💬 Sensebender Gateway

[tbowmo]

@alexsh1

You might be able to compile with the standard arduino zero BSP files. But the IO mapping is not the same at all.. I have swapped some pins to make routing a bit easier. Also the SPI channels are configured a bit differently than the standard arduino, if I remember right. So I will advise to use the mysensors gateway BSP files..

[alexsh1]

@tbowmo it is already done. Thanks to your link I have now Sensebender Gateway board added.
Waiting for an ethernet board now, it has stuck in the post

[Fabien]

@tbowmo : Did you try to use this board with platformio ?

[tbowmo]

@Fabien

No, platformio is still on my bucketlist.. There is just not hours enough for everything :)

[Fabien]

@tbowmo Ok I will install arduino IDE to upgrade it to 2.1.1
Please post here iwhen you have more information. I think I will try but I have no experience with this architecture.

[delivereath]

Has anyone designed a case for the sensebender gateway ?

[tbowmo]

@delivereath

I designed one in freecad for the GW and a nrf24l01 with lna/pa and external antenna.

But I still have some fine tuning to do before releasing it, as the lid locking mechanism didn't turn out like expected.

[scalz]

Tea time..

Here is my custom box for your RFM69 Sensebender GW ! Beautiful board though ;)

No nail no screw :)

Last final minor check and i release the files, sure! (i've done one for nrf too in case..)

[alexsh1]

@scalz beautiful box!!!
Looking forward to print it too as soon as you publish it, but mine will be with nrf24l01+. Having been running both networks, I'm so much in favour of rfm69. It just works. No more caps to stabilise power or any other rf issues.

I have decided to use Moteino Mega with a built-in antenna as rfm69 gateway though - it is very small and goes inside into an RPi box. And has got more memory than atmega328p

[Fabien]

@scalz Yeah ! I will print this one.

[scalz]

Little gift.. :)

Custom box for the NRF non PA version:

A bit enlarged for NRF.

And here the 3d preview for both versions with my little cheat for bicolor as i've still not added this feature to my printer

You can see i've added a little slot near usb on the NRF version, it's for the leds indication in case box wouldn't be white (no need for white box, you can see it by transparency). I'll do the same for rfm69, and put variant stl with it or not.

Next Nrf PA version, and that'll be fine ;)

[hek]

Thank you @scalz!

[alexsh1]

@scalz Please share the STL files!

[scalz]

@alexsh1 why, i don't understand :stuck_out_tongue_winking_eye:

Here it is : http://www.thingiverse.com/thing:2084269

[scalz]

I'm proud to say enclosure files have been integrated in the MySensors Sensebender GW project and git.
So you can find the files here at Mysensors.

Enjoy :)

[MLs]

Hey it should look like this?

But you see the gap between the W5100 and Sensebende Gateway.

Sorry for a very poor camera

//Mattias

[tbowmo]

@MLs

Yes, according to the build instructions here, you can also raise the socket a bit over the pcb.

The problem is that the ethernet connector is higher than a normal IDC socket, which means you can't insert the board fully in the socket. I have searched for a higher variant of the socket, but haven't found a suitable candidate..

[alexsh1]

@tbowmo What I did was soldering the socket a bit higher. Not a problem with some soldering skills...

[alexsh1]

@scalz Thank you Sir. I am going to probably wait for the PLA version as It has been working a bit better for me.

[Disca]

Few things about the software side of this. When you plug it into your computer it appears as a "Sensebender GW", with a custom USB VID/PID. You have to override the drivers and use the "Atmel Corp. EDBG CMSIS-DAP" serial port drivers or you will have no serial port at all to communicate with the board.

Second issue, with the latest Arduino software (1.8.1), and the MySensors SAMD board package installed and MySensor library installed you get an error relating to a missing core "arduino:arduino". Solution to that one is to install the main Arduino SAMD board package which adds the necessary libraries. Secondly, after doing that you will now get another error regarding a missing "Sam.h" file, to fix that you have to manually edit the platform.txt file in "\AppData\Local\Arduino15\packages\MySensors\hardware\samd\1.0.3" with the contents of the one from "\AppData\Local\Arduino15\packages\arduino\hardware\samd\1.6.11" - just being careful to copy over the name and version lines from the top of the Mysensors platform.txt file. After that you are good to go and can finally program the board or get some data out of it :-)