Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

one more nano computer - black swift

axillent Mod 10 Jan 2015, 20:59 last edited by

a new compact computer smaller than raspberry and having wifi on board
http://www.black-swift.com/
Reply Quote 0
1 Reply Last reply 10 Jan 2015, 21:18
Loading More Posts
5
Posts

1.5k
Views
Reply

Reply as topic
Log in to reply
RJ_Make Hero Member 10 Jan 2015, 21:18 last edited by @axillent

@axillent Is it available?
Reply Quote 0
1 Reply Last reply
axillent Mod 10 Jan 2015, 21:40 last edited by

the promise to have first production beginning of the year
will see
Reply Quote 0
1 Reply Last reply
tbowmo Admin 10 Jan 2015, 21:48 last edited by

Hmm only 64MB of ram, and 400Mhz cpu. Seems very small, still it could run a limited Linux system
Reply Quote 0
1 Reply Last reply 11 Jan 2015, 00:09
axillent Mod 11 Jan 2015, 00:09 last edited by @tbowmo

@tbowmo said:

Hmm only 64MB of ram, and 400Mhz cpu. Seems very small, still it could run a limited Linux system

it is designed for openWRT
Reply Quote 0
1 Reply Last reply

5
Posts

1.5k
Views

Log in to reply

1 out of 5

Suggested Topics

Over the air updates
General Discussion • 23 Mar 2014, 21:38 • ToSa 1 Mar 2015, 11:21

87

1
Votes

87
Posts

50.4k
Views

1 Mar 2015, 11:21

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • 24 Jan 2024, 23:06 • wrendral 3 Feb 2024, 07:13

10

0
Votes

10
Posts

42
Views

3 Feb 2024, 07:13

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.
Best time of year to buy higher quality small project solar panels?
Hardware • 10 Jun 2021, 19:19 • NeverDie 30 Aug 2024, 14:01

5

1
Votes

5
Posts

71
Views

30 Aug 2024, 14:01

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
Arduino Nano Every problem
Hardware • 1 Feb 2020, 09:18 • hakha4 5 Dec 2023, 02:21

6

1
Votes

6
Posts

84
Views

5 Dec 2023, 02:21

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • 6 Jan 2024, 19:39 • OldSurferDude 11 Jan 2024, 04:39

2

0
Votes

2
Posts

22
Views

11 Jan 2024, 04:39

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
Newbie questions
Hardware • 14 Feb 2025, 20:03 • magwas 14 Feb 2025, 20:03

1

0
Votes

1
Posts

4
Views

No one has replied

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1