DualOptiboot Bootloader (Solved)
-
Have you run basic tests against your flash, and checked that you are able to communicate with it? F. Ex with a test sketch, that tries to read the id of the flash.
Next step would be to setup the mysensors sketch, with Ota enabled. I haven't used it myself yet, as I usually just go around to all nodes and reprogram them manually (even though they are sensebender micros with onboard flash)
-
Hey, thanks for Respons...
how can i test it? I try this sketch but it is hanging around init. . .
/* |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| | Diagnostics.ino | | SPIFlash library | | v 2.4.0 | |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| | Marzogh | | 11.09.2016 | |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| | | | For a full diagnostics rundown - with error codes and details of the errors | | uncomment #define RUNDIAGNOSTIC in SPIFlash.cpp in the library before compiling | | and loading this application onto your Arduino. | | | |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| */ #include<SPIFlash.h> #include<SPI.h> #define WINBOND 0xEF #define MICROCHIP 0xBF char printBuffer[128]; SPIFlash flash; void setup() { Serial.begin(115200); Serial.print(F("Initialising Flash memory")); for (int i = 0; i < 10; ++i) { Serial.print(F(".")); } Serial.println(); flash.begin(); Serial.println(); Serial.println(); randomSeed(analogRead(A0)); getID(); diagnose(); } void loop() { } //~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~Serial Print Functions~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~// void clearprintBuffer() { for (uint8_t i = 0; i < 128; i++) { printBuffer[i] = 0; } } void printLine() { Serial.println(F("---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------")); } void printPass() { Serial.print(F("Pass")); } void printFail() { Serial.print(F("Fail")); } void printTab(uint8_t a, uint8_t b) { for (uint8_t i = 0; i < a; i++) { Serial.print(F("\t")); } if (b > 0) { Serial.print("||"); for (uint8_t i = 0; i < b; i++) { Serial.print(F("\t")); } } } void printTime(uint32_t _wTime, uint32_t _rTime) { printTab(2, 1); printTimer(_wTime); printTab(2, 1); printTimer(_rTime); } void printTimer(uint32_t _us) { if (_us > 1000000) { float _s = _us / (float)1000000; Serial.print(_s, 4); Serial.print(" s"); } else if (_us > 10000) { float _ms = _us / (float)1000; Serial.print(_ms, 4); Serial.print(" ms"); } else { Serial.print(_us); Serial.print(F(" us")); } }I use AT25DF512C-SSHN-B
-
Hangs around init, of which module?
What does the serial output tell you in that sketch?
There is one example here
https://github.com/mysensors/MySensorsArduinoExamples/blob/master/libraries/SPIFlash/examples/SPIFlash_ReadWrite/SPIFlash_ReadWrite.ino -
I found that Sketch now . . SPIFlash_ReadWrite.ino
Start...Init FAIL!I use AT25DF512C-SSHN-B
-
-
That works, i think ;-)
Init OK! Start...Init OK! Flash content: 0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0. Erasing Flash chip ... DONE DeviceID: 0But OTA does not work . . .
My Test-Sketch:
/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * DESCRIPTION * * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller * http://www.mysensors.org/build/temp */ // Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 #define MY_RF24_PA_LEVEL RF24_PA_MAX #define MY_BAUD_RATE 115200 #define MY_NODE_ID 50 #define MY_RF24_CHANNEL 105 #define MY_OTA_FIRMWARE_FEATURE #define MY_OTA_FLASH_SS 8 // EEprom CS pin //#define OTA_WAIT_PERIOD 300 //#define ATSHA204_PIN 12 // A3 Arduino Digital I/O pin number for ATSHA204A sot23 ic (for authentication) //#define MY_SIGNING_SOFT //#define MY_SIGNING_ATSHA204 //#define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0x09,0x08,0x07,0x06,0x05,0x04,0x03,0x02,0x01}}} //#define MY_SIGNING_REQUEST_SIGNATURES //#ifndef MY_SIGNING_SOFT_RANDOMSEED_PIN //#define MY_SIGNING_SOFT_RANDOMSEED_PIN 7 //#endif //#ifndef MY_SIGNING_ATSHA204_PIN //#define MY_SIGNING_ATSHA204_PIN 17 //#endif #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #include <OneWire.h> #define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 4 // Pin where dallase sensor is connected #define MAX_ATTACHED_DS18B20 16 unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds) OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. float lastTemperature[MAX_ATTACHED_DS18B20]; int numSensors=0; bool receivedConfig = false; bool metric = true; // Initialize temperature message MyMessage msg(0,V_TEMP); void before() { // Startup up the OneWire library sensors.begin(); } void setup() { // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Temperature Sensor", "1.1"); // Fetch the number of attached temperature sensors numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) { present(i, S_TEMP); } } void loop() { // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) //sleep(conversionTime); // Read temperatures and send them to controller for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) { // Fetch and round temperature to one decimal float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.; // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature != 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature,1)); // Save new temperatures for next compare lastTemperature[i]=temperature; } } }MYSController log Node 50:
21.10.2016 12:25:37 NODE New node discovered, node id=50 21.10.2016 12:25:37 CHILD New child discovered, node id=50, child id=internal 21.10.2016 12:25:37 INFO BL version=768 21.10.2016 12:25:37 INFO No FW assigned 21.10.2016 12:25:37 RX 50;255;4;0;0;0A000200B004B6D30300 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=3,t=15,pt=6,l=2,sg=0:0100 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=0,t=17,pt=0,l=5,sg=0:2.0.0 21.10.2016 12:25:37 DEBUG Update child id=255, type=ARDUINO_NODE 21.10.2016 12:25:37 RX 50;255;0;0;17;2.0.0 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0 21.10.2016 12:25:37 TX 50;255;3;0;6;M 21.10.2016 12:25:37 RX 50;255;3;0;6;0 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=6,pt=0,l=1,sg=0,ft=0,st=ok:M 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=3,t=11,pt=0,l=18,sg=0:Temperature Sensor 21.10.2016 12:25:37 RX 50;255;3;0;11;Temperature Sensor 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.1 21.10.2016 12:25:37 RX 50;255;3;0;12;1.1 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=0,c=0,t=6,pt=0,l=0,sg=0: 21.10.2016 12:25:37 CHILD New child discovered, node id=50, child id=0 21.10.2016 12:25:37 DEBUG Update child id=0, type=TEMP 21.10.2016 12:25:37 RX 50;0;0;0;6; 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=3,t=26,pt=1,l=1,sg=0:2 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=ok:1 21.10.2016 12:25:37 RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=0,c=1,t=0,pt=7,l=5,sg=0:25.3If i assigning new FW, following in log, but nothing happens . . ..
21.10.2016 12:28:43 INFO FW "Test02" assigned to node 50 21.10.2016 12:28:43 INFO Send FW info to node 50: type=A, version=2, blocks=0x04B0, CRC=0xD3B6 21.10.2016 12:28:43 TX 50;0;4;0;1;0A000200B004B6D3 21.10.2016 12:28:43 RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=0,c=4,t=1,pt=6,l=8,sg=0,ft=0,st=ok:0A000200B004B6D3 -
OK . . . The Upload is successful right now, dont know why but it works.
Now i have the Problem after transfer Data it stops at "Ongoing 100%" and nothing happens anymore. The Node needs Powercycle, Resetbutton has no effect.... (scalz Rollershutter HW)
-
Works right now. . . my faulty was to flash the first Programm with the wrong Bootloader. :rage:
-
why i told you to read the howto, because you would have burnt the right BL (sensebender in boards) ;)
great you got it working :) -
why i told you to read the howto, because you would have burnt the right BL (sensebender in boards) ;)
great you got it working :) -
I know but i had Trouble with the nrf is it pluged. I will try it again and give you a Feedback.
-
@Takero
why removing R14? then is avrspi still working?? it's a pull-up for CSN, and when you have multiple ic on SPI bus, it's good practice to have it, and avoid some dumb issue..it didn't work with R14?? perhaps.. -
I does not work again . . . i dont know why :-(
After Upload new Firmware, the device wont reboot and hanging in an bootloop.
Log from MYSController:
[2016-10-29 14:30:37.589 Info] RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=255,c=4,t=3,pt=6,l=22,sg=0,ft=0,st=ok:6400020001000C941F040C941F040C9409140C941F04 [2016-10-29 14:30:37.602 Info] RX 0;255;3;0;9;TSP:MSG:READ 50-50-0 s=255,c=4,t=2,pt=6,l=6,sg=0:640002000000 [2016-10-29 14:30:37.612 Info] TX 50;255;4;0;3;6400020000000C94F7030C94A3190C947C190C941F04 [2016-10-29 14:30:37.622 Info] RX 50;255;4;0;2;640002000000 [2016-10-29 14:30:37.641 Info] RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=255,c=4,t=3,pt=6,l=22,sg=0,ft=0,st=ok:6400020000000C94F7030C94A3190C947C190C941F04 [2016-10-29 14:30:40.031 Info] RX 0;255;3;0;9;TSP:MSG:READ 50-50-255 s=255,c=3,t=7,pt=0,l=0,sg=0: [2016-10-29 14:30:40.046 Info] RX 0;255;3;0;9;TSP:MSG:BC [2016-10-29 14:30:40.060 Info] RX 0;255;3;0;9;TSP:MSG:FPAR REQ (sender=50) [2016-10-29 14:30:40.069 Info] RX 0;255;3;0;9;TSP:CHKUPL:OK [2016-10-29 14:30:40.077 Info] RX 0;255;3;0;9;TSP:MSG:GWL OK [2016-10-29 14:30:40.576 Info] RX 0;255;3;0;9;!TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=fail:0 [2016-10-29 14:30:40.594 Info] RX 0;255;3;0;9;TSP:MSG:READ 50-50-255 s=255,c=3,t=7,pt=0,l=0,sg=0: [2016-10-29 14:30:40.606 Info] RX 0;255;3;0;9;TSP:MSG:BC [2016-10-29 14:30:40.615 Info] RX 0;255;3;0;9;TSP:MSG:FPAR REQ (sender=50) [2016-10-29 14:30:40.624 Info] RX 0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL) [2016-10-29 14:30:40.633 Info] RX 0;255;3;0;9;TSP:MSG:GWL OK [2016-10-29 14:30:40.643 Info] RX 0;255;3;0;9;TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=ok:0 [2016-10-29 14:30:40.653 Info] RX 0;255;3;0;9;TSP:MSG:READ 50-50-255 s=255,c=3,t=7,pt=0,l=0,sg=0: [2016-10-29 14:30:40.662 Info] RX 0;255;3;0;9;TSP:MSG:BC [2016-10-29 14:30:40.673 Info] RX 0;255;3;0;9;TSP:MSG:FPAR REQ (sender=50) [2016-10-29 14:30:40.682 Info] RX 0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL) [2016-10-29 14:30:40.692 Info] RX 0;255;3;0;9;TSP:MSG:GWL OK [2016-10-29 14:30:40.774 Info] RX 0;255;3;0;9;!TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=fail:0 [2016-10-29 14:30:40.784 Info] RX 0;255;3;0;9;TSP:MSG:READ 50-50-255 s=255,c=3,t=7,pt=0,l=0,sg=0: [2016-10-29 14:30:40.794 Info] RX 0;255;3;0;9;TSP:MSG:BC [2016-10-29 14:30:40.806 Info] RX 0;255;3;0;9;TSP:MSG:FPAR REQ (sender=50) [2016-10-29 14:30:40.815 Info] RX 0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL) [2016-10-29 14:30:40.825 Info] RX 0;255;3;0;9;TSP:MSG:GWL OK [2016-10-29 14:30:41.089 Info] RX 0;255;3;0;9;!TSP:MSG:SEND 0-0-50-50 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=fail:0 [2016-10-29 14:30:41.110 Info] RX 0;255;3;0;9;TSP:MSG:READ 50-50-255 s=255,c=3,t=7,pt=0,l=0,sg=0: [2016-10-29 14:30:41.120 Info] RX 0;255;3;0;9;TSP:MSG:BC [2016-10-29 14:30:41.129 Info] RX 0;255;3;0;9;TSP:MSG:FPAR REQ (sender=50) [2016-10-29 14:30:41.139 Info] RX 0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL) [2016-10-29 14:30:41.148 Info] RX 0;255;3;0;9;TSP:MSG:GWL OKAny Tips?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login