NRF24L01+ problems in 2.1.1 and 2.2.0 Beta

gohan

Did you try to compile it as ethernet gw?

miljume

This post is deleted!

miljume

@gohan Yes, I have tried compiling it as Ethernet GW but that didn't work either

Output:

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: New connection from 127.0.0.1
mysgw: Client 0 connected
mysgw: Client 0: 0;0;3;0;2;
mysgw: Client 0: 0;0;3;0;2;Get Version
mysgw: Client 0: 0;0;3;0;18;PING
mysgw: TSF:MSG:READ,0-0-0,s=0,c=3,t=18,pt=0,l=4,sg=0:PING
mysgw: !TSF:MSG:LEN,0!=11
mysgw: TSF:MSG:READ,0-0-0,s=0,c=3,t=18,pt=0,l=4,sg=0:PING
mysgw: !TSF:MSG:LEN,0!=11

Then the GW repeats the last 2 lines forever

Compiled it with IP 127.0.0.1 for the controller and port 5003

It does not pick up the sensors and values

If I compile it with the local IP of the controller I get the following errors

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: Eth: connect
mysgw: connect: Connection refused

After that the last 2 lines repeats forever

mfalkvidd

@miljume 2.1.1 has been out for many months without problem, so it is not likely that there is a problem with the MySensors library. But you could of course have stumbled on a corner case that no-one has seen before.

Could you post the full debug log for the gateway and the full configure command you used to compile it?

Edit: sorry, I see that you have the full log in a later post. So just post the configure command and branch/version used for each output.

miljume

@mfalkvidd Sure, below are commands and debug logs for both 2.1.1 and 2.2.0 Beta

As you can see both of the Gateways fails with 2.1.1. I have seen other people having the exact same problem so that is why I thought it could be something with the libraries

Commands with 2.2.0 Beta (serial GW)

./configure --my-transport=nrf24
./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020
make

Debug Log

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

Domoticz Log

2017-10-10 18:43:07.538 MySensors: Using serial port: /dev/ttyUSB020
2017-10-10 18:43:07.538 Error: Serial Port closed!... Error: End of file
2017-10-10 18:43:08.538 MySensors: retrying in 30 seconds...

Repeats every 30th second,

Commands with 2.2.0 Beta (Ethernet GW)

./configure --my-transport=nrf24
./configure --my-gateway=ethernet --my-port=5003
./configure --my-gateway=ethernet --my-controller-ip-address=127.0.0.1
make

Debug Log

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: Eth: connect
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: Eth: connect

Commands with 2.1.1 (serial GW)

./configure --my-transport=nrf24
./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020
make

Debug Log

mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT

Commands with 2.1.1 (Ethernet GW)

./configure --my-transport=nrf24
./configure --my-gateway=ethernet --my-port=5003
./configure --my-gateway=ethernet --my-controller-ip-address=127.0.0.1
make

Debug Log

mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT

mfalkvidd

@miljume thanks. And yes, there seems to be something fishy going on since other people also have problems.

I don't have a spare raspberry pi at the moment so I can't reproduce the problem. Hopefully someone else can help troubleshooting. I'll try to get my hands on a new raspberry within a week.

gohan

@miljume said in NRF24L01+ problems in 2.1.1 and 2.2.0 Beta:

./configure --my-transport=nrf24
./configure --my-gateway=ethernet --my-port=5003

it should be on a single line like this

./configure --my-transport=nrf24 --my-gateway=ethernet --my-port=5003

--my-controller-ip-address=127.0.0.1 is not needed

miljume

@gohan Thanks, will try that as soon as I can

Yveaux

@miljume I've seen the same length errors in the past when my radio wiring wasn't stable (flaky jumper wires). The TSP Fail messages indicate the same.
Could you check your connections from the pi to the radio?

miljume

@Yveaux Thanks for the feedback but I am using a RPI Shield so the connections should be stable

wergeld

@miljume I am having the same issue since 2.1 and trying to revert to 2.2 beta it fails as well. I am using an RPi model 2 B and the same RPI shield (I have traded out the shield as I have a few and same result). All of my nodes have been offline for months as the gateway does not function.

gohan

I remember there was a bug in the library for rpi2 but I can't remember the details

wergeld

@gohan That bug had to do with the chipset but that was resolved i think.

miljume

@gohan Now I have tried compiling it with one line command but the GW still don't start with 2.1.1

./configure --my-transport=nrf24 --my-gateway=ethernet --my-port=5003

mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT

Yveaux

@miljume I see alternating !TSM:INIT:TSP Fail and TSM:INIT:TSP OK in your logs.
The fails indicate a failure to communicate with the radio module.
Is there a pattern in these fails between software versions?

miljume

@Yveaux The FAIL´s all occur with 2.1.1 and the OK is with 2.2.0 Beta. Same radio connections for both so the FAIL´s should not be connected to communication with the radio module. I have also tried 3 radios and 2 different ways of connecting them (Shield and Dupont cables) Even if 2.2.0 starts OK the problem is that it for the Ethernet GW it fails to connect

mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: Eth: connect
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: Eth: connect

And for the Serial GW it gives the following error in Domoticz

2017-10-10 18:43:07.538 MySensors: Using serial port: /dev/ttyUSB020
2017-10-10 18:43:07.538 Error: Serial Port closed!... Error: End of file
2017-10-10 18:43:08.538 MySensors: retrying in 30 seconds...

None of them picks up sensor reports

gohan

Do you have a spare microsd and try a clean install ?

miljume

@gohan I have tried a clean install both with Rapbian Stretch and Raspbian Jessie but the results are the same

gohan

Did you check if spi is enabled in configuration? Sorry for stupid questions, but I need to broaden the search for the issue

wergeld

@gohan, I can only speak for me but I have done the following on my RPi 2 B:
Changed out radios
Used shield for radio or just straight wiring to radio
New flash of latest minimal Raspbian
Enabled SPI

And various combinations of those. Maybe something broke in an update to Raspbian or some other change to the mysensors repo?

NRF24L01+ problems in 2.1.1 and 2.2.0 Beta

16

11.7k

11.2k

113.0k