Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors Mini Scene Controller

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/30/MySensors-Mini-Scene-Controller
Reply Quote 3
1 Reply Last reply
172pilot last edited by

What kind of box is this? I'm having a hard time visualizing the scale of this, but does it use something roughly the size of an outlet cover? This looks exactly like what I want to build..
Reply Quote 0
1 Reply Last reply
jtm312 last edited by @172pilot

@172pilot It is an outlet cover.
Reply Quote 0
1 Reply Last reply
172pilot last edited by

Thats perfect.. definitely have to try this.. Thanks!!
Reply Quote 0
1 Reply Last reply

4
Posts

2231
Views

Suggested Topics

Starry Sky
OpenHardware.io • temperature humidity led mysensor light contest2016 • • openhardware.io

6

3
Votes

6
Posts

2623
Views

this kind of optic fiber is probably only plastic so for a full DIY , you can use also fishing wire with a big power led or an old chistmass tree optic fiber lighted.....
Power sensor? Battery?
Development • battery battery powered • • CrankyCoder

12

0
Votes

12
Posts

3562
Views

@NeverDie Yes, you are correct - it is based on ATMega1284P. So not relevant My point is that I'd rather stick to the datasheet rather than overclock, but that's just me. And yes I realise that Moteino is overclocking, but the size, voltage and flash are really appealing to me.
💬 MDMSNode "Lighting"
OpenHardware.io • mysensors arduino nrf24l01 rfm69 light acdc light switch • • openhardware.io

37

2
Votes

37
Posts

10438
Views

Hi @aramko-aramko. Unfortunately, this model is already sold. You can look at the upgraded version of this device - MDMSNode "Lighting" Rev 1.1.
Battery based atmega328p sensor with SMD nrf24l01+
OpenHardware.io • mysensors nrf24l01 atmega328 contest2016 • • openhardware.io

22

1
Votes

22
Posts

7475
Views

@vikasjee Alex used the hardware described at the start of this thread. You will find all design documents on Openhardware.io
💬 Homini In-Wall Battery Powered Light Switch Module
OpenHardware.io • mysensors battery switch light inwall in-wall coincell • • openhardware.io

25

1
Votes

25
Posts

8204
Views

@JahFyahh - I still haven't managed to et round to it. I've been really busy since this project and its still hectic here. I'm sure i read a few reviews somewhere, here or google. Not sure.
How to check if serial gateway is operational ?
Development • arduino serial gateway • • joshmosh

4

0
Votes

4
Posts

2214
Views

@fot said: Hi! I ask my gateway about it's version (0;0;3;0;2;). It will responde with the library version number (1.4.1 in my case). It tells me that the gateway software is up and running. But it will not give me any clue about if the (NRF)network is working. That's a problem, right. I only ask the gateway if no other packages are received in $timeout seconds. /Magnus Of course ! Thank you for pushing my nose on it. Sometimes you don't see the most obvious Since my gateway is relatively close to the controller (Domoticz on a Raspi), I can do a hard reset of the gateway (via Raspi GPIO), which should resolve the issue. Cheers Josh
💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

14

1
Votes

14
Posts

4078
Views

@Samuel235 said in Homini AC Powered Relay (2) Module: OMRON G3MB-202P Okay I'm trying to help you with the fuse component. I found a datasheet for the OMRON G3MB-202P. And there are enoght information to be known for fuse selection. I try to calculate it here (and i will try it with my bad English ). The most important information is the melting integral. The Melting integral has A²s as unit. So this means the maximum current for a time can exists without damaging the device. For further information look at wikipedia. So we need any further information about: the protection which is present before (the typical circuit protection in private houses) the melting integral from the device which we want to protect the maximum voltage the maximum switching current the breaking capacity Inrush current for the switched devices (we can't know) Typical values for an automatic circuit breaker in private houses are: from 25 to 100 A²s 230 V AC 16 A So this protection isn't good enough for our relay. The relay have these values: 230 V AC 2 A maximum switching current I²t value (melting integral): 4 A²s the allowed inrush current over a small time is higher than the melting integral. It is a bit confusing i think, but if we calculate the protection for the given melting integral and it's fine. So we can define the parameters for the client (switching site of this application here) The fuse have to be: I²s value higher or equal than the I²s value from the existing protection rating voltage over 230 V AC rating current 2 A or lower (because 2 A is the maximum at 25 °C, for 40 °C it is about 1.6 A) a maximum switching time of 1 second at 2 A or lower time with higher current but below 4A²s! To calculate use the switching time from the fuse datasheet an multiply it two times with the given current for this switching time. And i think a fast blow fuse would be the best. There are SMD fuses with 10.1 x 3 mm and 250 V AC available. If there is no fuse available with the values above, we could combine multiple fuses. A possible solution could be one bigger fuse for both relays and the ac/dc component. And a smaller fuse for the switching site of the relay and the HLK-PM01. But for this it is important that the circuit have only one input for the hot one (L) of 230 V and one output for each relay. In this case we could reduce the big connectors from 6 to 4. Like (L, N, Relay1, Relay2). And the temperature fuse can work for all components too So the protection for the primary site of the HLK-PM01 is a problem i think. Because the are no information available about the I²s value from HLK-PM01. I hope you can understand my English and could follow my explanation?
💬 RFM69 Livolo 1 channel 1 way EU switch(VL-C700X-1_Ver_C2)
OpenHardware.io • mysensors livolo • • openhardware.io

8

1
Votes

8
Posts

2606
Views

@mtiutiu Wooow Wooow Wooow ! Here they are ! This one gang you designed will be my 1st Livolo hack So many many thanks @mtiutiu Best regards

MySensors Mini Scene Controller

Suggested Topics

Starry Sky
OpenHardware.io • temperature humidity led mysensor light contest2016 • • openhardware.io

Power sensor? Battery?
Development • battery battery powered • • CrankyCoder

💬 MDMSNode "Lighting"
OpenHardware.io • mysensors arduino nrf24l01 rfm69 light acdc light switch • • openhardware.io

Battery based atmega328p sensor with SMD nrf24l01+
OpenHardware.io • mysensors nrf24l01 atmega328 contest2016 • • openhardware.io

💬 Homini In-Wall Battery Powered Light Switch Module
OpenHardware.io • mysensors battery switch light inwall in-wall coincell • • openhardware.io

How to check if serial gateway is operational ?
Development • arduino serial gateway • • joshmosh

💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

💬 RFM69 Livolo 1 channel 1 way EU switch(VL-C700X-1_Ver_C2)
OpenHardware.io • mysensors livolo • • openhardware.io

34
Online

11.6k
Users

11.2k
Topics

112.9k
Posts

MySensors Mini Scene Controller

Suggested Topics

Starry Sky OpenHardware.io • temperature humidity led mysensor light contest2016 • • openhardware.io

Power sensor? Battery? Development • battery battery powered • • CrankyCoder

💬 MDMSNode "Lighting" OpenHardware.io • mysensors arduino nrf24l01 rfm69 light acdc light switch • • openhardware.io

Battery based atmega328p sensor with SMD nrf24l01+ OpenHardware.io • mysensors nrf24l01 atmega328 contest2016 • • openhardware.io

💬 Homini In-Wall Battery Powered Light Switch Module OpenHardware.io • mysensors battery switch light inwall in-wall coincell • • openhardware.io

How to check if serial gateway is operational ? Development • arduino serial gateway • • joshmosh

💬 Homini AC Powered Relay (2) Module OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

💬 RFM69 Livolo 1 channel 1 way EU switch(VL-C700X-1_Ver_C2) OpenHardware.io • mysensors livolo • • openhardware.io

34Online

11.6kUsers

11.2kTopics

112.9kPosts

Starry Sky
OpenHardware.io • temperature humidity led mysensor light contest2016 • • openhardware.io

Power sensor? Battery?
Development • battery battery powered • • CrankyCoder

💬 MDMSNode "Lighting"
OpenHardware.io • mysensors arduino nrf24l01 rfm69 light acdc light switch • • openhardware.io

Battery based atmega328p sensor with SMD nrf24l01+
OpenHardware.io • mysensors nrf24l01 atmega328 contest2016 • • openhardware.io

💬 Homini In-Wall Battery Powered Light Switch Module
OpenHardware.io • mysensors battery switch light inwall in-wall coincell • • openhardware.io

How to check if serial gateway is operational ?
Development • arduino serial gateway • • joshmosh

💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

💬 RFM69 Livolo 1 channel 1 way EU switch(VL-C700X-1_Ver_C2)
OpenHardware.io • mysensors livolo • • openhardware.io

34
Online

11.6k
Users

11.2k
Topics

112.9k
Posts