nRF5 action!

[Mike_Lemo]

how'd you program this blank nrf52832 chip with an SWD programmer like the ST link v2 what programming environment to use and so on?

[NeverDie]

@Mike_Lemo
I had no luck using the ST link v2 from Windows. You might be luckier, or you might try using it from Linux. However, as discussed above, I have had success using the nRF52832 DK and the Arduino IDE from Windows. That's how I intend to program the nRF52832 module using the breakout board I posted above.

[mtiutiu]

@Mike_Lemo

I used the Arduino IDE with sandeepmistry arduino core installed and I managed to program a nrf51822 module with success. I used a cheap st-link programmer from AliExpress. I don't know about nrf52832 as I don't have one. But I don't see why it wouldn't work. You need 4 wires: Vdd(3.3V), GND, SWD and SWCLK.
From Arduino IDE you need to select st-link as programmer.
It uses openocd under the hood to do the work and it worked both on Windows and Linux. On Linux you might need to set udev rules for allowing regular user to use the st-link.

[NeverDie]

@mtiutiu said in nRF5 Bluetooth action!:

I managed to program a nrf51822 module with success.

Did you power the nrf51822 through the st-link programmer, or did you power it independently?

[Mike_Lemo]

@mtiutiu And when you want to program an independent chip with the ST link V2 do you just chose "generic nrf52"?

Also how is it possible to connect between through two NRF52s in slave master config?
Is it possible to take advantage of the NFC functionality with that programming environment?

[NeverDie]

Good news! I received my second nRF52832 DK today, so now I can have a DK on both ends of a link. Bottom line: I ran some quick tests, and it has much better range than the Adafruit nRF52832 Feather.

Whew! What a relief. The Adafruit had very disappointing range. In contrast, and as expected, the two DK's have better range than regular nRF24L01+ radios.

[Mike_Lemo]

@NeverDie How did you manage to send and receive data between these two units? may you share the code with us?

[NeverDie]

@Mike_Lemo
I'm simply using the GatewaySerial and the LightSensor sketches from the mysensors developers release. Just make the following change in each sketch:

//#define MY_RADIO_NRF24
#define MY_RADIO_NRF5_ESB

[mtiutiu]

@NeverDie

Powered from st-link programmer.

[mtiutiu]

@Mike_Lemo

I used generic and no soft device as Mysensors doesn't use soft devices. I don't know about master-slave, didn't used such a configuration.

You need to create another variant for other pin definitions as this is the way arduino framework works as far as I know.

Never used NFC so I can't give you hints on that, sorry.

[NeverDie]

Looks as though these guys came up with a fairly easy way to develop using actual bluetooth low energy: http://mklec.com/project-kits/kd-circuits/bluetooth-low-energy-board-anaren-A20737-module

Unfortunately, I don't believe it runs on the nRF5 though.

[NeverDie]

More good news! I was able to program a Sparkfun nrf52832 board using the DK, and its range is better than the Adafruit nRF52832 Feather and also better than an nRF24L01+.

So, my provisional conclusion is to avoid chip antennas, such as Adafruit is using, if better range is desired.

@NeverDie said in nRF5 Bluetooth action!:

Looks as though the nRF52832 sparkfun board has more of a conventional trace antenna:

though isn't it somewhat odd that it appears to also be directly connected to the ground plane(?), or at least a copper pour. Is that normal? This was one of the images produced by sending their .BRD file to oshpark, so that I could get a look at the antenna.

Also, this now gives me a "known good" platform, namely the Sparkfun nRF52832 board, to order PCB's for and try to see if I can successfully solder on any of the bonus nRF52832 chips I received with my two DK's.

[NeverDie]

Apparently you can now run micropython on an nRF52832 board:
https://www.youtube.com/watch?v=50ImTDRREnU

It's still early days, but it sounds like fun. For one thing, since it's a dynamic language, OTA updates should be easy!

[Terrence]

@NeverDie Wow, that it really good news. I was following Tony's videos on mpy on the ESP chips, but had not checked back lately.

[NeverDie]

@Nca78 said in nRF5 Bluetooth action!:

For shipment delay I wouldn't be surprised if they shipped the same way with free option and it would just be a different way to state the delay on the 2 websites...

You were right: I received both the ebay and the aliexpress packages today. Even for e-packet, that's pretty fast shipping! In fact, they arrived before any of the other items I ordered from other vendors. So, at least that part went well.

[NeverDie]

Does the E73-2G4M04S require anything extra in order to be programmed?

Today I tried programming it the same way that I have successfully with both the adafruit and the Sparkfun nRF52832 boards using the DK, but the DK keeps complaining that the E73-2G4M04S may not be connected.

[Nca78]

@NeverDie if I remember well in the datasheet they say you have to put the softdevice on it first.

[NeverDie]

Yeah, here's what it says:

1. The module embedded with ARM MCU. For program downloading, please use the J-LINK downloader, any other serial port or JTAG、ISP、ICP are
   unavailable to download.
2. There’s two parts to download the program. Because the protocol stack
   of NORDIC is not programmed yet, so users need to use the official nRFgo
   studio of NORDIC to program the protocol stack first, then program the hex of application code. Or, to program the protocol stack of NORDIC first and
   download via the IAR or KEIL.

Seems odd, but I'll give it a try.

[NeverDie]

It's not clear whether the DK can/should be used for this part of it, as it's unclear (at least to me) whether it will end up altering the target chip or the DK. I'm just not sure. So, to do at least this ambiguous part of it, I'll first check whether or not the nRFgo studio software will work with one of the other programmers I've collected (not the DK). That may take a while...

[mtiutiu]

@NeverDie

Why don't you try to program it with a st-link programmer and arduino ide with sandeepmistry nrf5 core installed? I bought that module(E73-2G4M04S) too and I want to know how this part goes. Thanks.