How to build a repeater

[ramoncarranza]

@scalz Thanks so much I was looking for something like this as well, thanks again

[stingone]

@ramoncarranza

So just using that example code is enough?

[ramoncarranza]

@stingone yep all you have to do is upload it to your radio set-up and that's it, but you do waste a board and a radio unit, but in MY case is well worth it.

[stingone]

@ramoncarranza

Ok so no need to change any code in my original sensor? and will it send multiple values from more sensors if picked-up?

[ramoncarranza]

no need to change anything on your original sensors and and yes it will relay signals from multiple sensors to your gateway/controller. Just our of curiosity, what controller are you using???

[stingone]

@ramoncarranza said:

no need to change anything on your original sensors and and yes it will relay signals from multiple sensors to your gateway/controller. Just our of curiosity, what controller are you using???

Using pimatic v9. on a raspberry pi 3. I already build a mysensors combined temp/ph sensor. But had to change the code in mysensors v2.0. I'm using lot of 433mhz over more then 25 devices.. but im now changing also towards mysensors :). so the mysensors is a little bit new to me.

[stingone]

@ramoncarranza said:

no need to change anything on your original sensors and and yes it will relay signals from multiple sensors to your gateway/controller. Just our of curiosity, what controller are you using???

Just build the repeater today..how can i see check if it is working properly??

Nevermind its working :):) just received the information on the repeater... great support thanks

[stingone]

Now testing for few day's and i see that one of my sensors stops working after few minutes.. the one that is most close to the gateway... after resetting it sends af few minutes and then stops working again...

[mfalkvidd]

@stingone what does the serial debug output say?

[stingone]

@mfalkvidd said:

@stingone what does the serial debug output say?

TSM:UPL
TSP:PING:SEND (dest=0)
!TSP:MSG:SEND 6-6-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=fail:1
TSP:CHKUPL:FAIL (hops=255)
!TSM:UPL:FAIL
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSP:SEND:TNR
TSP:MSG:READ 5-5-6 s=255,c=3,t=8,pt=1,l=1,sg=0:1
TSP:MSG:FPAR RES (ID=5, dist=1)
TSP:MSG:PAR OK (ID=5, dist=2)
!TSP:SEND:TNR
TSM:FPAR:OK
TSM:ID
TSM:CHKID:OK (ID=6)
TSM:UPL
TSP:PING:SEND (dest=0)
!TSP:MSG:SEND 6-6-5-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=fail:1
TSP:CHKUPL:FAIL (hops=255)
!TSM:UPL:FAIL
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
Init complete, id=6, parent=255, distance=255, registration=1
!TSP:SEND:TNR```

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=6)
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=6)
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=6)
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 6-6-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT