RFID and NRF24L01 Wireless Network Coding Issues

[martins]

Found the solution in this thread:

https://forum.mysensors.org/topic/2439/rfid-garage-door-opener/35

void before() {
// Make sure MFRC is disabled from the SPI bus
pinMode(RST_PIN, OUTPUT);
digitalWrite(RST_PIN, LOW);
pinMode(SS_PIN, OUTPUT);
digitalWrite(SS_PIN, LOW);
}

[rejoe2]

At least in some first test I got a second SPI device (MCP4131) on the same wires working using the before() instruction.

int CS1 = 10; //MCP4131
void before() {
  pinMode (CS1, OUTPUT);
digitalWrite(CS1, HIGH);
}

Another option may be to use SoftSPI for thenRF (see Network-Gateway-sketch).

[gohan]

@martins
Is it working for you?

[martins]

@gohan Yes

[gohan]

I can't figure out what is wrong with mine

[martins]

@gohan What is the serial output or error that you get ?

[gohan]

just look at the garage door opener link you posted, there is log and code. If I unplug the radio and use some demo code to read the rfid tag I can read it, but I can't find where it conflicts with the radio

[martins]

@gohan This is the code that works for me on my pro mini. Try it out.

Here is my pins used:

MOSI: Pin 11
MISO: Pin 12
SCK : Pin 13
SS : Pin 8 (Configurable)
RST : Pin 6 (Configurable)

/*
  Arduino RFID Access Control

  Security !

  To keep it simple we are going to use Tag's Unique IDs
  as only method of Authenticity. It's simple and not hacker proof.
  If you need security, don't use it unless you modify the code

  Copyright (C) 2015 Omer Siar Baysal

  This program is free software; you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation; either version 2 of the License, or
  (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License along
  with this program; if not, write to the Free Software Foundation, Inc.,
  51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.

*/
#define MY_DEBUG 

#define MY_RADIO_NRF24
//#define MY_RF24_PA_LEVEL RF24_PA_LOW

//#define MY_RADIO_RFM69
//#define MY_RFM69_FREQUENCY RF69_433MHZ
//#define MY_IS_RFM69HW

#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif


#define CHILD_ID 8
#define MAX_CARDS       18

#include <EEPROM.h>     // We are going to read and write PICC's UIDs from/to EEPROM
#include <SPI.h>        // RC522 Module uses SPI protocol
#include <MFRC522.h>	// Library for Mifare RC522 Devices
#include <MySensors.h>

/*
	For visualizing whats going on hardware
	we need some leds and
	to control door lock a relay and a wipe button
	(or some other hardware)
	Used common anode led,digitalWriting HIGH turns OFF led
	Mind that if you are going to use common cathode led or
	just seperate leds, simply comment out #define COMMON_ANODE,
*/

int value=0;

boolean match = false;          // initialize card match to false
boolean programMode = false;	// initialize programming mode to false
boolean replaceMaster = false;

int successRead;		// Variable integer to keep if we have Successful Read from Reader

byte storedCard[4];		// Stores an ID read from EEPROM
byte readCard[4];		// Stores scanned ID read from RFID Module
byte masterCard[4];		// Stores master card's ID read from EEPROM
byte countValidCards = 0;
/*
	We need to define MFRC522's pins and create instance
	Pin layout should be as follows (on Arduino Uno):
	MOSI: Pin 11 / ICSP-4
	MISO: Pin 12 / ICSP-1
	SCK : Pin 13 / ICSP-3
	SS : Pin 10 (8)(Configurable)
	RST : Pin 9 (6)(Configurable)
	look MFRC522 Library for
	other Arduinos' pin configuration
*/

// bool lockStatus;

#define SS_PIN 8
#define RST_PIN 6

MFRC522 mfrc522(SS_PIN, RST_PIN);  // Create MFRC522 instance.
// MFRC522::Uid validCards[MAX_CARDS];

//MyMessage lockMsg(CHILD_ID, V_LOCK_STATUS);

MyMessage msg(CHILD_ID,V_TRIPPED);


// MFRC522 mfrc522(SS_PIN, RST_PIN);	// Create MFRC522 instance.


///////////////////////////////////////// Setup ///////////////////////////////////
void setup() {
  //Protocol Configuration
  //Serial.begin(9600);	 // Initialize serial communications with PC
  
  pinMode(RST_PIN, OUTPUT);
  digitalWrite(RST_PIN, LOW);
  pinMode(SS_PIN, OUTPUT);
  digitalWrite(SS_PIN, LOW);
  
  SPI.begin();           // MFRC522 Hardware uses SPI protocol
  mfrc522.PCD_Init();    // Initialize MFRC522 Hardware

  //If you set Antenna Gain to Max it will increase reading distance
  //mfrc522.PCD_SetAntennaGain(mfrc522.RxGain_max);

  Serial.println(F("Access Control v3.4"));   // For debugging purposes
  ShowReaderDetails();	// Show details of PCD - MFRC522 Card Reader details

  if (EEPROM.read(500) != 143) {
    Serial.println(F("No Master Card Defined"));
    Serial.println(F("Scan A PICC to Define as Master Card"));
    do {
      successRead = getID();            // sets successRead to 1 when we get read from reader otherwise 0
    }
    while (!successRead);                  // Program will not go further while you not get a successful read

//    printHex(mfrc522.uid.uidByte, mfrc522.uid.size);
    
    for ( int j = 0; j < 4; j++ ) {        // Loop 4 times
      EEPROM.write( 2 + j, readCard[j] );  // Write scanned PICC's UID to EEPROM, start from address 3
    }
      
    EEPROM.write(500, 143);                  // Write to EEPROM we defined Master Card.
    delay(500);
    
    Serial.println(F("Master Card Defined"));
//    storeEeprom();
  }
  Serial.println(F("-------------------"));
  Serial.println(F("Master Card's UID"));
  for ( int i = 0; i < 4; i++ ) {          // Read Master Card's UID from EEPROM
    masterCard[i] = EEPROM.read(2 + i);    // Write it to masterCard
    Serial.print(masterCard[i], HEX);
  }

  Serial.println("");
  Serial.println(F("-------------------"));
  Serial.println(F("Everything Ready"));
  Serial.println(F("Waiting PICCs to be scanned"));
  Serial.println(EEPROM.read(500));
}

void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("RFID Gate", "1.0");
  present(CHILD_ID, S_DOOR);  
}

///////////////////////////////////////// Main Loop ///////////////////////////////////
void loop () {
  send(msg.set(value==HIGH ? 1 : 0));
  do {
    successRead = getID(); 	// sets successRead to 1 when we get read from reader otherwise 0
  }
  while (!successRead); 	//the program will not go further while you not get a successful read

  if (programMode) {
    if ( isMaster(readCard) ) { //If master card scanned again exit program mode
      Serial.println(F("Master Card Scanned"));
      Serial.println(F("Exiting Program Mode"));
      Serial.println(F("-----------------------------"));
      programMode = false;
      return;
    }
    else {
      if ( findID(readCard) ) { // If scanned card is known delete it
        Serial.println(F("I know this PICC, removing..."));
        deleteID(readCard);
        Serial.println("-----------------------------");
        Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      }
      else {                    // If scanned card is not known add it
        Serial.println(F("I do not know this PICC, adding..."));
        writeID(readCard);
        Serial.println(F("-----------------------------"));
        Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      }
    }
  }
  else {
    if ( isMaster(readCard)) {  	// If scanned card's ID matches Master Card's ID enter program mode
      programMode = true;
      Serial.println(F("Hello Master - Entered Program Mode"));
      int count = EEPROM.read(0); 	// Read the first Byte of EEPROM that
      Serial.print(F("I have "));    	// stores the number of ID's in EEPROM
      Serial.print(count);
      Serial.print(F(" record(s) on EEPROM"));
      Serial.println("");
      Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      Serial.println(F("Scan Master Card again to Exit Program Mode"));
      Serial.println(F("-----------------------------"));
    }
    else {
      if ( findID(readCard) ) {	// If not, see if the card is in the EEPROM
        Serial.println(F("Welcome, You shall pass"));
        granted(300);        	// Open the door lock for 300 ms
      }
      else {			// If not, show that the ID was not valid
        Serial.println(F("You shall not pass"));
        denied();
      }
    }
  }
}

/////////////////////////////////////////  Access Granted    ///////////////////////////////////
void granted (int setDelay) {
  // setLockState(!lockStatus, true);
  value = 1;
  send(msg.set(value==HIGH ? 1 : 0));
  smartSleep(5000);
  value = 0;
  send(msg.set(value==HIGH ? 1 : 0));
}

///////////////////////////////////////// Access Denied  ///////////////////////////////////
void denied() {
}


///////////////////////////////////////// Get PICC's UID ///////////////////////////////////
int getID() {
  // Getting ready for Reading PICCs
    if ( ! mfrc522.PICC_IsNewCardPresent())
    return 0;

  // Verify if the NUID has been readed
  if ( ! mfrc522.PICC_ReadCardSerial())
    return 0;

  Serial.print(F("PICC type: "));
  MFRC522::PICC_Type piccType = mfrc522.PICC_GetType(mfrc522.uid.sak);
  Serial.println(mfrc522.PICC_GetTypeName(piccType));

  // Check is the PICC of Classic MIFARE type
  if (piccType != MFRC522::PICC_TYPE_MIFARE_MINI &&  piccType != MFRC522::PICC_TYPE_MIFARE_1K && piccType != MFRC522::PICC_TYPE_MIFARE_4K) {
    Serial.println(F("Your tag is not of type MIFARE Classic."));
    return;
  }
  Serial.println(F("Scanned PICC's UID:"));
  for (int i = 0; i < 4; i++) {  //
    readCard[i] = mfrc522.uid.uidByte[i];
    Serial.print(readCard[i], HEX);
  }
  Serial.println("");
  mfrc522.PICC_HaltA();
  return 1;

/*  while (! mfrc522.PICC_IsNewCardPresent()) 
  {;}
  if ( ! mfrc522.PICC_IsNewCardPresent()) 
  { //If a new PICC placed to RFID reader continue
    Serial.println("No NCP");
    return 0;
  }
  if ( ! mfrc522.PICC_ReadCardSerial()) 
  {   //Since a PICC placed get Serial and continue
    Serial.println("RCS");
    return 0;
  }
  // There are Mifare PICCs which have 4 byte or 7 byte UID care if you use 7 byte PICC
  // I think we should assume every PICC as they have 4 byte UID
  // Until we support 7 byte PICCs
  Serial.println(F("Scanned PICC's UID:"));
  for (int i = 0; i < 4; i++) {  //
    readCard[i] = mfrc522.uid.uidByte[i];
    Serial.print(readCard[i], HEX);
  }
  Serial.println("");
  mfrc522.PICC_HaltA(); // Stop reading
  return 1;
  */
  
}

void ShowReaderDetails() {
  // Get the MFRC522 software version
  byte v = mfrc522.PCD_ReadRegister(mfrc522.VersionReg);
  Serial.print(F("MFRC522 Software Version: 0x"));
  Serial.print(v, HEX);
  if (v == 0x91)
    Serial.print(F(" = v1.0"));
  else if (v == 0x92)
    Serial.print(F(" = v2.0"));
  else
    Serial.print(F(" (unknown),probably a chinese clone?"));
  Serial.println("");
  // When 0x00 or 0xFF is returned, communication probably failed
  if ((v == 0x00) || (v == 0xFF)) {
    Serial.println(F("WARNING: Communication failure, is the MFRC522 properly connected?"));
    Serial.println(F("SYSTEM HALTED: Check connections."));
    while (true); // do not go further
  }
}

///////////////////////////////////////// Cycle Leds (Program Mode) ///////////////////////////////////
void cycleLeds() {
}

//////////////////////////////////////// Normal Mode Led  ///////////////////////////////////
void normalModeOn () {
}

//////////////////////////////////////// Read an ID from EEPROM //////////////////////////////
void readID( int number ) {
  int start = (number * 4 ) + 2; 		// Figure out starting position
  for ( int i = 0; i < 4; i++ ) { 		// Loop 4 times to get the 4 Bytes
    storedCard[i] = EEPROM.read(start + i); 	// Assign values read from EEPROM to array
  }
}

///////////////////////////////////////// Add ID to EEPROM   ///////////////////////////////////
void writeID( byte a[] ) {
  if ( !findID( a ) ) { 		// Before we write to the EEPROM, check to see if we have seen this card before!
    int num = EEPROM.read(0); 		// Get the numer of used spaces, position 0 stores the number of ID cards
    int start = ( num * 4 ) + 6; 	// Figure out where the next slot starts
    num++; 								// Increment the counter by one
    EEPROM.write( 0, num ); 		// Write the new count to the counter
    for ( int j = 0; j < 4; j++ ) { 	// Loop 4 times
      EEPROM.write( start + j, a[j] ); 	// Write the array values to EEPROM in the right position
    }
    successWrite();
    Serial.println(F("Succesfully added ID record to EEPROM"));
  }
  else {
    failedWrite();
    Serial.println(F("Failed! There is something wrong with ID or bad EEPROM"));
  }
}

///////////////////////////////////////// Remove ID from EEPROM   ///////////////////////////////////
void deleteID( byte a[] ) {
  if ( !findID( a ) ) { 		// Before we delete from the EEPROM, check to see if we have this card!
    failedWrite(); 			// If not
    Serial.println(F("Failed! There is something wrong with ID or bad EEPROM"));
  }
  else {
    int num = EEPROM.read(0); 	// Get the numer of used spaces, position 0 stores the number of ID cards
    int slot; 			// Figure out the slot number of the card
    int start;			// = ( num * 4 ) + 6; // Figure out where the next slot starts
    int looping; 		// The number of times the loop repeats
    int j;
    int count = EEPROM.read(0); // Read the first Byte of EEPROM that stores number of cards
    slot = findIDSLOT( a ); 	// Figure out the slot number of the card to delete
    start = (slot * 4) + 2;
    looping = ((num - slot) * 4);
    num--; 			// Decrement the counter by one
    EEPROM.write( 0, num ); 	// Write the new count to the counter
    for ( j = 0; j < looping; j++ ) { 				// Loop the card shift times
      EEPROM.write( start + j, EEPROM.read(start + 4 + j)); 	// Shift the array values to 4 places earlier in the EEPROM
    }
    for ( int k = 0; k < 4; k++ ) { 				// Shifting loop
      EEPROM.write( start + j + k, 0);
    }
    successDelete();
    Serial.println(F("Succesfully removed ID record from EEPROM"));
  }
}

///////////////////////////////////////// Check Bytes   ///////////////////////////////////
boolean checkTwo ( byte a[], byte b[] ) {
  if ( a[0] != NULL ) 			// Make sure there is something in the array first
    match = true; 			// Assume they match at first
  for ( int k = 0; k < 4; k++ ) { 	// Loop 4 times
    if ( a[k] != b[k] ) 		// IF a != b then set match = false, one fails, all fail
      match = false;
  }
  if ( match ) { 			// Check to see if if match is still true
    return true; 			// Return true
  }
  else  {
    return false; 			// Return false
  }
}

///////////////////////////////////////// Find Slot   ///////////////////////////////////
int findIDSLOT( byte find[] ) {
  int count = EEPROM.read(0); 			// Read the first Byte of EEPROM that
  for ( int i = 1; i <= count; i++ ) { 		// Loop once for each EEPROM entry
    readID(i); 								// Read an ID from EEPROM, it is stored in storedCard[4]
    if ( checkTwo( find, storedCard ) ) { 	// Check to see if the storedCard read from EEPROM
      // is the same as the find[] ID card passed
      return i; 				// The slot number of the card
      break; 					// Stop looking we found it
    }
  }
}

///////////////////////////////////////// Find ID From EEPROM   ///////////////////////////////////
boolean findID( byte find[] ) {
  int count = EEPROM.read(0);			// Read the first Byte of EEPROM that
  for ( int i = 1; i <= count; i++ ) {  	// Loop once for each EEPROM entry
    readID(i); 					// Read an ID from EEPROM, it is stored in storedCard[4]
    if ( checkTwo( find, storedCard ) ) {  	// Check to see if the storedCard read from EEPROM
      return true;
      break; 	// Stop looking we found it
    }
    else {  	// If not, return false
    }
  }
  return false;
}

///////////////////////////////////////// Write Success to EEPROM   ///////////////////////////////////
// Flashes the green LED 3 times to indicate a successful write to EEPROM
void successWrite() {
}

///////////////////////////////////////// Write Failed to EEPROM   ///////////////////////////////////
// Flashes the red LED 3 times to indicate a failed write to EEPROM
void failedWrite() {
}

///////////////////////////////////////// Success Remove UID From EEPROM  ///////////////////////////////////
// Flashes the blue LED 3 times to indicate a success delete to EEPROM
void successDelete() {
}

////////////////////// Check readCard IF is masterCard   ///////////////////////////////////
// Check to see if the ID passed is the master programing card
boolean isMaster( byte test[] ) {
  if ( checkTwo( test, masterCard ) )
    return true;
  else
    return false;
}

/**
 * Helper routine to dump a byte array as hex values to Serial. 
 */
void printHex(byte *buffer, byte bufferSize) {
  for (byte i = 0; i < bufferSize; i++) {
    Serial.print(buffer[i] < 0x10 ? " 0" : " ");
    Serial.print(buffer[i], HEX);
  }
}


//void presentation()  {
//  sendSketchInfo("RFID Lock", "1.0");
//  present(CHILD_ID, S_LOCK);
//}

void before() {
  // Make sure MFRC is disabled from the SPI bus
  pinMode(RST_PIN, OUTPUT);
  digitalWrite(RST_PIN, LOW);
  pinMode(SS_PIN, OUTPUT);
  digitalWrite(SS_PIN, LOW);
}

[gohan]

Tnx, I'll try in the next days.

Ps I edited your post with the correct tag for the code

[Aron Sjöberg]

Help!

I have a RFID RC522 module I'm trying to use instead of the PN532 NFC RFID Reader/Writer Module used in the RFID Lock Sensor example (https://www.mysensors.org/build/rfid).

I thought I could use the sketch above posted by @martins but I get the following error message. I'm a newbie so I don't really know what I'm doing wrong?

Arduino: 1.8.1 (Windows 10), Board: "Arduino Pro or Pro Mini, ATmega328 (5V, 16 MHz)"

Build options changed, rebuilding all
C:\Users\arons\Documents\Arduino\Vera_RFID-RC522\Vera_RFID-RC522.ino: In function 'int getID()':

Vera_RFID-RC522:259: error: return-statement with no value, in function returning 'int' [-fpermissive]

     return;

     ^

exit status 1
return-statement with no value, in function returning 'int' [-fpermissive]

[martins]

@Aron-Sjöberg said in RFID and NRF24L01 Wireless Network Coding Issues:

int getID()

Change that line in the getID() function to return 0;

[Plantex]

@martins

Could You please explain what do You mean by "Change that line in the getID() function to return 0;"

I am trying to run the sketch but I have the same problem as @Aron-Sjöberg.

Could You let me know which MFC library version I should use ?

[Ispandy]

Hi everyone,
I have problem on RFID sketch, when i scan the card its unlock the door but when i switch from openhab its not unlock.

the sketch is

/*
   --------------------------------------------------------------------------------------------------------------------
   Example sketch/program showing An Arduino Door Access Control featuring RFID, EEPROM, Relay
   --------------------------------------------------------------------------------------------------------------------
   This is a MFRC522 library example; for further details and other examples see: https://github.com/miguelbalboa/rfid
   This example showing a complete Door Access Control System
  Simple Work Flow (not limited to) :
                                     +---------+
  +----------------------------------->READ TAGS+^------------------------------------------+
  |                              +--------------------+                                     |
  |                              |                    |                                     |
  |                              |                    |                                     |
  |                         +----v-----+        +-----v----+                                |
  |                         |MASTER TAG|        |OTHER TAGS|                                |
  |                         +--+-------+        ++-------------+                            |
  |                            |                 |             |                            |
  |                            |                 |             |                            |
  |                      +-----v---+        +----v----+   +----v------+                     |
  |         +------------+READ TAGS+---+    |KNOWN TAG|   |UNKNOWN TAG|                     |
  |         |            +-+-------+   |    +-----------+ +------------------+              |
  |         |              |           |                |                    |              |
  |    +----v-----+   +----v----+   +--v--------+     +-v----------+  +------v----+         |
  |    |MASTER TAG|   |KNOWN TAG|   |UNKNOWN TAG|     |GRANT ACCESS|  |DENY ACCESS|         |
  |    +----------+   +---+-----+   +-----+-----+     +-----+------+  +-----+-----+         |
  |                       |               |                 |               |               |
  |       +----+     +----v------+     +--v---+             |               +--------------->
  +-------+EXIT|     |DELETE FROM|     |ADD TO|             |                               |
          +----+     |  EEPROM   |     |EEPROM|             |                               |
                     +-----------+     +------+             +-------------------------------+
   Use a Master Card which is act as Programmer then you can able to choose card holders who will granted access or not
 * **Easy User Interface**
   Just one RFID tag needed whether Delete or Add Tags. You can choose to use Leds for output or Serial LCD module to inform users.
 * **Stores Information on EEPROM**
   Information stored on non volatile Arduino's EEPROM memory to preserve Users' tag and Master Card. No Information lost
   if power lost. EEPROM has unlimited Read cycle but roughly 100,000 limited Write cycle.
 * **Security**
   To keep it simple we are going to use Tag's Unique IDs. It's simple and not hacker proof.
   @license Released into the public domain.
   Typical pin layout used:
   -----------------------------------------------------------------------------------------
               MFRC522      Arduino       Arduino   Arduino    Arduino          Arduino
               Reader/PCD   Uno/101       Mega      Nano v3    Leonardo/Micro   Pro Micro
   Signal      Pin          Pin           Pin       Pin        Pin              Pin
   -----------------------------------------------------------------------------------------
   RST/Reset   RST          9             5         D9         RESET/ICSP-5     RST
   SPI SS      SDA(SS)      10            53        D10        10               10
   SPI MOSI    MOSI         11 / ICSP-4   51        D11        ICSP-4           16
   SPI MISO    MISO         12 / ICSP-1   50        D12        ICSP-1           14
   SPI SCK     SCK          13 / ICSP-3   52        D13        ICSP-3           15
*/
#define MY_DEBUG
#define MY_RADIO_RF24
#define MY_NODE_ID 50

#include <SPI.h>        // RC522 Module uses SPI protocol
#include <MFRC522.h>  // Library for Mifare RC522 Devices
#include <MySensors.h>

/*
  Instead of a Relay you may want to use a servo. Servos can lock and unlock door locks too
  Relay will be used by default
*/
#define RFID 1

// #include <Servo.h>

/*
  For visualizing whats going on hardware we need some leds and to control door lock a relay and a wipe button
  (or some other hardware) Used common anode led,digitalWriting HIGH turns OFF led Mind that if you are going
  to use common cathode led or just seperate leds, simply comment out #define COMMON_ANODE,
*/

//#define COMMON_ANODE

#ifdef COMMON_ANODE
#define LED_ON LOW
#define LED_OFF HIGH
#else
#define LED_ON HIGH
#define LED_OFF LOW
#endif

#define redLed 4    // Set Led Pins
#define greenLed 5
#define blueLed 6

#define relay 2       // Set Relay Pin
#define wipeB 3     // Button pin for WipeMode

bool programMode = false;  // initialize programming mode to false

uint8_t successRead;    // Variable integer to keep if we have Successful Read from Reader

byte storedCard[4];   // Stores an ID read from EEPROM
byte readCard[4];   // Stores scanned ID read from RFID Module
byte masterCard[4];   // Stores master card's ID read from EEPROM
byte dumpedCard[4];

static const uint8_t MAGIC = 168;

// Create MFRC522 instance.
#define SS_PIN 8
#define RST_PIN 7
MFRC522 mfrc522(SS_PIN, RST_PIN);

void before() {
  // Make sure MFRC is disabled from the SPI bus
  pinMode(RST_PIN, OUTPUT);
  digitalWrite(RST_PIN, LOW);
  pinMode(SS_PIN, OUTPUT);
  digitalWrite(SS_PIN, LOW);
}

///////////////////////////////////////// Setup ///////////////////////////////////
void setup() {
   //Arduino Pin Configuration
  pinMode(redLed, OUTPUT);
  pinMode(greenLed, OUTPUT);
  pinMode(blueLed, OUTPUT);
  pinMode(wipeB, INPUT_PULLUP);   // Enable pin's pull up resistor
  pinMode(relay, OUTPUT);
  //Be careful how relay circuit behave on while resetting or power-cycling your Arduino
  digitalWrite(relay, HIGH);    // Make sure door is locked
  digitalWrite(redLed, LED_OFF);  // Make sure led is off
  digitalWrite(greenLed, LED_OFF);  // Make sure led is off
  digitalWrite(blueLed, LED_OFF); // Make sure led is off

  //Protocol Configuration
  Serial.begin(115200);  // Initialize serial communications with PC
  SPI.begin();           // MFRC522 Hardware uses SPI protocol
  mfrc522.PCD_Init();    // Initialize MFRC522 Hardware

  //If you set Antenna Gain to Max it will increase reading distance
  //mfrc522.PCD_SetAntennaGain(mfrc522.RxGain_max);

   Serial.println(F("Access Control v2.0"));   // For debugging purposes
  ShowReaderDetails();  // Show details of PCD - MFRC522 Card Reader details
  checkWipe();

  // Check if master card defined, if not let user choose a master card
  // This also useful to just redefine the Master Card
  // You can keep other EEPROM records just write other than MAGIC to EEPROM address 1
  // EEPROM address 1 should hold magical number which is 'MAGIC'
  if (loadState(1) != MAGIC) {
    Serial.println(F("No Master Card Defined"));
    Serial.println(F("Scan A PICC to Define as Master Card"));
    do {
      successRead = getID();            // sets successRead to 1 when we get read from reader otherwise 0
      digitalWrite(blueLed, LED_ON);    // Visualize Master Card need to be defined
      delay(200);
      digitalWrite(blueLed, LED_OFF);
      delay(200);
    }
    while (!successRead);                  // Program will not go further while you not get a successful read
    for ( uint8_t j = 0; j < 4; j++ ) {        // Loop 4 times
      saveState( 2 + j, readCard[j] );  // Write scanned PICC's UID to EEPROM, start from address 3
    }
    saveState(1, MAGIC);                  // Write to EEPROM we defined Master Card.
    Serial.println(F("Master Card Defined"));
  }
   Serial.println(F("-------------------"));
  Serial.println(F("Master Card's UID"));
  for ( uint8_t i = 0; i < 4; i++ ) {          // Read Master Card's UID from EEPROM
    masterCard[i] = loadState(2 + i);    // Write it to masterCard
    Serial.print(masterCard[i], HEX);
  }
  Serial.println("");
  Serial.println(F("-------------------"));
  Serial.println(F("Everything is ready"));
  Serial.println(F("Waiting PICCs to be scanned"));
  cycleLeds();    // Everything ready lets give user some feedback by cycling leds
} 

//////////////////////////////////////// MySensors Presentation ///////////////////////////////

MyMessage lockMsg(RFID, V_LOCK_STATUS);
void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("RFID PintuBesi", "1.0");
  present(RFID, S_LOCK);
}

///////////////////////////////////////// Main Loop ///////////////////////////////////
void loop () {
  do {
    successRead = getID();  // sets successRead to 1 when we get read from reader otherwise 0
    checkWipe();
    if (programMode) {
      cycleLeds();              // Program Mode cycles through Red Green Blue waiting to read a new card
    }
    else {
      normalModeOn();     // Normal mode, blue Power LED is on, all others are off
    }
  }
  while (!successRead);   //the program will not go further while you are not getting a successful read
  if (programMode) {
    if ( isMaster(readCard) ) { //When in program mode check First If master card scanned again to exit program mode
      Serial.println(F("Master Card Scanned"));
      Serial.println(F("Exiting Program Mode"));
      Serial.println(F("-----------------------------"));
      programMode = false;
      return;
    }
    else {
      if ( findID(readCard) ) { // If scanned card is known delete it
        Serial.println(F("I know this PICC, removing..."));
        deleteID(readCard);
        Serial.println("-----------------------------");
        Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      }
      else {                    // If scanned card is not known add it
        Serial.println(F("I do not know this PICC, adding..."));
        writeID(readCard);
        Serial.println(F("-----------------------------"));
        Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      }
    }
  }
  else {
    if ( isMaster(readCard)) {    // If scanned card's ID matches Master Card's ID - enter program mode
      programMode = true;
      Serial.println(F("Hello Master - Entered Program Mode"));
      uint8_t count = loadState(0);   // Read the first Byte of EEPROM that
      Serial.print(F("I have "));     // stores the number of ID's in EEPROM
      Serial.print(count);
      Serial.print(F(" record(s) on EEPROM"));
      Serial.println("");
      Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      Serial.println(F("Scan Master Card again to Exit Program Mode"));
      Serial.println(F("-----------------------------"));
    }
    else {
      if ( findID(readCard) ) { // If not, see if the card is in the EEPROM
        Serial.println(F("Welcome, You shall pass"));
        granted(300);         // Open the door lock for 300 ms
      }
      else {      // If not, show that the ID was not valid
        Serial.println(F("You shall not pass"));
        denied();
      }
    }
  }
}

/////////////////////////////////////////  Access Granted    ///////////////////////////////////
void granted ( uint16_t setDelay) {
  digitalWrite(blueLed, LED_OFF);   // Turn off blue LED
  digitalWrite(redLed, LED_OFF);  // Turn off red LED
  digitalWrite(greenLed, LED_ON);   // Turn on green LED
  digitalWrite(relay, LOW);     // Unlock door!
  send(lockMsg.set(false));
  delay(setDelay);          // Hold door lock open for given seconds
  digitalWrite(relay, HIGH);    // Relock door
  send(lockMsg.set(true));
  delay(1000);            // Hold green LED on for a second
}

///////////////////////////////////////// Access Denied  ///////////////////////////////////
void denied() {
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  digitalWrite(redLed, LED_ON);   // Turn on red LED
  delay(1000);
}


///////////////////////////////////////// Get PICC's UID ///////////////////////////////////
uint8_t getID() {
  // Getting ready for Reading PICCs
  if ( ! mfrc522.PICC_IsNewCardPresent()) { //If a new PICC placed to RFID reader continue
    return 0;
  }
  if ( ! mfrc522.PICC_ReadCardSerial()) {   //Since a PICC placed get Serial and continue
    return 0;
  }
  // There are Mifare PICCs which have 4 byte or 7 byte UID care if you use 7 byte PICC
  // I think we should assume every PICC as they have 4 byte UID
  // Until we support 7 byte PICCs
  Serial.println(F("Scanned PICC's UID:"));
  for ( uint8_t i = 0; i < 4; i++) {  //
    readCard[i] = mfrc522.uid.uidByte[i];
    Serial.print(readCard[i], HEX);
  }
  Serial.println("");
  mfrc522.PICC_HaltA(); // Stop reading
  return 1;
}

void ShowReaderDetails() {
  // Get the MFRC522 software version
  byte v = mfrc522.PCD_ReadRegister(mfrc522.VersionReg);
  Serial.print(F("MFRC522 Software Version: 0x"));
  Serial.print(v, HEX);
  if (v == 0x91)
    Serial.print(F(" = v1.0"));
  else if (v == 0x92)
    Serial.print(F(" = v2.0"));
  else
    Serial.print(F(" (unknown),probably a chinese clone?"));
  Serial.println("");
  // When 0x00 or 0xFF is returned, communication probably failed
  if ((v == 0x00) || (v == 0xFF)) {
    Serial.println(F("WARNING: Communication failure, is the MFRC522 properly connected?"));
    Serial.println(F("SYSTEM HALTED: Check connections."));
    // Visualize system is halted
    digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
    digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
    digitalWrite(redLed, LED_ON);   // Turn on red LED
    while (true); // do not go further
  }
}

///////////////////////////////////////// Cycle Leds (Program Mode) ///////////////////////////////////
void cycleLeds() {
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  delay(200);
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  digitalWrite(blueLed, LED_ON);  // Make sure blue LED is on
  delay(200);
  digitalWrite(redLed, LED_ON);   // Make sure red LED is on
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  delay(200);
}

//////////////////////////////////////// Normal Mode Led  ///////////////////////////////////
void normalModeOn () {
  digitalWrite(blueLed, LED_ON);  // Blue LED ON and ready to read card
  digitalWrite(redLed, LED_OFF);  // Make sure Red LED is off
  digitalWrite(greenLed, LED_OFF);  // Make sure Green LED is off
  digitalWrite(relay, HIGH);    // Make sure Door is Locked
}

//////////////////////////////////////// Read an ID from EEPROM //////////////////////////////
void readID( uint8_t number ) {
  uint8_t start = (number * 4 ) + 2;    // Figure out starting position
  loadCard(start, storedCard);
}

///////////////////////////////////////// Add ID to EEPROM   ///////////////////////////////////
void writeID( byte a[] ) {
  if ( !findID( a ) ) {     // Before we write to the EEPROM, check to see if we have seen this card before!
    uint8_t num = loadState(0);     // Get the numer of used spaces, position 0 stores the number of ID cards
    uint8_t start = ( num * 4 ) + 6;  // Figure out where the next slot starts
    num++;                // Increment the counter by one
    saveState( 0, num );     // Write the new count to the counter
    //for ( uint8_t j = 0; j < 4; j++ ) {   // Loop 4 times
    //  saveState( start + j, a[j] );  // Write the array values to EEPROM in the right position
    //}
    saveCard(start, a);
    successWrite();
    Serial.println(F("Succesfully added ID record to EEPROM"));
  }
  else {
    failedWrite();
    Serial.println(F("Failed! There is something wrong with ID or bad EEPROM"));
  }
}
///////////////////////////////////////// Remove ID from EEPROM   ///////////////////////////////////
void deleteID( byte a[] ) {
  if ( !findID( a ) ) {     // Before we delete from the EEPROM, check to see if we have this card!
    failedWrite();      // If not
    Serial.println(F("Failed! There is something wrong with ID or bad EEPROM"));
  }
  else {
    uint8_t num = loadState(0);   // Get the numer of used spaces, position 0 stores the number of ID cards
    uint8_t slot;       // Figure out the slot number of the card
    uint8_t start;      // = ( num * 4 ) + 6; // Figure out where the next slot starts
    uint8_t looping;    // The number of times the loop repeats
    uint8_t j;
    uint8_t count = loadState(0); // Read the first Byte of EEPROM that stores number of cards
    slot = findIDSLOT( a );   // Figure out the slot number of the card to delete
    start = (slot * 4) + 2;
    looping = ((num - slot) * 4);
    num--;      // Decrement the counter by one
    saveState( 0, num );   // Write the new count to the counter
    for ( j = 0; j < looping; j++ ) {         // Loop the card shift times
      saveState( start + j, loadState(start + 4 + j));   // Shift the array values to 4 places earlier in the EEPROM
    }
    for ( uint8_t k = 0; k < 4; k++ ) {         // Shifting loop
      saveState( start + j + k, 0);
    }
    successDelete();
    Serial.println(F("Succesfully removed ID record from EEPROM"));
  }
}

///////////////////////////////////////// Check Bytes   ///////////////////////////////////
bool checkTwo ( byte a[], byte b[] ) {   
  for ( uint8_t k = 0; k < 4; k++ ) {   // Loop 4 times
    if ( a[k] != b[k] ) {     // IF a != b then false, because: one fails, all fail
       return false;
    }
  }
  return true;  
}

///////////////////////////////////////// Find Slot   ///////////////////////////////////
uint8_t findIDSLOT( byte find[] ) {
  uint8_t count = loadState(0);       // Read the first Byte of EEPROM that
  for ( uint8_t i = 1; i <= count; i++ ) {    // Loop once for each EEPROM entry
    readID(i);                // Read an ID from EEPROM, it is stored in storedCard[4]
    if ( checkTwo( find, storedCard ) ) {   // Check to see if the storedCard read from EEPROM
      // is the same as the find[] ID card passed
      return i;         // The slot number of the card
    }
  }
}

///////////////////////////////////////// Find ID From EEPROM   ///////////////////////////////////
bool findID( byte find[] ) {
  uint8_t count = loadState(0);     // Read the first Byte of EEPROM that
  for ( uint8_t i = 1; i <= count; i++ ) {    // Loop once for each EEPROM entry
    readID(i);          // Read an ID from EEPROM, it is stored in storedCard[4]
    if ( checkTwo( find, storedCard ) )    // Check to see if the storedCard read from EEPROM
      return true;
      }
  return false;
}

///////////////////////////////////////// Write Success to EEPROM   ///////////////////////////////////
// Flashes the green LED 3 times to indicate a successful write to EEPROM
void successWrite() {
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is on
  delay(200);
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  delay(200);
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  delay(200);
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  delay(200);
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  delay(200);
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  delay(200);
}

///////////////////////////////////////// Write Failed to EEPROM   ///////////////////////////////////
// Flashes the red LED 3 times to indicate a failed write to EEPROM
void failedWrite() {
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  delay(200);
  digitalWrite(redLed, LED_ON);   // Make sure red LED is on
  delay(200);
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  delay(200);
  digitalWrite(redLed, LED_ON);   // Make sure red LED is on
  delay(200);
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  delay(200);
  digitalWrite(redLed, LED_ON);   // Make sure red LED is on
  delay(200);
}

///////////////////////////////////////// Success Remove UID From EEPROM  ///////////////////////////////////
// Flashes the blue LED 3 times to indicate a success delete to EEPROM
void successDelete() {
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  delay(200);
  digitalWrite(blueLed, LED_ON);  // Make sure blue LED is on
  delay(200);
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  delay(200);
  digitalWrite(blueLed, LED_ON);  // Make sure blue LED is on
  delay(200);
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  delay(200);
  digitalWrite(blueLed, LED_ON);  // Make sure blue LED is on
  delay(200);
}

////////////////////// Check readCard IF is masterCard   ///////////////////////////////////
// Check to see if the ID passed is the master programing card
bool isMaster( byte test[] ) {
  return checkTwo(test, masterCard);
}

bool monitorWipeButton(uint32_t interval) {
  uint32_t now = (uint32_t)millis();
  while ((uint32_t)millis() - now < interval)  {
    // check on every half a second
    if (((uint32_t)millis() % 500) == 0) {
      if (digitalRead(wipeB) != LOW)
        return false;
    }
  }
  return true;
}

void saveCard(uint8_t startPos, byte *card) {
  for ( uint8_t j = 0; j < 4; j++ ) {        // Loop 4 times
    saveState( startPos + j, card[j] );  // Write scanned PICC's UID to EEPROM, start from address 3
  }
}

void loadCard(uint8_t startPos, byte *card) {
  for ( uint8_t i = 0; i < 4; i++ )    // Read Card's UID from EEPROM
    card[i] = loadState(startPos + i);    // Write it to the card
}

void checkWipe() {
  //Wipe Code - If the Button (wipeB) Pressed while setup run (powered on) it wipes EEPROM
  if (digitalRead(wipeB) == LOW) {  // when button pressed pin should get low, button connected to ground
    digitalWrite(redLed, LED_ON); // Red Led stays on to inform user we are going to wipe
    Serial.println(F("Wipe Button Pressed"));
    Serial.println(F("You have 10 seconds to Cancel"));
    Serial.println(F("This will be remove all records and cannot be undone"));
    bool buttonState = monitorWipeButton(10000); // Give user enough time to cancel operation
    if (buttonState == true && digitalRead(wipeB) == LOW) {    // If button still be pressed, wipe EEPROM
      Serial.println(F("Starting Wiping EEPROM"));
       Serial.println(F("Starting Wiping"));
      saveState(0, 0 );     // light wipe. only erase number
      saveState(1, 0);      // light wipe. only erase magic number
      Serial.println(F("EEPROM Successfully Wiped"));
      digitalWrite(redLed, LED_OFF);  // visualize a successful wipe
      delay(200);
      digitalWrite(redLed, LED_ON);
      delay(200);
      digitalWrite(redLed, LED_OFF);
      delay(200);
      digitalWrite(redLed, LED_ON);
      delay(200);
      digitalWrite(redLed, LED_OFF);
    }
    else {
      Serial.println(F("Wiping Cancelled")); // Show some feedback that the wipe button did not pressed for 15 seconds
      digitalWrite(redLed, LED_OFF);
    }
  }
}


void receive(const MyMessage &message)
{
  if (message.type == V_LOCK_STATUS) {
    // Change relay state
      if (!message.getBool()) {
      granted(300);
    }
    }
}

need advise, thanks
regards

[evb]

@mfalkvidd, should this not be better receive it's own topic?

@Ispandy, does your node receives the message from openhab?
Change the code in the receive method to be able to serial print debug messages. Maybe openhab is not using the correction message type...

[Ispandy]

@evb, thank you for the reply
In that sketch above the node doesn't receive message from openhab, but the other node using same message type "message.type == V_LOCK_STATUS" it does receive message from openhab.

[evb]

@Ispandy are you now speaking about 2 nodes?

In that sketch above the node doesn't receive message from openhab
Did you add serial prints to be sure you don't receive anything. May you receive messages but not of the type V_LOCK_STATUS.

You should explain more in detail how your setup is done, because for me it isn't clear

[Ispandy]

@evb yes i have 2 nodes (node 3 and node 50) all with MRFC522 right now, the node 3 is working perfectly but i dont like add and remove card system, I just want to change the part of the RFID sketch on node 3 using the sketch above, so i make one node for test (node 50) and put the code

send(lockMsg.set(false));

and

send(lockMsg.set(true));

to this

void granted ( uint16_t setDelay) {
  digitalWrite(blueLed, LED_OFF);   // Turn off blue LED
  digitalWrite(redLed, LED_OFF);  // Turn off red LED
  digitalWrite(greenLed, LED_ON);   // Turn on green LED
  digitalWrite(relay, LOW);     // Unlock door!
  send(lockMsg.set(false));
  delay(setDelay);          // Hold door lock open for given seconds
  digitalWrite(relay, HIGH);    // Relock door
  send(lockMsg.set(true));
  delay(1000);            // Hold green LED on for a second
}

and i add this to node 50

if (message.type == V_LOCK_STATUS) {
    // Change relay state
    if (!message.getBool()) {
      granted(300);
    }

    // Write some debug info
    Serial.print(F("Lock status: "));
    Serial.println(message.getBool());
  }
    else
    {
      // Write some debug info
      Serial.print(F("Incoming msg type: "));
      Serial.print(message.type);
      Serial.print(F(" id: "));
      Serial.print(message.sensor);
      Serial.print(F(" content: "));
      Serial.println(message.getInt());
    }

nothing happen...

sketch Node 3

/
// Enable debug prints
#define MY_DEBUG
#define MY_NODE_ID 3
// Enable and select radio type attached
#define MY_RADIO_RF24
//#define MY_RF24_CHANNEL  10 
#include <MySensors.h>
#include <SPI.h>
#include <MFRC522.h> 
#include <Bounce2.h>

#define RF_INIT_DELAY   125
#define ONE_SEC         1000
#define MAX_CARDS       18
#define PROG_WAIT       10
#define HEARTBEAT       10
#define BAUD            115200

/*Pin definitions*/
#define LED_PIN         4
#define GARAGEPIN       2
#define SWITCH_PIN      3
#define RST_PIN   7   //  MFRC 
#define SS_PIN    8   //  MFRC 

MFRC522      mfrc522(SS_PIN, RST_PIN);  // Create MFRC522 instance
MFRC522::Uid olduid;
MFRC522::Uid masterkey = { 4,{ 0xEF,0xDB,0x8E,0x79 },0 };

byte       countValidCards = 0;
MFRC522::Uid validCards[MAX_CARDS];

void       ShowCardData(MFRC522::Uid* uid);
bool       sameUid(MFRC522::Uid* old, MFRC522::Uid* check);
void       copyUid(MFRC522::Uid* src, MFRC522::Uid* dest);
bool       isValidCard(MFRC522::Uid* uid);
int        releasecnt = 0;

//#define    CHILD_ID_ALARM    2
#define    CHILD_ID_LOCK     1
Bounce     debouncer = Bounce();

int        oldSwitchValue = -1;
int        switchValue = 0;
long       timer = -1;
bool       programmode = false;
bool       ledon;
int        programTimer = 0;
bool       armed = true;
unsigned long lastTime = 0;

MyMessage  lockMsg(CHILD_ID_LOCK, V_LOCK_STATUS);
//MyMessage  lockArmMsg(CHILD_ID_ALARM, V_ARMED);
//MyMessage  wrongMsg(CHILD_ID_ALARM, V_TRIPPED);

void before() {
  // Make sure MFRC is disabled from the SPI bus
  pinMode(RST_PIN, OUTPUT);
  digitalWrite(RST_PIN, LOW);
  pinMode(SS_PIN, OUTPUT);
  digitalWrite(SS_PIN, LOW);
}

void presentation() {
  sendSketchInfo("RFID Garage", "1.1"); delay(RF_INIT_DELAY);
  // Register all sensors to gw (they will be created as child devices)

  present(CHILD_ID_LOCK, S_LOCK);      delay(RF_INIT_DELAY);
  //present(CHILD_ID_ALARM, S_MOTION);   delay(RF_INIT_DELAY);
}

void setup() {
  Serial.begin(BAUD);   // Initialize serial communications with the PC
  pinMode(GARAGEPIN, OUTPUT);     // Initialise in/output ports

                  // Make sure MFRC will be disabled on the SPI bus
  /*pinMode(RST_PIN, OUTPUT);
  digitalWrite(RST_PIN, LOW);
  pinMode(SS_PIN, OUTPUT);
  digitalWrite(SS_PIN, LOW);*/

  pinMode(LED_PIN, OUTPUT);
  digitalWrite(LED_PIN, LOW);
  // Setup the button
  pinMode(SWITCH_PIN, INPUT);
  // Activate internal pull-up
  digitalWrite(SWITCH_PIN, HIGH);

  // After setting up the button, setup debouncer
  debouncer.attach(SWITCH_PIN);
  debouncer.interval(5);

  // Init mysensors library
  
  /*sendSketchInfo("RFID Garage", "1.1"); delay(RF_INIT_DELAY);

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID_LOCK, S_LOCK);      delay(RF_INIT_DELAY);
  present(CHILD_ID_ALARM, S_MOTION);   delay(RF_INIT_DELAY);*/

  recallEeprom();

  // Init MFRC RFID sensor
  SPI.begin();      // Init SPI bus
  mfrc522.PCD_Init();   // Init MFRC522
  ShowReaderDetails();          // Show details of PCD - MFRC522 Card Reader details

  //send(lockArmMsg.set(armed));
  Serial.println(F("Init done..."));
}

void loop() {
  timer++;
  delay(HEARTBEAT);
  debouncer.update();

  // Get the update value
  int switchValue = debouncer.read();
  if (switchValue != oldSwitchValue) {
    // Send in the new value
    Serial.print(F("Switch "));
    Serial.println(switchValue);

    if (switchValue && programmode) {
      lastTime = millis() / 1000;
    }

    if (!switchValue && programmode && lastTime > 0) {
      if ((millis() / 1000) - lastTime > 3) {
        Serial.println(F("Reset all cards"));
        countValidCards = 0;
        blinkFast(50);
      }
      else {
        Serial.println(F("Program off"));
        digitalWrite(LED_PIN, LOW);
        programmode = false;

        storeEeprom();
      }
    }

    if (!switchValue) {
      programTimer = 0;
    }
    oldSwitchValue = switchValue;
  }

  if (programmode && ((timer % (ONE_SEC / HEARTBEAT)) == 0)) {
    ledon = !ledon;
    digitalWrite(LED_PIN, ledon);
    programTimer++;

    // Stop program mode after 20 sec inactivity
    if (programTimer > PROG_WAIT) {
      programmode = false;
      digitalWrite(LED_PIN, false);
      Serial.println(F("Program expired"));
    }
  }

  if ((timer % (200 / HEARTBEAT)) == 0) {
    // Look for new cards
    if (!mfrc522.PICC_IsNewCardPresent()) {
      if (releasecnt > 0) {
        releasecnt--;
        if (!releasecnt) {
          olduid.size = 0;
          Serial.println(F("release"));
        }
      }
      return;
    }
    releasecnt = 5;

    // Select one of the cards
    if (!mfrc522.PICC_ReadCardSerial()) {
      return;
    }

    // Dump debug info about the card; PICC_HaltA() is automatically called
    //mfrc522.PICC_DumpToSerial(&(mfrc522.uid));
    if (!olduid.size || !sameUid(&(mfrc522.uid), &olduid)) {
      ShowCardData(&(mfrc522.uid));
      copyUid(&(mfrc522.uid), &olduid);
      if (isValidCard(&olduid)) {
        OpenDoor(false);
      }
      else {

        if (sameUid(&(mfrc522.uid), &masterkey)) {
          // Only switch in program mode when mastercard is found AND the program button is pressed
          if (switchValue) {
            Serial.println(F("Program mode"));
            programmode = true;
            programTimer = 0;
            lastTime = 0;
          }
        }
        else {
          if (programmode) {
            Serial.println(F("new card"));
            programTimer = 0;

            if (countValidCards < MAX_CARDS)
            {
              // Add card to list...
              copyUid(&(mfrc522.uid), &validCards[countValidCards]);
              countValidCards++;
              blinkFast(15);
            }
          }
          else {
            Serial.println(F("Invalid card"));
            //if (armed) {
             // send(wrongMsg.set(1));
             // delay(2000);
              //send(wrongMsg.set(0));
            //}
          }
        }
      }
    }
  }
}

void ShowCardData(MFRC522::Uid* uid) {
  Serial.print(F("Card UID:"));
  for (byte i = 0; i < uid->size; i++) {
    if (uid->uidByte[i] < 0x10) {
      Serial.print(F(" 0"));
    }
    else {
      Serial.print(F(" "));
    }
    Serial.print(uid->uidByte[i], HEX);
  }
  Serial.println();
}

void copyUid(MFRC522::Uid* src, MFRC522::Uid* dest)
{
  dest->size = src->size;
  dest->sak = src->sak;

  for (byte i = 0; i < src->size; i++) {
    dest->uidByte[i] = src->uidByte[i];
  }
}

bool sameUid(MFRC522::Uid* old, MFRC522::Uid* check)
{
  if (old->size != check->size) {
    return false;
  }
  for (byte i = 0; i < old->size; i++) {
    if (old->uidByte[i] != check->uidByte[i]) {
      return false;
    }
  }
  return true;
}

bool isValidCard(MFRC522::Uid* uid)
{
  for (byte i = 0; i < countValidCards; i++) {
    if (validCards[i].size != uid->size) {
      break;
    }
    for (int j = 0; j < uid->size; j++) {
      if (validCards[i].uidByte[j] != uid->uidByte[j]) {
        break;
      }
      if (j == (uid->size - 1)) {
        return true;
      }
    }
  }
  return false;
}


void storeEeprom()
{
  byte address = 0;
  saveState(address++, countValidCards);

  for (byte i = 0; i < countValidCards; i++) {
    saveState(address++, validCards[i].size);
    for (byte j = 0; j < 10; j++) {
      saveState(address++, validCards[i].uidByte[j]);
    }
  }
}

void recallEeprom()
{
  byte address = 0;

  countValidCards = loadState(address++);
  if (countValidCards > MAX_CARDS) {
    Serial.println(F("Not a valid EEPROM reading set to default"));
    countValidCards = 0;
    storeEeprom();
    return;
  }

  for (byte i = 0; i < countValidCards; i++) {
    validCards[i].size = loadState(address++);
    for (byte j = 0; j < 10; j++) {
      validCards[i].uidByte[j] = loadState(address++);
    }
  }

}

void blinkFast(int times)
{
  for (int i = 0; i < times; i++) {
    ledon = !ledon;
    digitalWrite(LED_PIN, ledon);
    delay(100);
  }
}

void OpenDoor(bool fakeOpen)
{
  Serial.println(F("Open door!"));
  send(lockMsg.set(false));

  if (!fakeOpen) {
    digitalWrite(LED_PIN, HIGH);
    digitalWrite(GARAGEPIN, HIGH);
  }
  
  delay(1000);

  if (!fakeOpen) {
    digitalWrite(GARAGEPIN, LOW);
    digitalWrite(LED_PIN, LOW);
  }

  send(lockMsg.set(true));
}

void ShowReaderDetails() {
  // Get the MFRC522 software version
  byte v = mfrc522.PCD_ReadRegister(mfrc522.VersionReg);
  Serial.print(F("MFRC522 Software Version: 0x"));
  Serial.print(v, HEX);
  if (v == 0x91) {
    Serial.print(F(" = v1.0"));
  }
  else if (v == 0x92) {
    Serial.print(F(" = v2.0"));
  }
  else {
    Serial.print(F(" (unknown)"));
  }
  Serial.println("");

  // When 0x00 or 0xFF is returned, communication probably failed
  if ((v == 0x00) || (v == 0xFF)) {
    Serial.println(F("WARNING: Communication failure, is the MFRC522 properly connected?"));
  }
}


void receive(const MyMessage &message)
{
  if (message.type == V_LOCK_STATUS) {
    // Change relay state
    if (!message.getBool()) {
      OpenDoor(false);
    }

    // Write some debug info
    Serial.print(F("Lock status: "));
    Serial.println(message.getBool());
  }
  /*else
  {
    if (message.type == V_ARMED) {
      // Change relay state
      armed = message.getBool();

      // Write some debug info
      Serial.print(F("Arm status: "));
      Serial.println(message.getBool());
    }*/
    else
    {
      // Write some debug info
      Serial.print(F("Incoming msg type: "));
      Serial.print(message.type);
      Serial.print(F(" id: "));
      Serial.print(message.sensor);
      Serial.print(F(" content: "));
      Serial.println(message.getInt());
    }
  }
//}

I'm not good at programming that's why I'm asking for help:expressionless: :expressionless:

[evb]

@Ispandy what happens if you download the same sketch from the working node 3 tot your new node 50?
Adapt of course the node-id!

If it works we can exclude a hardware problem, then it must be a software problem.
In that last case, we can check your sketch more deeply.

[Ispandy]

@evb thank you for the response, and sorry for late reply.
As I mentioned above, that node 3 is running as it should, and I've copied it to node 50 and it's also running normally. The problem is on sketch node 50 when i click the switch in openhab the relay doesn't respond but when i scan the card on rfid, the relay responds. Unlike node 3, the relay responds to both card scans and openhab.
Regards,

[evb]

@Ispandy, let resume some things because I'm lost

You copied the sketch code from node 3 (= correctly running node with cardscans and remote control from openhab) to node 50 and you adapted the node id.
This same sketch on node 50 is running correctly with cardscans but not with openhab? Correct?

If above is correct: somewhere your openhab configuration for this node 50 is not correct. You say that node 50 is never receiving the openhab command, so there is a problem with your openhab configuration for node 50.