MYSBootloader 1.3.0-beta.3

Feji

It's a 56K version, I haven't try 38k yet.

MiKa

@Feji
try 38400Bd it should work

HW.h

#ifndef BAUD_RATE
#if F_CPU >= 16000000L
#define BAUD_RATE 115200
#elif F_CPU >= 8000000L
#define BAUD_RATE 38400L
#elif F_CPU >= 1000000L
#define BAUD_RATE 9600L
#elif F_CPU >= 128000L
#define BAUD_RATE 4800L
#else
#define BAUD_RATE 1200L
#endif

Feji

@MiKa

My bad, it's a 38k version but I was trying to upload the sketch at 56k...

Feji

@Feji

After modifying the HW.h, it's work much better :). Obviously...
Serial upload confirmed work at 57600.

Werwolfx

Hello everybody.

I have a problem with the update over the air.
Version 2.1.0 mysensors
Gateway on ESP8266 default sketh
I downloaded the loader in atmega328p Arduino pro mini

in MYSController choose firmware
in logs


[12.01.2017 20: 32: 50.118 Info] INFO BL version = 768
 [12.01.2017 20: 32: 50.118 Info] INFO Send FW info to node 4: type = A, version = 1, blocks = 0x0050, CRC = 0x46D4
 [12/01/2017 20: 32: 50.120 Info] TX 4, 0, 4, 0, 1; 0A0001005000D446
 [12/01/2017 20: 32: 52.205 Info] RX 0, 255, 3, 0, 2, 2.1.0
 [12.01.2017 20: 32: 53.724 Info] RX 10, 3, 1, 0, 0, 21.2
 [12/01/2017 20: 32: 53.736 Info] RX 4; 255; 3, 0, 6, 0
 [12/01/2017 20: 32: 53.737 Info] TX 4; 255; 3, 0; 6; M

in arduino serial

0 MCO: BGN: INIT NODE, CP = RNONA -, VER = 2.1.0
3 TSM: INIT
4 TSF: WUR: MS = 0
11 TSM: INIT: TSP OK
13 TSM: INIT: STATID = 4
15 TSF: SID: OK, ID = 4
16 TSM: FPAR
53 TSF: MSG: SEND, 4-4-255-255, s = 255, c = 3, t = 7, pt = 0, l = 0, sg = 0, ft = 0, st = OK:
592 TSF: MSG: READ, 0-0-4, s = 255, c = 3, t = 8, pt = 1, l = 1, sg = 0: 0
598 TSF: MSG: FPAR OK, ID = 0, D = 1
2060 TSM: FPAR: OK
2061 TSM: ID
2062 TSM: ID: OK
2064 TSM: UPL
2069 TSF: MSG: SEND, 4-4-0-0, s = 255, c = 3, t = 24, pt = 1, l = 1, sg = 0, ft = 0, st = OK: 1
2083 TSF: MSG: READ, 0-0-4, s = 255, c = 3, t = 25, pt = 1, l = 1, sg = 0: 1
2088 TSF: MSG: PONG RECV, HP = 1
2092 TSM: UPL: OK
2093 TSM: READY: ID = 4, PAR = 0, DIS = 1
2113 TSF: MSG: SEND, 4-4-0-0, s = 255, c = 4, t = 0, pt = 6, l = 10, sg = 0, ft = 0, st = OK: FFFFFFFFD0033C3E0300
2131 TSF: MSG: SEND, 4-4-0-0, s = 255, c = 3, t = 15, pt = 6, l = 2, sg = 0, ft = 0, st = OK: 0100
2138 TSF: MSG: READ, 0-0-4, s = 0, c = 4, t = 1, pt = 6, l = 8, sg = 0: 0A0001005000D446
2144 OTA: FWP: UPDATE
! 2146 OTA: FWP: FLASH INIT FAIL
2151 TSF: MSG: READ, 0-0-4, s = 255, c = 3, t = 15, pt = 6, l = 2, sg = 0: 0100
4074 TSF:! MSG: SEND, 4-4-0-0, s = 255, c = 0, t = 17, pt = 0, l = 5, sg = 0, ft = 0, st = NACK: 2.1. 0
5727 TSF: MSG: SEND, 4-4-0-0, s = 255, c = 3, t = 6, pt = 1, l = 1, sg = 0, ft = 1, st = OK: 0
5734 TSF: MSG: READ, 10-10-0, s = 3, c = 1, t = 0, pt = 7, l = 5, sg = 0: 21.2
! 5739 TSF: MSG: REL MSG, NREP
5817 TSF: MSG: READ, 0-0-4, s = 255, c = 3, t = 6, pt = 0, l = 1, sg = 0: M
! 7739 TSF: MSG: SEND, 4-4-0-0, s = 1, c = 0, t = 23, pt = 0, l = 0, sg = 0, ft = 0, st = NACK:
8436 TSF: MSG: SEND, 4-4-0-0, s = 255, c = 3, t = 11, pt = 0, l = 9, sg = 0, ft = 1, st = OK: Yang Node
8462 TSF: MSG: SEND, 4-4-0-0, s = 255, c = 3, t = 12, pt = 0, l = 4, sg = 0, ft = 0, st = OK: v1.0

confuse line
2144 OTA: FWP: UPDATE
! 2146 OTA: FWP: FLASH INIT FAIL

what could be the problem?

tekka

@Werwolfx
Disable MY_OTA_FIRMWARE_FEATURE, this is only required for the external flash/dualoptiboot OTA method, MYSBootloader handles OTA updates offline.

Werwolfx

@tekka oh, my mistake, thank you very much for your work.

Werwolfx

I try to disable MY_OTA_FIRMWARE_FEATURE in arduino/
but no effect =(
In arduino load example code PingpongSensor and add in sketch
#define MY_NODE_ID 4

MYSController log

14.01.2017 8:43:45	CLICK	Board with MYSBootloader=TRUE
14.01.2017 8:43:46	RX	10;5;1;0;17;841
14.01.2017 8:43:46	RX	10;6;1;0;39;3.66
14.01.2017 8:43:52	RX	0;255;3;0;2;2.1.0
14.01.2017 8:43:54	TX	4;0;3;0;13;0
14.01.2017 8:43:54	INFO	FW "TimeReporter" assigned to node 4
14.01.2017 8:43:57	RX	6;3;1;0;16;0
14.01.2017 8:43:57	RX	6;6;1;0;3;0
14.01.2017 8:43:57	RX	5;3;1;0;16;0
14.01.2017 8:43:57	RX	5;6;1;0;3;0
14.01.2017 8:43:57	RX	6;5;1;0;0;20.25
14.01.2017 8:44:00	RX	4;255;0;0;17;2.1.0
14.01.2017 8:44:00	CHILD	New child discovered, node id=4, child id=internal
14.01.2017 8:44:00	DEBUG	Update child id=255, type=S_ARDUINO_NODE
14.01.2017 8:44:00	RX	4;255;3;0;6;0
14.01.2017 8:44:00	TX	4;255;3;0;6;M
14.01.2017 8:44:00	RX	4;1;0;0;23;
14.01.2017 8:44:00	CHILD	New child discovered, node id=4, child id=1
14.01.2017 8:44:00	DEBUG	Update child id=1, type=S_CUSTOM
14.01.2017 8:44:00	RX	4;255;3;0;12;v1.0

Arduino serial

38602 TSF:MSG:READ,0-0-4,s=0,c=3,t=13,pt=0,l=1,sg=0:0 
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.0
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
12 TSM:INIT:STATID=4
14 TSF:SID:OK,ID=4
16 TSM:FPAR
52 TSF:MSG:SEND,4-4-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
153 TSF:MSG:READ,0-0-4,s=255,c=3,t=8,pt=1,l=1,sg=0:0
157 TSF:MSG:FPAR OK,ID=0,D=1
2060 TSM:FPAR:OK
2061 TSM:ID
2062 TSM:ID:OK
2064 TSM:UPL
2067 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2081 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2086 TSF:MSG:PONG RECV,HP=1
2088 TSM:UPL:OK
2091 TSM:READY:ID=4,PAR=0,DIS=1
2122 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2128 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2139 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.0
2151 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2170 TSF:MSG:READ,0-0-4,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2184 TSF:MSG:SEND,4-4-0-0,s=1,c=0,t=23,pt=0,l=0,sg=0,ft=0,st=OK:
2192 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=9,sg=0,ft=0,st=OK:Yang Node
2236 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=4,sg=0,ft=0,st=NACK:v1.0

Yang NodeReady.
2243 MCO:REG:REQ
2249 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=OK:2
2265 TSF:MSG:READ,0-0-4,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2269 MCO:PIM:NODE REG=1
2272 MCO:BGN:STP
2273 MCO:BGN:INIT OK,TSP=1
2315 TSF:MSG:READ,0-0-4,s=255,c=3,t=6,pt=0,l=6,sg=0:Metric

0_1484381990012_upload-678581ea-b243-4cea-8b4b-12fd2faf9c9b

tekka

@Werwolfx I don't see any MYSBootloader startup message in your log. Please re-download the .hex from the github repo to ensure you are on the most recent version and flash it following these instructions: https://www.mysensors.org/about/ota

Werwolfx

@tekka
i tryed it
My little instructions for Arduino Atmega328p 5v ext
1)download from https://github.com/mysensors/MySensorsBootloaderRF24
2)copy to arduino folder arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors and paste boards.txt

proMYSBL.name=ATmega328 16Mhz MYSBootloader

proMYSBL.upload.tool=avrdude
proMYSBL.upload.protocol=arduino
proMYSBL.upload.maximum_size=30720
proMYSBL.upload.maximum_data_size=2048
proMYSBL.upload.speed=115200

proMYSBL.bootloader.tool=avrdude
proMYSBL.bootloader.low_fuses=0xF7
proMYSBL.bootloader.high_fuses=0xDA
proMYSBL.bootloader.extended_fuses=0x06
proMYSBL.bootloader.unlock_bits=0x3F
proMYSBL.bootloader.lock_bits=0x0F
proMYSBL.bootloader.file=MySensors/MYSBootloader.hex

proMYSBL.build.mcu=atmega328p
proMYSBL.build.f_cpu=16000000L
proMYSBL.build.board=AVR_UNO
proMYSBL.build.core=arduino
proMYSBL.build.variant=standard

3)In Arduino IDE select downloadex bootloader and burn it to Atmega
avrdude log

/home/werwolfx/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino8/bin/avrdude -C/home/werwolfx/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino8/etc/avrdude.conf -v -patmega328p -cusbasp -Pusb -e -Ulock:w:0x3F:m -Uefuse:w:0x06:m -Uhfuse:w:0xDA:m -Ulfuse:w:0xF7:m 

avrdude: Version 6.3, compiled on Dec 16 2016 at 12:32:01
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/home/werwolfx/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino8/etc/avrdude.conf"
         User configuration file is "/home/werwolfx/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : usb
         Using Programmer              : usbasp
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : usbasp
         Description     : USBasp, http://www.fischl.de/usbasp/

avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: erasing chip
avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: reading input file "0x3F"
avrdude: writing lock (1 bytes):

/home/werwolfx/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino8/bin/avrdude -C/home/werwolfx/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino8/etc/avrdude.conf -v -patmega328p -cusbasp -Pusb -Uflash:w:/media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex:i -Ulock:w:0x0F:m 
Writing | ################################################## | 100% 0.00s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x3F:
avrdude: load data lock data from input file 0x3F:
avrdude: input file 0x3F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 1 bytes of lock verified
avrdude: reading input file "0x06"
avrdude: writing efuse (1 bytes):

Writing |  ***failed;  
################################################## | 100% 0.03s

avrdude: 1 bytes of efuse written
avrdude: verifying efuse memory against 0x06:
avrdude: load data efuse data from input file 0x06:
avrdude: input file 0x06 contains 1 bytes
avrdude: reading on-chip efuse data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: WARNING: invalid value for unused bits in fuse "efuse", should be set to 1 according to datasheet
This behaviour is deprecated and will result in an error in future version
You probably want to use 0xfe instead of 0x06 (double check with your datasheet first).
avrdude: 1 bytes of efuse verified
avrdude: reading input file "0xDA"
avrdude: writing hfuse (1 bytes):

Writing | ################################################## | 100% 0.00s

avrdude: 1 bytes of hfuse written
avrdude: verifying hfuse memory against 0xDA:
avrdude: load data hfuse data from input file 0xDA:
avrdude: input file 0xDA contains 1 bytes
avrdude: reading on-chip hfuse data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 1 bytes of hfuse verified
avrdude: reading input file "0xF7"
avrdude: writing lfuse (1 bytes):

Writing | ################################################## | 100% 0.01s

avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xF7:
avrdude: load data lfuse data from input file 0xF7:
avrdude: input file 0xF7 contains 1 bytes
avrdude: reading on-chip lfuse data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...

avrdude: 1 bytes of lfuse verified
avrdude: Version 6.3, compiled on Dec 16 2016 at 12:32:01

         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/home/werwolfx/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino8/etc/avrdude.conf"
         User configuration file is "/home/werwolfx/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : usb
         Using Programmer              : usbasp
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
avrdude done.  Thank you.
         PAGEL                         : PD7

         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : usbasp
         Description     : USBasp, http://www.fischl.de/usbasp/

avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: reading input file "/media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex"
avrdude: writing flash (32762 bytes):

Writing | ################################################## | 100% 0.00s

avrdude: 32762 bytes of flash written
avrdude: verifying flash memory against /media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex:
avrdude: load data flash data from input file /media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex:
avrdude: input file /media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex contains 32762 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 32762 bytes of flash verified
avrdude: reading input file "0x0F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.01s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x0F:
avrdude: load data lock data from input file 0x0F:
avrdude: input file 0x0F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 1 bytes of lock verified

avrdude done.  Thank you.

I loaded test sketh WaterMeterPulssensor (from Mysensors example) to arduino
wait if the module is start and see to MYSController
in MYSController

14.01.2017 11:34:49	RX	5;6;1;0;3;0
14.01.2017 11:34:52	RX	10;5;1;0;17;5519
14.01.2017 11:34:52	RX	10;6;1;0;39;23.99
14.01.2017 11:34:57	RX	6;3;1;0;16;0
14.01.2017 11:34:58	RX	6;4;1;0;37;170
14.01.2017 11:34:58	RX	6;6;1;0;3;0
14.01.2017 11:34:58	RX	6;5;1;0;0;20.50
14.01.2017 11:35:01	RX	4;255;0;0;17;2.1.0
14.01.2017 11:35:01	DEBUG	Update child id=255, type=S_ARDUINO_NODE
14.01.2017 11:35:01	RX	4;255;3;0;6;0
14.01.2017 11:35:01	TX	4;255;3;0;6;M
14.01.2017 11:35:02	RX	4;255;3;0;11;Water Meter
14.01.2017 11:35:02	RX	4;255;3;0;12;1.1
14.01.2017 11:35:02	RX	4;1;0;0;21;
14.01.2017 11:35:02	DEBUG	Update child id=1, type=S_WATER
14.01.2017 11:35:02	RX	4;1;2;0;24;
14.01.2017 11:35:08	RX	10;5;1;0;17;5462
14.01.2017 11:35:08	RX	10;6;1;0;39;23.75
14.01.2017 11:35:18	RX	7;3;1;0;16;0
14.01.2017 11:35:18	RX	7;4;1;0;37;192
14.01.2017 11:35:18	RX	7;6;1;0;3;0
14.01.2017 11:35:19	RX	5;3;1;0;16;0
14.01.2017 11:35:19	RX	5;4;1;0;37;34
14.01.2017 11:35:19	RX	5;6;1;0;3;0

5)in MYSController Assign FW Blink and Reboot
MYSController

14.01.2017 11:38:03	TX	4;0;3;0;13;0
14.01.2017 11:38:09	RX	4;255;0;0;17;2.1.0
14.01.2017 11:38:09	CHILD	New child discovered, node id=4, child id=internal
14.01.2017 11:38:09	DEBUG	Update child id=255, type=S_ARDUINO_NODE
14.01.2017 11:38:09	RX	4;255;3;0;6;0
14.01.2017 11:38:09	TX	4;255;3;0;6;M
14.01.2017 11:38:09	RX	4;255;3;0;11;Water Meter
14.01.2017 11:38:09	RX	4;255;3;0;12;1.1
14.01.2017 11:38:09	RX	4;1;0;0;21;
14.01.2017 11:38:09	CHILD	New child discovered, node id=4, child id=1
14.01.2017 11:38:09	DEBUG	Update child id=1, type=S_WATER
14.01.2017 11:38:10	RX	4;1;2;0;24;
14.01.2017 11:38:14	RX	4;255;3;0;21;0

Serial

101794 TSF:MSG:READ,0-0-4,s=0,c=3,t=13,pt=0,l=1,sg=0:0
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.0
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:INIT:STATID=4
14 TSF:SID:OK,ID=4
16 TSM:FPAR
52 TSF:MSG:SEND,4-4-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
345 TSF:MSG:READ,0-0-4,s=255,c=3,t=8,pt=1,l=1,sg=0:0
350 TSF:MSG:FPAR OK,ID=0,D=1
2060 TSM:FPAR:OK
2061 TSM:ID
2062 TSM:ID:OK
2064 TSM:UPL
2067 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2081 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2086 TSF:MSG:PONG RECV,HP=1
2089 TSM:UPL:OK
2091 TSM:READY:ID=4,PAR=0,DIS=1
2098 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2104 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2114 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.0
2126 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2157 TSF:MSG:READ,0-0-4,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2164 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=11,sg=0,ft=0,st=OK:Water Meter
2176 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.1
2183 TSF:MSG:SEND,4-4-0-0,s=1,c=0,t=21,pt=0,l=0,sg=0,ft=0,st=OK:
2189 MCO:REG:REQ
2193 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2245 TSF:MSG:READ,0-0-4,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2250 MCO:PIM:NODE REG=1
2252 MCO:BGN:STP
2255 TSF:MSG:SEND,4-4-0-0,s=1,c=2,t=24,pt=0,l=0,sg=0,ft=0,st=OK:
2262 MCO:BGN:INIT OK,TSP=1
2335 TSF:MSG:READ,0-0-4,s=255,c=3,t=6,pt=0,l=6,sg=0:Metric
2866 TSF:MSG:READ,0-0-4,s=1,c=1,t=24,pt=0,l=6,sg=0:400100
Received last pulse count from gw:400100
6381 TSF:MSG:READ,0-0-255,s=255,c=3,t=20,pt=0,l=0,sg=0:
6386 TSF:MSG:BC
6637 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=21,pt=1,l=1,sg=0,ft=0,st=OK:0```

tekka

@Werwolfx but still no signs of MYSBootloader - what RF channel are you on?

Werwolfx

@tekka
NRF24L01+
#define MY_RADIO_NRF24

What is the "no signs of MYSBootloader"?

tekka

@Werwolfx As soon as the bootloader takes over, in your case after the reboot request (1), but before the MYS lib 2.1.0 init message (2):

(1) 14.01.2017 11:38:03 TX  4;0;3;0;13;0
(2) 14.01.2017 11:38:09 RX  4;255;0;0;17;2.1.0

it will send a I_FIRMWARE_CONFIG_REQUEST message to inform the controller about the currently loaded FW and request a new FW.

looks like this:

4;255;4;0;0;BE0001003003D8490102

This is missing in your case, therefore I'm wondering if you have incompatible radio settings. Please post your GW sketch and upload your MYSBootloader.hex file for further troubleshooting.

Werwolfx

@tekka GW on esp8266 (default sketch) + NRF24L01+
on GW

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik EKblad
 * Contribution by a-lurker and Anticimex,
 * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
 * Contribution by Ivo Pullens (ESP8266 support)
 *
 * DESCRIPTION
 * The EthernetGateway sends data received from sensors to the WiFi link.
 * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
 *
 * VERA CONFIGURATION:
 * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin.
 * E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003
 *
 * LED purposes:
 * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch, only the LEDs that is defined is used.
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
 * nRF24L01+  ESP8266
 * VCC        VCC
 * CE         GPIO4
 * CSN/CS     GPIO15
 * SCK        GPIO14
 * MISO       GPIO12
 * MOSI       GPIO13
 * GND        GND
 *
 * Not all ESP8266 modules have all pins available on their external interface.
 * This code has been tested on an ESP-12 module.
 * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
 * - Connect REST (reset) via 10K pullup resistor to VCC, and via switch to GND ('reset switch')
 * - Connect GPIO15 via 10K pulldown resistor to GND
 * - Connect CH_PD via 10K resistor to VCC
 * - Connect GPIO2 via 10K resistor to VCC
 * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
 *
  * Inclusion mode button:
 * - Connect GPIO5 via switch to GND ('inclusion switch')
 *
 * Hardware SHA204 signing is currently not supported!
 *
 * Make sure to fill in your ssid and WiFi password below for ssid & pass.
 */


// Enable debug prints to serial monitor
#define MY_DEBUG

// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 115200

// Enables and select radio type (if attached)
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_GATEWAY_ESP8266

#define MY_ESP8266_SSID "WiFI"
#define MY_ESP8266_PASSWORD "password[0_1484386469111_MYSBootloader.hex](/uploads/files/1484386469171-mysbootloader.hex) "

// Enable UDP communication
//#define MY_USE_UDP

// Set the hostname for the WiFi Client. This is the hostname
// it will pass to the DHCP server if not static.
// #define MY_ESP8266_HOSTNAME "sensor-gateway"

// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
//#define MY_IP_ADDRESS 192,168,178,87

// If using static ip you need to define Gateway and Subnet address as well
//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
//#define MY_IP_SUBNET_ADDRESS 255,255,255,0

// The port to keep open on node server mode
#define MY_PORT 5003

// How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE

// Enable Inclusion mode button on gateway
// #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3


// Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
// Led pins used if blinking feature is enabled above
#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED

#if defined(MY_USE_UDP)
  #include <WiFiUdp.h>
#endif

#include <ESP8266WiFi.h>

#include <MySensors.h>

void setup() {
}

void presentation() {
  // Present locally attached sensors here
}


void loop() {
  // Send locally attached sensors data here
}

In MYSController on mudule i click INFO
FW Update = no
Bootloader = N/A

may be problem in the Bootloader.hex?

0_1484386859986_upload-c59e469e-e015-4099-88d8-607a7408a1da

tekka

@Werwolfx Please also update the bootloader file.

Werwolfx

@tekka said:

@Werwolfx Please also update the bootloader file.

I'll update more than once, but there is no effect.
avrdude writes that everything is OK
I do not know what to do = (

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: reading input file "/media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex"
avrdude: writing flash (32762 bytes):

Writing | ################################################## | 100% 0.00s

avrdude: 32762 bytes of flash written
avrdude: verifying flash memory against /media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex:
avrdude: load data flash data from input file /media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex:
avrdude: input file /media/werwolfx/SSDData/arduino-1.8.0/hardware/arduino/avr/bootloaders/MySensors/MYSBootloader.hex contains 32762 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 32762 bytes of flash verified
avrdude: reading input file "0x0F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.01s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x0F:
avrdude: load data lock data from input file 0x0F:
avrdude: input file 0x0F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 1 bytes of lock verified

avrdude done.  Thank you.

tekka

@Werwolfx sorry, maybe I was not clear - please upload it here to the forum I will try to reproduce your setup.

Werwolfx

@tekka If i ENABLE #define MY_OTA_FIRMWARE_FEATURE
i see ST_FIRMWARE_CONFIG_REQUEST in MYSCONTROLLER logs!!!
if i DISABLE //#define MY_OTA_FIRMWARE_FEATURE msg not in log

i not have external flash/

402	14.01.2017 21:29:28	TX	4 - Water Meter	N/A	C_INTERNAL	NO	I_REBOOT	0
403	14.01.2017 21:29:28	RX	4	1	C_REQ	NO	V_VAR1	
408	14.01.2017 21:29:34	RX	4	INTERNAL	C_STREAM	NO	ST_FIRMWARE_CONFIG_REQUEST	FFFFFFFF48044E100300
409	14.01.2017 21:29:34	TX	4	N/A	C_STREAM	NO	ST_FIRMWARE_CONFIG_RESPONSE	0A0001005000D446
410	14.01.2017 21:29:34	RX	4	INTERNAL	C_PRESENTATION	NO	S_ARDUINO_NODE	2.1.0
411	14.01.2017 21:29:34	RX	4	INTERNAL	C_INTERNAL	NO	I_CONFIG	0
412	14.01.2017 21:29:34	TX	4	INTERNAL	C_INTERNAL	NO	I_CONFIG	M
414	14.01.2017 21:29:34	RX	4 - Water Meter	INTERNAL	C_INTERNAL	NO	I_SKETCH_NAME	Water Meter
417	14.01.2017 21:29:34	RX	4 - Water Meter	INTERNAL	C_INTERNAL	NO	I_SKETCH_VERSION	1.1
419	14.01.2017 21:29:34	RX	4 - Water Meter	1 - S_WATER	C_PRESENTATION	NO	S_WATER

i load this HEX
load from Arduino IDE 1.8.0
0_1484418874223_MYSBootloader.hex

board.txt

proMYSBL.bootloader.tool=avrdude
proMYSBL.bootloader.low_fuses=0xFF
proMYSBL.bootloader.high_fuses=0xDA
proMYSBL.bootloader.extended_fuses=0xFE
proMYSBL.bootloader.unlock_bits=0x3F
proMYSBL.bootloader.lock_bits=0x0F
proMYSBL.bootloader.file=MySensors/MYSBootloader.hex

tekka

@Werwolfx Ok, seems like you also upload the sketch via USBasp thereby erasing/overwriting the bootloader. Try uploading the sketch via serial or OTA after flashing the bootloader.

Mark Swift

@tekka am I correct in thinking the HEX found on Github can be used with all Arduino's? I noticed my old folder has one hex for 16, 8 and 1Mhz?

I'm using this board.txt

menu.cpu=Processor

##############################################################

MYSBL13.name=MYS Bootloader - atmega328p

MYSBL13.upload.tool=arduino:avrdude
MYSBL13.upload.protocol=arduino
MYSBL13.upload.maximum_size=30720
MYSBL13.upload.maximum_data_size=2048

MYSBL13.bootloader.tool=arduino:avrdude
MYSBL13.bootloader.unlock_bits=0x3F
MYSBL13.bootloader.lock_bits=0x0F

MYSBL13.build.mcu=atmega328p
MYSBL13.build.board=AVR_PRO
MYSBL13.build.core=arduino:arduino
MYSBL13.build.variant=arduino:standard

## -------------------------------------------------

MYSBL13.menu.cpu.16MHzatmega328=ATmega328 16MHz (XTAL, BOD1V8)
MYSBL13.menu.cpu.16MHzatmega328.upload.speed=115200
MYSBL13.menu.cpu.16MHzatmega328.bootloader.low_fuses=0xFF
MYSBL13.menu.cpu.16MHzatmega328.bootloader.high_fuses=0xDA
MYSBL13.menu.cpu.16MHzatmega328.bootloader.extended_fuses=0x06
MYSBL13.menu.cpu.16MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader.hex
MYSBL13.menu.cpu.16MHzatmega328.build.f_cpu=16000000L

MYSBL13.menu.cpu.8MHzatmega328=ATmega328 8MHz (RC, BOD1V8)
MYSBL13.menu.cpu.8MHzatmega328.upload.speed=38400
MYSBL13.menu.cpu.8MHzatmega328.bootloader.low_fuses=0xE2
MYSBL13.menu.cpu.8MHzatmega328.bootloader.high_fuses=0xDA
MYSBL13.menu.cpu.8MHzatmega328.bootloader.extended_fuses=0x06
MYSBL13.menu.cpu.8MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader.hex
MYSBL13.menu.cpu.8MHzatmega328.build.f_cpu=8000000L

MYSBL13.menu.cpu.1MHzatmega328=ATmega328 1MHz (RC/8, BOD1V8)
MYSBL13.menu.cpu.1MHzatmega328.upload.speed=9600
MYSBL13.menu.cpu.1MHzatmega328.bootloader.low_fuses=0x62
MYSBL13.menu.cpu.1MHzatmega328.bootloader.high_fuses=0xDA
MYSBL13.menu.cpu.1MHzatmega328.bootloader.extended_fuses=0x06
MYSBL13.menu.cpu.1MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader.hex
MYSBL13.menu.cpu.1MHzatmega328.build.f_cpu=1000000L```

MYSBootloader 1.3.0-beta.3

14

11.7k

11.2k

113.0k