💬 Relay

[pepson]

Can you show converted sketch with 2 buttons and 2 relays ? I dont know how convert this sketch bersion with buttons...

[Boots33]

@pepson Have a look at this thread for some ideas to get you started.

[fdojurado]

I would like to ask about ack. Does the library have a specific timeout? Does the library resends the message when ack is not received? Thank you.

[Puneit Thukral]

Cam I use an arduino pro mini 3.3V 8 Mhz to trigger the relay - or do I need a 5v arduino?

[sundberg84]

@Puneit-Thukral - it depends on the relay.
If you read the datasheet for intended relay you will see what is needed. Most relays i have seen requiers 5v and a good current (which Arduino sometimes fail to deliver).

[Puneit Thukral]

@sundberg84 I used a 3904 transistor between the relay and arduino and it works just fine with 3.3 V Arduino pro mini 8 HMz.
(2N2222 also works, but I have many pieces of 3904 and just a few 2N2222, hence using 3904)

[Javier Rubio]

I have my gateway and my relay, I believe is working fine, I just want to know what set of caracters do I need to send in the serial monitor to turn on the relay? I will like to use the info in order to use a controller like Vantage or C4, is that possible? Regards

[Puneit Thukral]

@Javier-Rubio I m not an expert- a complete novice.
I would suggest one of the following - trigger the relay through a controller or use one the the arduino relay example sketch in which relay is programmed to turn on and off every 1 second. This would help you validate if your wiring is correct or not.

[Gizmoh]

I tried the relay sketch on my arduino mini pro (5v), step down converter for the NRF module and a two channel relay. It's conecte to a Raspi GW wirh the 2.0.0 beta and FHEM as controller. The switching works as expexted. but the relay switches continuisly on and off on its own after a certain time. I tried removing the loop-block but with no effort. Is there anything i can do to get a stable state? Thanks

[korttoma]

@Gizmoh sounds like the relays are not receiving enough power to remain on. How are you powering all this?

[Gizmoh]

@korttoma
I'm powering this with 6 x AA Batteries into the RAW Input from the Arduino and the 5v output from Arduino to the Relay.

[korttoma]

@Gizmoh ok so it seems like the voltage regulator on the arduino cannot handle the load the relays produce when activated. You need to power the relay board directly from your batteries either trough another 5V regulator or if your relay board already can handle a higher voltage you can connect it directly.

[Gizmoh]

@korttoma Ah, okay, thank you. I'll give it a try.
Maybe connecting a Decoupling-Capacitor could also fix this problem?

[Rodolfo Vieira]

hello one doubt
if a use this sketch: /mysensors/MySensorsArduinoExamples/examples/RelayWithButtonActuator/RelayWithButtonActuator.ino

when i press the button home assistant knows if switch was turned or off? its change the stat?

[riochicken]

Hi,

First of all Merry Xmas to all of you!

I want to use this sketch with three LEDs to present the status of the alarm at home, so with a multicolored LED I have a green status, a red and a blue status, but I just want one color at a time, is there a way to alter the code a little to make sure that is a color is activated, the other one is turned off?

[mfalkvidd]

@riochicken yes, but I wouldn't recommend relays for controlling a led. It can be controlled directly from the Arduino pins.

Look at the code for these:
https://www.openhardware.io/view/21/RGBW-LED-Controller#tabs-source
https://www.openhardware.io/view/74/OH-MySensors-RGBW-Controller#tabs-source

[riochicken]

@mfalkvidd : I have directly soldered the LED's to the board, would be a waste of relays.. :) Thanks I will look into the examples you just gave...

[riochicken]

@mfalkvidd I have no clue how to decode the examples you gave, normally in vb or powershell I would check if a pin would be active if another color was requested so I could turn off the other color but I am a bit lost with the code....

[pepson]

Hi all
I use this sketch for controlling 2 x relays. Can anybody change me this sketch to controliling only 1 x relay ?

Next problem....
Anybody know how edit sketch for relays to add itrms to send repeate update status to gateway? I want eliminate problem when node start and change status , but gateway is disabled. And after gateway will be enable show in my Domoticz old status/last memory before disable gateway. But after this node has changed status and this status is not show in Domoticz after run. I want to work it as Z-Wave. Z-wave has always actual status. Is any chance to also MySensors Gateway and not has always actual status ?

/**
   DESCRIPTION
   Sketch for 2x relay with buttons monostable. After back power all relays set OFF and send correct status OFF to controller.  
*/

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_868MHZ
#define MY_IS_RFM69HW

// Enabled repeater feature for this node
#define MY_REPEATER_FEATURE

// Node id defaults to AUTO (tries to fetch id from controller)
#define MY_NODE_ID AUTO

#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

// Define Relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0  // GPIO value to write to turn off attached relay

// Define Sensor ID's
#define SSR_A_ID 1   // Id of the sensor child
#define SSR_B_ID 2   // Id of the sensor child

// Define buttons and relays
const int buttonPinA = 3;
const int buttonPinB = 4;
const int relayPinA = 5;
const int relayPinB = 6;

// Define Variables
int oldValueA = 0;
int oldValueB = 0;
bool stateA = false;
bool stateB = false;
int trigger = 0;

Bounce debouncerA = Bounce();
Bounce debouncerB = Bounce();

MyMessage msgA(SSR_A_ID, V_STATUS);
MyMessage msgB(SSR_B_ID, V_STATUS);

void setup()
{

  pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up
  pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up


  // After setting up the buttons, setup debouncer
  debouncerA.attach(buttonPinA);
  debouncerA.interval(5);
  debouncerB.attach(buttonPinB);
  debouncerB.interval(5);

  // Make sure relays are off when starting up
  digitalWrite(relayPinA, RELAY_OFF);
  digitalWrite(relayPinB, RELAY_OFF);
  // Then set relay pins in output mode
  pinMode(relayPinA, OUTPUT);
  pinMode(relayPinB, OUTPUT);

}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("2xRelay with monostable", "2.1");

  // Register all sensors to gw (they will be created as child devices)
  present(SSR_A_ID, S_LIGHT);
  present(SSR_B_ID, S_LIGHT);

}

/*
   Example on how to asynchronously check for new messages from gw
*/
void loop()
{
if (trigger == 0){
  send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off
  send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off
  trigger = 1;
}
  
  debouncerA.update();
  // Get the update value
  int valueA = debouncerA.read();
  if (valueA != oldValueA && valueA == 0) {
    send(msgA.set(stateA ? false : true), true); // Send new state and request ack back

  }
  oldValueA = valueA;
 

  debouncerB.update();
  // Get the update value
  int valueB = debouncerB.read();
  if (valueB != oldValueB && valueB == 0) {
    send(msgB.set(stateB ? false : true), true); // Send new state and request ack back

  }
  oldValueB = valueB;
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type == V_STATUS) {
      
    switch (message.sensor) {
      case 1:
        stateA = message.getBool();
        digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF);
        
        break;
      case 2:
        stateB = message.getBool();
        digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF);
        
        break;
      
    }
   
      // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.println(message.sensor);
    Serial.print("from node:");
    Serial.println(message.sender);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}```

[oufman]

Hello,
I would like to do an auto off after 2 sec directly in the sketch, however I do not understand how to write the code? I do not want to make a loop, but on pressing the ON button from my box the relay is activated is deactivated after 2 sec.

Thank you for your help.