Nodemcu + RFM69. Level converter needed?

[emc2]

And you set up the pins radio type in your gateway sketch too right?

// Enables and select radio type (if attached)
#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY   RF69_868MHZ
#define MY_RF69_IRQ_PIN 4
#define MY_RF69_SPI_CS 15

[gmccarthy]

@emc2 Yes

[emc2]

I guess you would need to give the logs for the gateway too, to see if you have a radio fail somewhere.

[gmccarthy]

@emc2 This is all I see on the gateway:

0;255;3;0;9;Starting gateway (RRNGE-, 2.0.0)
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:RADIO:OK
0;255;3;0;9;TSM:GW MODE
0;255;3;0;9;TSM:READY
scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 6
cnt 
f r0, scandone

connected with homenet, channel 1
dhcp client start...
..............ip:192.168.1.100,mask:255.255.255.0,gw:192.168.1.1
.IP: 192.168.1.100
0;255;3;0;9;No registration required
0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
pm open,type:2 0
0;255;3;0;9;TSP:SANCHK:OK
0;255;3;0;9;TSP:SANCHK:OK

[emc2]

It seems good on the gateway to me, no radio error at least.
Past that no idea.

[gmccarthy]

@emc2 Thanks. Will keep digging but I"m almost out of idea as well. :(

[emc2]

@gmccarthy maybe an interesting read:
https://forum.mysensors.org/topic/4889/esp8266-rfm69-gateway/5

[korttoma]

On the arduino mini I think you should connect the DI00 (IRQ) to pin 2 like you see on this page

For some CPU types the IRQ pin is hard coded and can not be re-assigned.

[TON RIJNAARD]

@gmccarthy i have insert this line in the gateway then was it working for me

#define MY_RFM69_PA_LEVEL RF69_PA_LOW

[gmccarthy]

@emc2 Interesting read.

@korttoma I've connected up IRQ line. Still no luck,

@TON-RIJNAARD Have tried that now as well. No luck.

Tried going back to basics and now have 2 x Arduino pros with RFM69 - both loaded with pingpong script.

Don't know where I'm going wrong but I can't even start the script - entering 1 or T does nothing. (I"ve used the script before with the NRF radio and it works)

Have also tried the latest dev version.

Just keep getting this on both arduinos:

0 MCO:BGN:INIT NODE,CP=RRNNA--,VER=2.0.1-beta
4 TSM:INIT
1 MCO:BGN:INIT NODE,CP=RRNNA--,VER=2.0.1-beta
5 TSM:INIT
7 TSM:INIT:TSP OK
8 TSM:FPAR
138 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2145 !TSM:FPAR:NO REPLY
2147 TSM:FPAR
2277 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4284 !TSM:FPAR:NO REPLY
4286 TSM:FPAR
4416 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6423 !TSM:FPAR:NO REPLY
6425 TSM:FPAR
6555 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8562 !TSM:FPAR:FAIL
8563 TSM:FAIL:CNT=1
8565 TSM:FAIL:PDT