not going in the void receive() function

[npiot]

Hi,
working on my sensors v2, IDE arduino 1.6.7
The sketch is working OK, and connects to my jeedom controller no problem.
I want to use the data received from node directly on my gateway to process it (jeedom is just here to record the data over time).

on my serial gateway sketch, I added a void receive( const Mymessage &message) {} fonction, and it seems the sketch is never going there, even when messages are received, as I can see in my serial console.

Any idea someone? Any help much appreciated.

// Enable debug prints to serial monitor
#define MY_DEBUG 


// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level. 
#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <SPI.h>
#include <MySensors.h>  
#include <DHT.h>

#define CHILD_ID_HUM 10
#define CHILD_ID_TEMP 11
#define HUMIDITY_SENSOR_DIGITAL_PIN 4  //data pin pour DHT

#define BUREAU_NODE_ID 1
#define GW_NODE_ID 0
#define DS18B20 0
#define THERM 17
#define TEMP_DHT 11
#define HRD_HT 10

float bureauds = 0, bureautherm =0, tempdht = 0, hrdht =0;

unsigned long SLEEP_TIME = 10000; // Sleep time between reads (in milliseconds)

DHT dht;
//float lastTemp;
//float lastHum;
boolean metric = true; 
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);

void setup() { 
  // Setup locally attached sensors
  Serial.begin(115200);
  Serial.println();
  Serial.println("Status\tHumidity (%)\tTemperature (C)\t(F)");

  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN); 
}

void presentation() {
  sendSketchInfo("GW Humidity/Temp", "1.0");
 // Present locally attached sensors 
  present(CHILD_ID_HUM, S_HUM);
  present(CHILD_ID_TEMP, S_TEMP);
}

void loop() { 
  // Send locally attached sensor data here 
  wait(dht.getMinimumSamplingPeriod());

float temperature = dht.getTemperature();
  if (isnan(temperature)) {
      Serial.println("Failed reading temperature from DHT");
  } else {
    send(msgTemp.set(temperature, 1));
    Serial.print("T: ");
    Serial.println(temperature);
  }

  float humidity = dht.getHumidity();
  if (isnan(humidity)) {
      Serial.println("Failed reading humidity from DHT");
  } else {
      send(msgHum.set(humidity, 1));
      Serial.print("H: ");
      Serial.println(humidity);
  }

 Serial.print("Dallas: ");
 Serial.println(bureauds);
 Serial.print("Therm: ");
 Serial.println(bureautherm);
 Serial.print("tempDHT: ");
 Serial.println(tempdht);
 Serial.print("HRDHT: ");
 Serial.println(hrdht);

  // Sleep until interrupt comes in on motion sensor. Send update every two minute. 
  //sleep(SLEEP_TIME);
  wait(SLEEP_TIME);
    
}


void receive(const MyMessage &message) {
  Serial.print("received something: ");
  Serial.println(message.sender, message.sensor);
  
  switch (message.sender) {
        case BUREAU_NODE_ID:
             switch (message.sensor){
                   case DS18B20:
                         bureauds = message.getFloat();
                  break; 
                  case THERM:
                         bureautherm = message.getFloat();
                  break;
          } 
          break; 
     case GW_NODE_ID:
             switch (message.sensor){
                  case TEMP_DHT:
                         tempdht = message.getFloat();
                  break; 
                  case HRD_HT:
                         hrdht = message.getFloat();
                  break; 
        } 
         break; 
  }
 Serial.print("Dallas: ");
 Serial.println(bureauds);
 Serial.print("Therm: ");
 Serial.println(bureautherm);
 Serial.print("tempDHT: ");
 Serial.println(tempdht);
 Serial.print("HRDHT: ");
 Serial.println(hrdht);
   
}

abstract from serial output when a message is received from node 1, with sensors 0 and 17 :
0;255;3;0;9;TSP:SANCHK:OK
0;11;1;0;0;25.4
T: 25.40
0;10;1;0;1;50.3
H: 50.30
Dallas: 0.00
Therm: 0.00
tempDHT: 0.00
HRDHT: 0.00
0;255;3;0;9;TSP:MSG:READ 1-1-0 s=0,c=1,t=0,pt=7,l=5,sg=0:24.5
1;0;1;0;0;24.5
0;255;3;0;9;TSP:MSG:READ 1-1-0 s=17,c=1,t=0,pt=7,l=5,sg=0:24.6
1;17;1;0;0;24.6
0;255;3;0;9;TSP:MSG:READ 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:94
1;255;3;0;0;94
0;255;3;0;9;TSP:MSG:READ 1-1-0 s=20,c=1,t=38,pt=7,l=5,sg=0:3.8
1;20;1;0;38;3.8
0;11;1;0;0;25.3
T: 25.30
0;10;1;0;1;50.2
H: 50.20
Dallas: 0.00
Therm: 0.00
tempDHT: 0.00
HRDHT: 0.00
0;11;1;0;0;25.3
T: 25.30
0;10;1;0;1;50.2
H: 50.20
Dallas: 0.00
Therm: 0.00
tempDHT: 0.00
HRDHT: 0.00

Thanks, Nicolas

[mfalkvidd]

This post is deleted!