if debug is enabled.
When daemonized all messages will be print to syslog.

b0rmann

This post is deleted!

MySensors Raspberry port suggestions

9

11.7k

11.2k

113.0k