Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Convert roller blinds to motorised

mjdula last edited by

Any know or can show me how to motorise my manual roller blinds?
Reply Quote 0
1 Reply Last reply
korttoma Hero Member last edited by

Search is your friend -> https://forum.mysensors.org/topic/157/diy-blind-control-motor
Reply Quote 0
1 Reply Last reply

2
Posts

1376
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

11

0
Votes

11
Posts

53
Views

@dpcons MQTT sounds intimidating and looks imitimidating when you see all of the options available. Here's the scenario: You want to send a message. That's the -m option followed by a space and the message between " " the location, topic, is a tree, -t option, separated by forward slash / eg. MyRootTopic/MyTopicsSub/MyTopicSubSub It's as easy as that if your broker, the MQTT service (program) is on the same computer as the sending program. Usually it's not. Specifiy the location, the host, of the broker with the -h option followed by the host name or IP address The retain option, -r is important but explaining it is beyone the scope of this message Receiving, subscribing, to a topic is just the same, but you wouldn't have the -m message If you subscribe from the command line, the subscribe function waits indefinitely for messages published to the subscribed topic (unless you use the -C option) ^C to terminate the command. A tamotized device with the MQTT configured will create a number of topics on the broker. Home Assistant will see this automatically, if you have the Tasmota and MQTT Integrations installed. The MySensors MQTT gateway takes care of MQTT communication for a MySensors device. Again the MySensors and MQTT integrations. I use both. -OSD
Adding Listen only device to my system.
Development • • dpcons

5

0
Votes

5
Posts

19
Views

@mfalkvidd Thanks for the info!
PJON and Minicore not working
Development • • Trand

1

0
Votes

1
Posts

14
Views

No one has replied
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

29
Views

@OldSurferDude yes, just run the configure command with --my-transport=none
Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

3

0
Votes

3
Posts

21
Views

@mfalkvidd Yes, I understand that 253 is the software limit. I was wondering about the hardware limit. For example, my Asus router has a software limit of 253 devices. But when I get 20-25 WiFi devices trying to connect, the network goes haywire. (pun intended ) I am quite convinced that this is a hardware limitation of the router because the router has to carry some information about each connection. If the gateway is dumb, that is, carries no information about any connection, then it could truly have 253 connections. After a bit of contemplation, I realize that the name, gateway, implies this. If that is the case, it is good news for the DiY'er in that this very inexpensive and cheap hardware could stand in for a LoRaWAN, again, with a number of compromises.

Convert roller blinds to motorised

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Adding Listen only device to my system.
Development • • dpcons

PJON and Minicore not working
Development • • Trand

Gateway without a radio
Development • • OldSurferDude

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

17
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Convert roller blinds to motorised

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

MQTT-Help me understand about the MQTT Gateway. Development • • dpcons

Adding Listen only device to my system. Development • • dpcons

PJON and Minicore not working Development • • Trand

Gateway without a radio Development • • OldSurferDude

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors Development • • OldSurferDude

17Online

11.7kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

Adding Listen only device to my system.
Development • • dpcons

PJON and Minicore not working
Development • • Trand

Gateway without a radio
Development • • OldSurferDude

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

17
Online

11.7k
Users

11.2k
Topics

113.0k
Posts