💬 NodeManager
-
@user2684 i just mean, we have to put this is the documentation.
currently i have a strange problem:
the Motion Sensors doesnt reset. I checked with my old Motion sketch and everything is fine.
Only sends the Value "1".11132 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1
16513 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1
26243 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1 -
@user2684 i just mean, we have to put this is the documentation.
currently i have a strange problem:
the Motion Sensors doesnt reset. I checked with my old Motion sketch and everything is fine.
Only sends the Value "1".11132 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1
16513 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1
26243 TSF:MSG:SEND,1-1-0-0,s=2,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1@felix-haverkamp got it, thanks, I've opened this issue https://github.com/mysensors/NodeManager/issues/366.
Regarding the sensor motion, weird, by default should attach to CHANGE interrupt so to intercept both. Any chance to share NodeManager's debug log as well? Thanks
-
@felix-haverkamp got it, thanks, I've opened this issue https://github.com/mysensors/NodeManager/issues/366.
Regarding the sensor motion, weird, by default should attach to CHANGE interrupt so to intercept both. Any chance to share NodeManager's debug log as well? Thanks
@user2684
i think conditional report is the problem:#define FEATURE_CONDITIONAL_REPORT ON
without it works fine.
-
Every new version of NodeManager, I try to review and hopefully improve its architecture. This time looked like a simple and quick task but eventually ended up in a complete and deep review of the code. Many many many things have changed with the main objective to better integrate with the MySensors library and simplify the life of users willing to contribute or to add support for new sensors.
The new file structure (with a dedicated file for each supported sensor) and the way the package is delivered (as an arduino library now) go into this direction. There are also included a good amount of new features but still in most of the cases, resulting a smaller code.
All the details are available at https://github.com/mysensors/NodeManager/pull/391 which will be merged into the development branch shortly.
Due to the many changes, if anybody would be willing to give it a try and report any bug, would be really great. Thanks!
-
Just wanted to say that NodeManager is awesome. I can't believe I only now really had a better look at what it is. I always thought it was some kind of software you had to install, and that it was used by professionals to manage complicated sensor nets.
For the last few months I've been thinking "wouldn't it be useful if there was some kind of beginner friendly web interface where you could select which devices you want, and then it creates the code for you". This is so close to that. Thank you for this incredible work!
-
Just wanted to say that NodeManager is awesome. I can't believe I only now really had a better look at what it is. I always thought it was some kind of software you had to install, and that it was used by professionals to manage complicated sensor nets.
For the last few months I've been thinking "wouldn't it be useful if there was some kind of beginner friendly web interface where you could select which devices you want, and then it creates the code for you". This is so close to that. Thank you for this incredible work!
-
Is it possible to "force" send SensorDoor value regularly?
I am using magnetic sensor together with interrupt feature but when sensor status is change too fast before main loop is finished, sensor value remains in wrong state until magnetic sensor value is physically changed again.
So I would like to set that SensorDoor value will be set regularly like e.g. temperature sensors values. I tried to add:
door.setReportIntervalMinutes(5);But it does not work in this case. Value is not reported based on this interval. Only way how to get SensorDoor value back to right state is physically change its value (open/close magnetic sensors).
Btw Nodemanager is really awsome. Great work!
-
Hi, I need some advice for my following problem..:
Situation: Arduino ist connected to an raspberry gateway with openhab -> works just fine.
To the arduino I have connected a PIR on 3 and a photoresistor (LDR) with an 10k resistor on A0 -> works just fine.
On first boot (after connecting etc.) the arduino sends motion status + LDR value. But after that first msg. only the motion (tripped) is send.
What I want: I want that the arduino sleeps until there is an interrupt comming from the PIR and then sends the motion status+light value (LDR) and then sleeps again 4ever until the next interrupt.
Problem: As I said, it only sends the light value only once.. and then never again. On the arduino debug I can see, that only motion is send:
NodeManager v1.7
LIB V=2.3.0 R=N E=X T=N A=A S=S B=-
LDR I=1 P=16 T=23
MOTION I=2 P=1 T=16
RADIO...OK
PRES I=1 T=16 D=LDR
PRES I=2 T=1 D=MOTION
READYMY I=5 M=255
INT P=3, V=0
INT P=3 M=1
INT P=2 M=255
MOTION I=2 P=3 V=0
SEND D=0 I=2 C=0 T=16 S= I=0 F=0.00
LDR I=1 V=352 %=34 <-- first an last time LDR sends it's value
SEND D=0 I=1 C=0 T=23 S= I=0 F=0.00
INT P=3, V=1
MOTION I=2 P=3 V=1
SEND D=0 I=2 C=0 T=16 S= I=0 F=0.00
INT P=3, V=0
MOTION I=2 P=3 V=0
SEND D=0 I=2 C=0 T=16 S= I=0 F=0.00
...
Hope you can help me :grimacing: many thanks in advance :-)// General settings #define SKETCH_NAME "Test2" #define SKETCH_VERSION "1.0" //#define MY_DEBUG // NRF24 radio settings #define MY_RADIO_NRF24 #define MY_SIGNING_SIMPLE_PASSWD "xxx" #define MY_ENCRYPTION_SIMPLE_PASSWD "xxx" #define MY_RF24_PA_LEVEL RF24_PA_HIGH #define MY_RF24_CHANNEL (124) // Advanced settings #define MY_BAUD_RATE 9600 //#define MY_SMART_SLEEP_WAIT_DURATION_MS 500 #define MY_SPLASH_SCREEN_DISABLED /*********************************** * NodeManager modules for supported sensors */ #define USE_ANALOG_INPUT #define USE_INTERRUPT /*********************************** * NodeManager built-in features */ // Enable/disable NodeManager's features #define FEATURE_DEBUG ON #define FEATURE_POWER_MANAGER OFF #define FEATURE_INTERRUPTS ON #define FEATURE_CONDITIONAL_REPORT OFF #define FEATURE_EEPROM OFF #define FEATURE_SLEEP ON #define FEATURE_RECEIVE OFF #define FEATURE_TIME OFF #define FEATURE_RTC OFF #define FEATURE_SD OFF #define FEATURE_HOOKING OFF /*********************************** * Load NodeManager Library */ #include "NodeManagerLibrary.h" NodeManager node; /*********************************** * Add your sensors below */ // Attached sensors SensorLDR ldr(node,A0); //SensorInterrupt interrupt(node,3); SensorMotion motion(node,3); /*********************************** * Main Sketch */ // before void before() { // setup the serial port baud rate Serial.begin(MY_BAUD_RATE); /* * Configure your sensors below */ node.setReportIntervalSeconds(10); node.setSleepSeconds(60); /* * Configure your sensors above */ node.before(); } // presentation void presentation() { // call NodeManager presentation routine node.presentation(); } // setup void setup() { // call NodeManager setup routine node.setup(); } // loop void loop() { // call NodeManager loop routine node.loop(); } #if FEATURE_RECEIVE == ON // receive void receive(const MyMessage &message) { // call NodeManager receive routine node.receive(message); } #endif #if FEATURE_TIME == ON // receiveTime void receiveTime(unsigned long ts) { // call NodeManager receiveTime routine node.receiveTime(ts); } #endif -
Hi, I need some advice for my following problem..:
Situation: Arduino ist connected to an raspberry gateway with openhab -> works just fine.
To the arduino I have connected a PIR on 3 and a photoresistor (LDR) with an 10k resistor on A0 -> works just fine.
On first boot (after connecting etc.) the arduino sends motion status + LDR value. But after that first msg. only the motion (tripped) is send.
What I want: I want that the arduino sleeps until there is an interrupt comming from the PIR and then sends the motion status+light value (LDR) and then sleeps again 4ever until the next interrupt.
Problem: As I said, it only sends the light value only once.. and then never again. On the arduino debug I can see, that only motion is send:
NodeManager v1.7
LIB V=2.3.0 R=N E=X T=N A=A S=S B=-
LDR I=1 P=16 T=23
MOTION I=2 P=1 T=16
RADIO...OK
PRES I=1 T=16 D=LDR
PRES I=2 T=1 D=MOTION
READYMY I=5 M=255
INT P=3, V=0
INT P=3 M=1
INT P=2 M=255
MOTION I=2 P=3 V=0
SEND D=0 I=2 C=0 T=16 S= I=0 F=0.00
LDR I=1 V=352 %=34 <-- first an last time LDR sends it's value
SEND D=0 I=1 C=0 T=23 S= I=0 F=0.00
INT P=3, V=1
MOTION I=2 P=3 V=1
SEND D=0 I=2 C=0 T=16 S= I=0 F=0.00
INT P=3, V=0
MOTION I=2 P=3 V=0
SEND D=0 I=2 C=0 T=16 S= I=0 F=0.00
...
Hope you can help me :grimacing: many thanks in advance :-)// General settings #define SKETCH_NAME "Test2" #define SKETCH_VERSION "1.0" //#define MY_DEBUG // NRF24 radio settings #define MY_RADIO_NRF24 #define MY_SIGNING_SIMPLE_PASSWD "xxx" #define MY_ENCRYPTION_SIMPLE_PASSWD "xxx" #define MY_RF24_PA_LEVEL RF24_PA_HIGH #define MY_RF24_CHANNEL (124) // Advanced settings #define MY_BAUD_RATE 9600 //#define MY_SMART_SLEEP_WAIT_DURATION_MS 500 #define MY_SPLASH_SCREEN_DISABLED /*********************************** * NodeManager modules for supported sensors */ #define USE_ANALOG_INPUT #define USE_INTERRUPT /*********************************** * NodeManager built-in features */ // Enable/disable NodeManager's features #define FEATURE_DEBUG ON #define FEATURE_POWER_MANAGER OFF #define FEATURE_INTERRUPTS ON #define FEATURE_CONDITIONAL_REPORT OFF #define FEATURE_EEPROM OFF #define FEATURE_SLEEP ON #define FEATURE_RECEIVE OFF #define FEATURE_TIME OFF #define FEATURE_RTC OFF #define FEATURE_SD OFF #define FEATURE_HOOKING OFF /*********************************** * Load NodeManager Library */ #include "NodeManagerLibrary.h" NodeManager node; /*********************************** * Add your sensors below */ // Attached sensors SensorLDR ldr(node,A0); //SensorInterrupt interrupt(node,3); SensorMotion motion(node,3); /*********************************** * Main Sketch */ // before void before() { // setup the serial port baud rate Serial.begin(MY_BAUD_RATE); /* * Configure your sensors below */ node.setReportIntervalSeconds(10); node.setSleepSeconds(60); /* * Configure your sensors above */ node.before(); } // presentation void presentation() { // call NodeManager presentation routine node.presentation(); } // setup void setup() { // call NodeManager setup routine node.setup(); } // loop void loop() { // call NodeManager loop routine node.loop(); } #if FEATURE_RECEIVE == ON // receive void receive(const MyMessage &message) { // call NodeManager receive routine node.receive(message); } #endif #if FEATURE_TIME == ON // receiveTime void receiveTime(unsigned long ts) { // call NodeManager receiveTime routine node.receiveTime(ts); } #endif@fausti
ok, I have solved it myself - the PIR made all that trouble.
I did connect the PIR on 3.3V (similar to https://forum.mysensors.org/uploads/upload-4bdca27e-3c36-4c68-9e54-947b9f4717b4.jpg).Problem was, that when arduino wakes up the radio, the power drop would kinda restart the PIR, which causes an interrupt. Think a similar problem was discussed here:
https://forum.mysensors.org/topic/6511/hc-sr501-3-3v-randomly-sends-tripped-when-radio-is-onAnyways - you surly would have helped, if i would not have found it. Great forum! :-)
-
Is it possible to "force" send SensorDoor value regularly?
I am using magnetic sensor together with interrupt feature but when sensor status is change too fast before main loop is finished, sensor value remains in wrong state until magnetic sensor value is physically changed again.
So I would like to set that SensorDoor value will be set regularly like e.g. temperature sensors values. I tried to add:
door.setReportIntervalMinutes(5);But it does not work in this case. Value is not reported based on this interval. Only way how to get SensorDoor value back to right state is physically change its value (open/close magnetic sensors).
Btw Nodemanager is really awsome. Great work!
@jiri-hron I think you can achieve what you need by using FEATURE_TIME. In this way when woken up, NodeManager will go back to sleep only for the remainder time left. Not ideal but I couldn't find a better way to understand for how long the node has been sleeping before the interrupt.
-
It looks like there is a limit of 1 type of each sensor. Is there a way to modify this?
My use-case is a french sliding glass door. I would like to use a single node with 2 magnetic sensors (one on each end of the node) with the node mounted in the middle of the door, so that if either side is moved the interrupt is triggered.
-
It looks like there is a limit of 1 type of each sensor. Is there a way to modify this?
My use-case is a french sliding glass door. I would like to use a single node with 2 magnetic sensors (one on each end of the node) with the node mounted in the middle of the door, so that if either side is moved the interrupt is triggered.
@iteafreely your understanding is correct. I see two options here: you can either create a new custom sensor inheriting from SensorDoor and adding an additional child and the extra logic you require or create two instances of SensorDoor and playing with hooking functions to make one checking on the other. In this latter case you probably need some additional variables to keep track of the status.
-
@iteafreely I don't think there is a limit of one sensor per type, not even for interrupts like door sensors. You just need to make sure you are using different pins and different child ids for the two magnetic sensors. I'm using 8 analog sensors (MQ-... gas sensors) on eight different pins on the same node and it works just fine.
Of course, if you need some interdependence on what the two magnetic sensors report, then you must follow @user2684's suggestion of creating a custom sensor (a C++ class derived from an existing sensor class).
But if you simply want two independent magnetic sensors (for each of the ends of your sliding door), then you can simply create two instances of SensorDoor on two different pins (here pins 3 and 4) and different hardcoded child_id (1 and 2 in this case):SensorDoor doorLeft(node,3,1); SensorDoor doorRight(node, 4,2);Unfortunately, both of them will report to the gateway with name "DOOR" (and there's no way to change it without subclassing SensorDoor), but they will have a different child_id 1 and 2 to distinguish the two values sent by the node.
You can then use your smart home controller to handle the two door sensors like one.
-
It looks like there is a limit of 1 type of each sensor. Is there a way to modify this?
My use-case is a french sliding glass door. I would like to use a single node with 2 magnetic sensors (one on each end of the node) with the node mounted in the middle of the door, so that if either side is moved the interrupt is triggered.
@iteafreely Not sure of software issues as I don't use NodeManager, but your use-case indicates you do not need to know which door is opened, only that one or both is/are.
If by magnetic sensor you mean magnet/reed, would a single reed where both doors meet, or two reeds (one on each door end) wired in parallel, to a single interrupt pin not provide this? -
@iteafreely I don't think there is a limit of one sensor per type, not even for interrupts like door sensors. You just need to make sure you are using different pins and different child ids for the two magnetic sensors. I'm using 8 analog sensors (MQ-... gas sensors) on eight different pins on the same node and it works just fine.
Of course, if you need some interdependence on what the two magnetic sensors report, then you must follow @user2684's suggestion of creating a custom sensor (a C++ class derived from an existing sensor class).
But if you simply want two independent magnetic sensors (for each of the ends of your sliding door), then you can simply create two instances of SensorDoor on two different pins (here pins 3 and 4) and different hardcoded child_id (1 and 2 in this case):SensorDoor doorLeft(node,3,1); SensorDoor doorRight(node, 4,2);Unfortunately, both of them will report to the gateway with name "DOOR" (and there's no way to change it without subclassing SensorDoor), but they will have a different child_id 1 and 2 to distinguish the two values sent by the node.
You can then use your smart home controller to handle the two door sensors like one.
-
@user2684 Right, thanks for pointing this out. I mixed up the child name that was sent to the controller (which can be changed by e.g.
void before() { ... doorLeft.children.get(1)->setDescription("Door Left"); doorRight.children.get(1)->setDescription("Door Right"); node.before(); }) and the sensor's _name field, which is printed to the debug output. That "DOOR" debug output cannot be changed without subclassing. But as this is just debug output, it's just a minor nuissance.
-
@user2684 Right, thanks for pointing this out. I mixed up the child name that was sent to the controller (which can be changed by e.g.
void before() { ... doorLeft.children.get(1)->setDescription("Door Left"); doorRight.children.get(1)->setDescription("Door Right"); node.before(); }) and the sensor's _name field, which is printed to the debug output. That "DOOR" debug output cannot be changed without subclassing. But as this is just debug output, it's just a minor nuissance.
@reinhold oh you're right I didn't even noticed that DOOR would show up in the debug output, thanks. Anyway with v1.8-dev this should have gone since debug output has been completely re-worked (and made compatible with https://www.mysensors.org/build/parser). Thanks
-
hello, I wanted to use the function for FEATURE_CONDITIONAL_REPORT for an LDR sensor but except a value when starting the arduino, no more values are transferred, must be configured for the function specifically something? Node manager 1.8dev
@mhofer a few issues came out with conditional reporting during some recent tests, https://github.com/mysensors/NodeManager/pull/430 just merged into development should have solved them. Could you please give it a try? Thanks!
-
Hello all, NodeManager v1.8 is almost ready and likewise with the previous releases I like to give brave users a few weeks to test it out before actually releasing it. If you are one of those, download it from https://github.com/mysensors/NodeManager/tree/development; for a full list of changes, have a look at https://github.com/mysensors/NodeManager/projects/2.
Of course feel free to open a ticket on Github for any issue you could come across. Thanks!
