💬 Button size radionode
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
-
I'm revising my earlier comment. Based on new experience, I wouldn't recommend using the smaller atmega328p.
-
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
-
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
@bjornhallberg said:
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
You can find these modules as "rfm69hc" on Ali. Do not forget about haggling :)
I've received new version of these little boards :smiley:
Will show new soldered boards asap. -
Next revision :smirk:
-
Looks perfect with new usb-ttl. :smiley: I plan to use this configuration as RFM69-USB gateway.
-
All my rfm69 boards family are under tests now :smiley:
-
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
@Cliff-Karlsson said:
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
I will try to estimate rough prices for all boards today.
-
So I am ready to present estimated prices to all my new boards.
The estimate is too rough because I am not sure about size of the production batch. But it's better than nothing. Prices include pcb's, components and assembly. Configurations are not fully accepted yet.---WALL SOCKET INSERTABLE NODE
BASIC (ac/dc, atmega, rfm69, 10a relay) - 9.5$
ADVANCED (ac/dc, atmega, rfm69, 10a relay, current sensor, rgb led) - 10.8$
MAX (ac/dc, atmega, rfm69, 10a relay, currrent sensor, atsha204, watchdog, rgb led) - 12.2$---WALL SWITCH INSERTABLE NODE
BASIC (atmega, rfm69, buttons controller, JST wires) - 6.5$
MAX (atmega, rfm69, buttons controller, JST wires, atsha204) - 7.5$--BUTTON SIZE RADIO NODE
BASIC (atmega, rfm69) - 6$
MAX (atmega, rfm69, atsha204) - 7$--SECRET TTL-USB
BASIC - 1.4$ -
Ahh Great, I will be ordering a lot of boards when they are available. Just one question, do you have any sensor-boards planned? like PIR/temp/hum/Lux -multisensor ?
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
-
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
-
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
@Cliff-Karlsson said:
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
Unfortunately I have no time. Now i'm focusing on preparing three boards for mass production. Do not forget, I have job and I design those boarsd in my free time. May be I will design sensors boards after :smiley:
-
@Koresh not really for me as I have enough boards :laughing: but i was just thinking.. it's a button size node, so is it a for a button :) or a coincell node? If it's a button size, so which batt do you use? I guess a coincell, or I don't see other advantage of the size except price. If it's a coincell node, do you have few capa at input to buffer and prevent internal res?
Ideas only :)
@Cliff-Karlsson don't worry i will release my multisensors stuff, with pcba. Not my job too, and lot of other boards so.. But sure that won't be a 7 euros board. You can't have so much sensors for this price with radios etc..or maybe @Koresh has some magics :) LOL
