💬 Button size radionode
-
Looks perfect with new usb-ttl. :smiley: I plan to use this configuration as RFM69-USB gateway.
-
All my rfm69 boards family are under tests now :smiley:
-
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
@Cliff-Karlsson said:
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
I will try to estimate rough prices for all boards today.
-
So I am ready to present estimated prices to all my new boards.
The estimate is too rough because I am not sure about size of the production batch. But it's better than nothing. Prices include pcb's, components and assembly. Configurations are not fully accepted yet.---WALL SOCKET INSERTABLE NODE
BASIC (ac/dc, atmega, rfm69, 10a relay) - 9.5$
ADVANCED (ac/dc, atmega, rfm69, 10a relay, current sensor, rgb led) - 10.8$
MAX (ac/dc, atmega, rfm69, 10a relay, currrent sensor, atsha204, watchdog, rgb led) - 12.2$---WALL SWITCH INSERTABLE NODE
BASIC (atmega, rfm69, buttons controller, JST wires) - 6.5$
MAX (atmega, rfm69, buttons controller, JST wires, atsha204) - 7.5$--BUTTON SIZE RADIO NODE
BASIC (atmega, rfm69) - 6$
MAX (atmega, rfm69, atsha204) - 7$--SECRET TTL-USB
BASIC - 1.4$ -
Ahh Great, I will be ordering a lot of boards when they are available. Just one question, do you have any sensor-boards planned? like PIR/temp/hum/Lux -multisensor ?
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
-
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
-
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
@Cliff-Karlsson said:
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
Unfortunately I have no time. Now i'm focusing on preparing three boards for mass production. Do not forget, I have job and I design those boarsd in my free time. May be I will design sensors boards after :smiley:
-
@Koresh not really for me as I have enough boards :laughing: but i was just thinking.. it's a button size node, so is it a for a button :) or a coincell node? If it's a button size, so which batt do you use? I guess a coincell, or I don't see other advantage of the size except price. If it's a coincell node, do you have few capa at input to buffer and prevent internal res?
Ideas only :)
@Cliff-Karlsson don't worry i will release my multisensors stuff, with pcba. Not my job too, and lot of other boards so.. But sure that won't be a 7 euros board. You can't have so much sensors for this price with radios etc..or maybe @Koresh has some magics :) LOL
-
@Cliff-Karlsson said:
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
Unfortunately I have no time. Now i'm focusing on preparing three boards for mass production. Do not forget, I have job and I design those boarsd in my free time. May be I will design sensors boards after :smiley:
-
@NeverDie said:
@Koresh
What's your estimate as to when you'll have it manufactured and ready to ship?This week will collect components. Next week PCB production and PCBA. After that another week to ship few samples for testing. If All goes well after 3-4 weeks from now- ready to ship them from China.
-
Any update to the ETA?
-
I became a father yesterday :baby: My pcb contractor gave us very many fails with my last orders... So we have a little delay. I will try to say ETA asap.
