Mysensors Gateway on OrangePi (Zero) (opi)

Tag

Just hooked up a radio to the GPIO header. (used this link for the model 1 RPI https://www.mysensors.org/build/raspberry and attached the interrupt pin also to pin 15)

This is the result i get
root@orangepizero:~/marceloaqno-spidev/bin# mysgw
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: Could not open /sys/class/gpio/gpio10/direction
Illegal instruction
root@orangepizero:~/marceloaqno-spidev/bin#

marceloaqno

@Tag Great! The mapping of the physical GPIO number in OrangePi is not ready yet, so you need to figure out the correct value for the CE and CSN pins by adding this to the examples_linux/mysgw.cpp or MyConfig.h

#define MY_RF24_CE_PIN X
#define MY_RF24_CS_PIN Y

This is the best pinout image I've found that could help:
https://oshlab.com/orange-pi-zero-pinout/

This may also give you some hint:

cat /sys/kernel/debug/gpio

marceloaqno

@Tag Maybe this one can help too:
http://orange314.com/WiringOP

marceloaqno

@Tag also, please don't set the interrupt pin for now.

marceloaqno

@Tag I found more information on the wiki page about the gpio pins:
http://linux-sunxi.org/GPIO

It seems that there is a calculation to be made to know which number to use :scream:

Tag

@marceloaqno

Hi!!, many thanks for the info!! really helpful!
Made some progress. first I created this table based on this page: http://linux-sunxi.org/GPIO

Pin - Num - Name - Calculated value A=1 ((1-1)*32 + Pin)
CE / 22 / PA02 / 2
SCK / 23 / PA14 / 14
MISO / 21 / PA16 / 16
CSN / 24 / PA13 / 13
MOSI / 19 / PA15 / 15

Now it is important that you know which kernel is used on your systems the 4.x architecture is different compared to the 3.x arch...

If the 4.x kernel is used you need to use the calculated value for the GPIO pin numbering, i could not test that since I am using the 3.x kernel, so this is what i did:

load the GPIO kernel module:

modprobe gpio-sunxi

Create the GPIO device files since these were not available on my system by default.

for A in 1 2 3 4 5 6 7 8 9 10 11 12; do echo "$A" > /sys/class/gpio/export ; done

This created the following entries in /sys/class/gpio

root@orangepizero:~/marceloaqno-spidev/bin# ls -l /sys/class/gpio
total 0
--w------- 1 root root 4096 Jan  8 07:39 export
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio1 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio1
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio11 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio11
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio12 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio12
lrwxrwxrwx 1 root root    0 Jan  8 07:32 gpio13 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio13
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio2 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio2
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio3 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio3
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio4 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio4
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio5 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio5
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio6 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio6
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio7 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio7
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio8 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio8
lrwxrwxrwx 1 root root    0 Jan  8 07:16 gpio9 -> ../../devices/platform/sunxi-pinctrl/gpio/gpio9
lrwxrwxrwx 1 root root    0 Jan  1  1970 gpiochip0 -> ../../devices/platform/sunxi-pinctrl/gpio/gpiochip0
--w------- 1 root root 4096 Jan  1  1970 unexport

Modified mysgw.cpp to use:

#define MY_RF24_CE_PIN 2
#define MY_RF24_CS_PIN 13

And did a clean build:

make clean
./configure
make

Now some thing has changed! :)

root@orangepizero:~/marceloaqno-spidev/bin# ./mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-beta
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT

Will do some more testing with an LED today see if the GPIO pin numbering that was created is okay,

will keep you posted!:

Tag

@marceloaqno
Did some testing,

Setup the GPIO pins:

modprobe gpio-sunxi

for A in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 
do echo "$A" > /sys/class/gpio/export
done

(The device files that are created by the commands above do not survive a reboot, so remember to execute the above commands after each reboot!)

Hooked up an led between ground and i.e. pin 22, this pin is linked to GPIO2

Then:

echo out > /sys/class/gpio/gpio2/direction
echo 1 > /sys/class/gpio/gpio2/value
echo 0 > /sys/class/gpio/gpio2/value

And eureka!! Led went on and off :D

Did this for all GPIO ports used by mysgw, below is the verified pin / GPIO table

Pin#  -  GPIO / NRF24 
22 - GPIO2   / CE
23 - GPIO14  / SCK
21 - GPIO16  / MISO
24 - GPIO13  / CSN
19 - GPIO15  / MOSI

Tested all pins and led went on and off on all

How i connected the radio: https://www.mysensors.org/build/raspberry (see the Pi1 part)
How to setup GPIO: http://linux-sunxi.org/GPIO (3.x kernel part, and added pin 13/14/15/16)
Pinout for the OPI Zero: https://i1.wp.com/oshlab.com/wp-content/uploads/2016/11/Orange-Pi-Zero-Pinout-banner2.jpg?fit=1200%2C628&ssl=1 (carefully look at the pin numbering!)

Maybe it is usefull, I rebuild mysgw with NRF24 radio debugging enabled, this is the output I get:

root@orangepizero:~/marceloaqno-spidev/bin# ./mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-beta
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: RF24:write register, reg=0, value=14
mysgw: RF24:write register, reg=3, value=3
mysgw: RF24:write register, reg=4, value=95
mysgw: RF24:write register, reg=5, value=76
mysgw: RF24:write register, reg=6, value=39
mysgw: RF24:write register, reg=16, value=115
mysgw: RF24:write register, reg=29, value=6
mysgw: RF24:read register, reg=6, value=0
mysgw: RF24:read register, reg=5, value=0
mysgw: !RF24:INIT:SANCHK FAIL
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: RF24:write register, reg=0, value=12
mysgw: RF24:PD
^Cmysgw: Received SIGINT

keeps looping, until ctrl-c is given.

mihai.aldea

@Tag said:

Made some progress. first I created this table based on this page: http://linux-sunxi.org/GPIO

Pin - Num - Name - Calculated value
CE / 22 / PA02 / 482
SCK / 23 / PA14 / 494
MISO / 21 / PA16 / 496
CSN / 24 / PA13 / 493
MOSI / 19 / PA15 / 495

Are you sure this is correct?
The formula is: (position of letter in alphabet - 1) * 32 + pin number
For PA02 for instance the correct value is:
PA02 = (1 - 1) * 32 + 02 = 2

Actually you don't need to use the formula at all with the PA ports, all you have to do is use the trailing number.

Tag

@mihai.aldea

You are right, took the letter P, which is 16.... but is should have been A.... (for the 4.x kernel)
Updated the table!,

Thx!!

Reza

i have problem in build gateway on orangepi one

root@OrangePI:~/marceloaqno-spidev# make
Makefile:16: Makefile.inc: No such file or directory
[Running configure]
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=H3, Type=unknown, CPU=armv7l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:SPIDEV.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[OK] Finished.
gcc -MT build/drivers/Linux/log.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/log.c -o build/drivers/Linux/log.o
g++ -MT build/drivers/Linux/IPAddress.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/IPAddress.cpp -o build/drivers/Linux/IPAddress.o
g++ -MT build/drivers/Linux/noniso.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/noniso.cpp -o build/drivers/Linux/noniso.o
g++ -MT build/drivers/Linux/GPIO.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/GPIO.cpp -o build/drivers/Linux/GPIO.o
g++ -MT build/drivers/Linux/Print.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Print.cpp -o build/drivers/Linux/Print.o
g++ -MT build/drivers/Linux/EthernetClient.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetClient.cpp -o build/drivers/Linux/EthernetClient.o
g++ -MT build/drivers/Linux/SerialPort.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SerialPort.cpp -o build/drivers/Linux/SerialPort.o
g++ -MT build/drivers/Linux/Stream.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Stream.cpp -o build/drivers/Linux/Stream.o
g++ -MT build/drivers/Linux/compatibility.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/compatibility.cpp -o build/drivers/Linux/compatibility.o
g++ -MT build/drivers/Linux/interrupt.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/interrupt.cpp -o build/drivers/Linux/interrupt.o
drivers/Linux/interrupt.cpp: In function ‘void* interruptHandler(void*)’:
drivers/Linux/interrupt.cpp:107:26: warning: ignoring return value of ‘ssize_t read(int, void*, size_t)’, declared with attribute warn_unused_result [-Wunused-result]
   (void)read (fd, &c, 1) ;
                          ^
g++ -MT build/drivers/Linux/SoftEeprom.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SoftEeprom.cpp -o build/drivers/Linux/SoftEeprom.o
g++ -MT build/drivers/Linux/EthernetServer.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetServer.cpp -o build/drivers/Linux/EthernetServer.o
g++ -MT build/examples_linux/mysgw.o -MMD -MP -march=armv8-a -mtune=cortex-a53 -mfpu=neon-vfpv4 -mfloat-abi=hard -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o
In file included from ./MySensors.h:294:0,
                 from examples_linux/mysgw.cpp:74:
./drivers/RF24/RF24.cpp:39:11: error: Not supported on this platform.
  hwDigitalWrite(MY_RF24_CS_PIN, level);
           ^
./drivers/RF24/RF24.cpp:44:11: error: Not supported on this platform.
  hwDigitalWrite(MY_RF24_CE_PIN, level);
           ^
./drivers/RF24/RF24.cpp:388:11: error: Not supported on this platform.
  hwPinMode(MY_RF24_CE_PIN,OUTPUT);
           ^
./drivers/RF24/RF24.cpp:389:11: error: Not supported on this platform.
  hwPinMode(MY_RF24_CS_PIN,OUTPUT);
           ^
./drivers/RF24/RF24.cpp:37:32: warning: unused parameter ‘level’ [-Wunused-parameter]
 LOCAL void RF24_csn(const bool level)
                                ^
./drivers/RF24/RF24.cpp:42:31: warning: unused parameter ‘level’ [-Wunused-parameter]
 LOCAL void RF24_ce(const bool level)
                               ^
./drivers/RF24/RF24.cpp: In function ‘uint8_t RF24_spiMultiByteTransfer(uint8_t, uint8_t*, uint8_t, bool)’:
./drivers/RF24/RF24.cpp:56:11: error: ‘LOW’ was not declared in this scope
  RF24_csn(LOW);
           ^
./drivers/RF24/RF24.cpp:99:11: error: ‘HIGH’ was not declared in this scope
  RF24_csn(HIGH);
           ^
./drivers/RF24/RF24.cpp: In function ‘void RF24_startListening()’:
./drivers/RF24/RF24.cpp:235:10: error: ‘HIGH’ was not declared in this scope
  RF24_ce(HIGH);
          ^
./drivers/RF24/RF24.cpp: In function ‘void RF24_stopListening()’:
./drivers/RF24/RF24.cpp:241:10: error: ‘LOW’ was not declared in this scope
  RF24_ce(LOW);
          ^
./drivers/RF24/RF24.cpp: In function ‘void RF24_powerDown()’:
./drivers/RF24/RF24.cpp:251:10: error: ‘LOW’ was not declared in this scope
  RF24_ce(LOW);
          ^
./drivers/RF24/RF24.cpp: In function ‘bool RF24_sendMessage(uint8_t, const void*, uint8_t)’:
./drivers/RF24/RF24.cpp:269:10: error: ‘HIGH’ was not declared in this scope
  RF24_ce(HIGH);
          ^
./drivers/RF24/RF24.cpp:276:10: error: ‘LOW’ was not declared in this scope
  RF24_ce(LOW);
          ^
./drivers/RF24/RF24.cpp: In function ‘bool RF24_initialize()’:
./drivers/RF24/RF24.cpp:395:10: error: ‘LOW’ was not declared in this scope
  RF24_ce(LOW);
          ^
./drivers/RF24/RF24.cpp:396:11: error: ‘HIGH’ was not declared in this scope
  RF24_csn(HIGH);
           ^
Makefile:114: recipe for target 'build/examples_linux/mysgw.o' failed
make: *** [build/examples_linux/mysgw.o] Error 1
root@OrangePI:~/marceloaqno-spidev#

i want build a gateway with orangepi one with channel 0 . what am i do ? thank you

marceloaqno

@Reza You need to run:

modprobe gpio-sunxi

so that /sys/class/gpio/export is created.

marceloaqno

@Tag Does the TMRh20 works in the way your radio is currently connected?

Tag

@marceloaqno
The library compiled, but unfortunately i cannot get the examples for linux working.
need to edit i.e. gettingstarted.cpp with the correct pin setting, have tried a lot, but either it says that the radio is not connected, and if used with incorrect settings it will not compile at all....

Maybe someone following this thread who has experince with this lib?
if there is any progress from my side will keep you posted...

mihai.aldea

If you used this wiring scheme:

nRF24L01 | Orange Pi
_________|________________
VCC      | VCC3V3-EXT
GND      | GND
CSN      | SPI0_CS0 (SPI-CE0)
CE       | PA7 (IO-7)
MOSI     | SPI0_MOSI (SPI-MOSI)
SCK      | SPI0_CLK (SPI-CLK)
MISO     | SPI0_MISO (SPI-MISO)

Then you should initialize the radio with:

RF24 radio(7,0);

Worked for me:

root@opi-pc-1:~/RF24-master/examples_linux# ./gettingstarted
RF24/examples/GettingStarted/
STATUS		 = 0x0e RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=7 TX_FULL=0
RX_ADDR_P0-1	 = 0x65646f4e32 0x65646f4e31
RX_ADDR_P2-5	 = 0xc3 0xc4 0xc5 0xc6
TX_ADDR		 = 0x65646f4e32
RX_PW_P0-6	 = 0x20 0x20 0x00 0x00 0x00 0x00
EN_AA		 = 0x3f
EN_RXADDR	 = 0x02
RF_CH		 = 0x4c
RF_SETUP	 = 0x07
CONFIG		 = 0x0e
DYNPD/FEATURE	 = 0x00 0x00
Data Rate	 = 1MBPS
Model		 = nRF24L01+
CRC Length	 = 16 bits
PA Power	 = PA_MAX

 ************ Role Setup ***********
Choose a role: Enter 0 for pong_back, 1 for ping_out (CTRL+C to exit)

marceloaqno

@mihai.aldea Could you try the repo I'm working on (https://github.com/marceloaqno/MySensors/tree/spidev marceloaqno-spidev) adding your settings to the examples_linux/mysgw.cpp?

#define MY_RF24_CE_PIN 7
#define MY_RF24_CS_PIN 0

Tag

@mihai.aldea

Hmmm.... checked the docs again and guess what. the 26 pin header on the OPI Zero has SPI1.... instead of SPI0

Expansion Port

The Orange Pi Zero has a 26-pin, 0.1" unpopulated connector with several low-speed interfaces.
2x13 Header
1	3.3V	           2	5V
3	TWI0_SDA / PA12	   4	5V
5	TWI0_SCK / PA11	   6	GND
7	PWM1 / PA06	       8	UART1_TX / PG06
9	GND	               10	UART1_RX / PG07
11	UART2_RX / PA01	   12	SIM_CLK/PA_EINT7 / PA07
13	UART2_TX / PA00	   14	GND
15	UART2_CTS / PA03   16	TWI1-SDA / PA19
17	3.3V	           18	TWI1-SCK / PA18
19	SPI1_MOSI / PA15   20	GND
21	SPI1_MISO / PA16   22	UART2_RTS / PA02
23	SPI1_CLK / PA14    24	SPI1_CS / PA13
25	GND	               26	SIM_DET/PA_EINT10 / PA10

From http://linux-sunxi.org/Xunlong_Orange_Pi_Zero
If i look at /dev I only see spi0, which is most probably used for the onboard flash...

root@orangepizero:/# ll /dev | grep -i spi
crw------- 1 root root    153,   0 Jan  8 11:12 spidev0.0

So now i need to figure out a way to get SPI1 up and running

mihai.aldea

@marceloaqno Here's the output:

./MySensors.h:258:2: error: #error No support for nRF24 radio on this platform
 #error No support for nRF24 radio on this platform
  ^
In file included from ./drivers/RF24/RF24.cpp:23:0,
                 from ./MySensors.h:294,
                 from examples_linux/mysgw.cpp:77:
./drivers/RF24/RF24.h:52:17: fatal error: SPI.h: No such file or directory
 #include <SPI.h>
                 ^
compilation terminated.
Makefile:98: recipe for target 'build/examples_linux/mysgw.o' failed
make: *** [build/examples_linux/mysgw.o] Error 1

mihai.aldea

@Tag Use this info:
http://linux-sunxi.org/Sunxi-tools
To export /boot/script.bin, edit the output file and enable SPI1, then compile it back and reboot your OPi with the SPI1 active.

If you haven't done this before, it's quite simple.

apt-get install sunxi-tools
cd ~
bin2fex /boot/script.bin > script.fex

Edit the script.fex file, find the [spi1] section and change spi_used = 0 to spi_used = 1. Save the file and exit.
Then

fex2bin script.fex > /boot/script.bin

Reboot, then you should have the SPI1 active.

Reza

@marceloaqno
i have error yet
orangepi is a good board. please work at this board and run mysensors gateway on this, i follow this topic when you can fix this on orange pi . thank you

Tag

@mihai.aldea

Yep already found it :) problem was the old version of the tools, it was not able to decompile the script.bin file...

[update]

modified the script file,
changed spi_used = 1
compiled back and rebooted

just 1 device file in called spidev0.0 no new device files are created..... :(

dmesg output:

[    0.814287] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
[    0.814316] sunxi_spi_chan_cfg()1376 - [spi-1] has no spi_regulator.
[    0.815569] spi spi0: master is unqueued, this is deprecated
[    0.816776] spi spi1: master is unqueued, this is deprecated

Thx, will keep you posted!

Mysensors Gateway on OrangePi (Zero) (opi)

9

11.7k

11.2k

113.0k