Windows GUI/Controller for MySensors

[Francois]

@tekka the reason I asked I has a problem where I had 2 node with the same node ID and a could not do a OTA via MYSController. As i keep the same ID. I clear the EEPROM and still l it did not work. So the only why I could get the node working was to reflash the boot loader.

[tekka]

@Francois in general, if two nodes have the same ID, you have to disconnect one node and reassign ID/clear eeprom of the other node:

• MYSBootloader 1.1: use the bootloader commands in MYSController (right mouse click on the node, then reassign ID or clear EEPROM)
• MYSBootloader 1.0: upload the clear eeprom sketch and have the controller reassigning the ID

[Francois]

@tekka I doing this and still the node ID is not changing. I change this node to 4 and it still come up as Node 3. The reboot command also don't reboot the device. I have to do a manual reset on the device is this normal?

[tekka]

@Francois ok, I see - can you post or send the log (with debug mode on) to myscontroller at gmail dot com.
If the reboot command is not functioning properly you may have a corrupt routing table: Try clearing the routing table of the node & all routing nodes in between (right mouse click on the node in the routing panel|clear routing table) then try again to reboot.

[Francois]

@tekka will it be a problem if I don't have all my node on the MYSbootloader? Currently I only have 2 of my nodes with MYSBootloader. I am still testing before I change all the nodes

[tekka]

@Francois should be fine

[Francois]

@tekka log file send

[Francois]

@tekka See below it reboot the first time when I try it the seconde time it did
not it just say reboot

Here is my routing Tabel:

[tekka]

@Francois the node has AUTO ID or fix assigned ID (i.e. 91?) - if so, this may be an issue in the dev branch

[rvendrame]

Anyone who owns a Vera controller, and perhaps was able to connect this nice MYSController to the mySensors serial-gateway hooked into Vera USB?

The serial port is exposed in TCP/IP by Vera via ser2net, however I wasn't successful by setting MYSController to <my-vera-ip>:3482 (3482 is the port displayed in Vera -> APPS -> Develop Apps -> Serial port config ) .

(maybe the Vera MYSensor plugin opens the serial connection to GW in 'exclusive' mode or something like that? )

If I remove the GW from Vera USB and plug in my computer, MYSController works fine.

Anyone? Am I wanting too much?

[JoergP]

I'm new to MySensors and playing around with this implementation since some weeks. I implemented an interface from serial to MQTT per python and everything is running fine so far. The last days I spend some time with the bootloader (it is a great feature!!!). I created also a python mqtt client that will take care on that.

I got really crazy the last 2 days with the CRC calculation. I always got a different CRC as as the MYSController. Now I found out, that it seems that the last byte within the HEX file is interpreted as 0xFF instead of the real data. I flashed now one sensor with the MYSController and as I can see in the log-file -> the last byte is read from the HEX as wrong value (0xFF instead of 0x14) -> therefore the HEX file is not flashed correctly (last byte is wrong) -> it seems that this is a bug in MYSController. (I'm using version 0.1.2.278)

Can you check that please?

[tekka]

@JoergP Indeed, bug confirmed. There is an error in the block padding code. I will push the update soon. Thanks for reporting!

[cdr]

Hello,

First of all, thanks Tekka for the great MYScontroller!

I want to get started with the MYSbootloader but I can't get it to work. I've followed each step securely but I never "see" my arduino in MYScontroller after flashing the bootloader. Perhaps I misunderstand the theory behind the bootloader? Maybe the fuses are wrong, I don't know.

Perhaps someone can reply to the following;

• Can I just attach a radio module to an Arduino Nano as instructed on the site, clear the eeprom and then burn the bootloader using usbasp? (as instructed in this thread) Or do I need to upload the gateway sketch before burning the bootloader?
• I have a hard time understanding what the bootloader does, I think it enables low level nrf functionality for OTA and Myscontroller instructions like reboot and clear eeprom etc. But when I upload a sketch does that mean the bootloader inits the nrf first and then the uploaded sketch will just re-init the nrf again?
• Is there a way to debug the bootloader?

Have a good laugh if you will at these noob questions, but any help is appreciated :)

[tekka]

@cdr said:

• Can I just attach a radio module to an Arduino Nano as instructed on the site, clear the eeprom and then burn the bootloader using usbasp? (as instructed in this thread) Or do I need to upload the gateway sketch before burning the bootloader?

Yes, simply attach the radio and burn the bootloader with the correct fuse settings (see the fuses.txt file in the bootloader directory). If you intend to use MYSController, set AutoID to automatically assign IDs to the nodes.

• I have a hard time understanding what the bootloader does, I think it enables low level nrf functionality for OTA and Myscontroller instructions like reboot and clear eeprom etc. But when I upload a sketch does that mean the bootloader inits the nrf first and then the uploaded sketch will just re-init the nrf again?

Yes, that's correct. The bootloader is a small piece of code located at the end of the flash area that is (if the fuses are set accordingly) executed first upon rebooting and allows for low-level OTA updates.

• Is there a way to debug the bootloader?

Yes, there are several ways (e.g. visual with LED, serial output, or AVR DebugWire)...you may want to google these topics for further information..

Have a good laugh if you will at these noob questions, but any help is appreciated :)

no problem :)

[cdr]

Hi tekka,

Thanks for the response and clarification. I think I need more knowledge about fuses and bootloaders, it could be that the arduino clones are giving me sh&t.

Looking forward to my success and MYSloader 2.0 ofcourse!

Thanks again for all your work.

[tekka]

MYSController Version 0.1.2.280 released

Changelog:

• Bugfix FW padding (thanks @JoergP)
• Handler rework
• Logging format rework
• Support battery-powered/sleeping nodes
• Refactoring

Update via update button in MYSController or download here.

[Mickey]

This is the most helpful tool I used since I started messing around with mysensors.

I hate to nag but this tool source code would be a giant step to someone looking to create a new controller by himself.
.

[robosensor]

Hello, how to verify right bootloader is uploaded to arduino?

I'm using two Arduino Pro Mini 328 5.0V 16Mhz, one as ArduinoISP programmer and one as sensor node to upload bootloader and firmware.

I followed manual (http://forum.mysensors.org/topic/838/windows-gui-controller-for-mysensors/76) step by step.

I have tried MYSBootloader.hex coming from latest MYSController 0.1.2.280 and MYSBootloader.hex (1.1) from github with same results.

Upload log is here:

C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM10 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x06:m -Uhfuse:w:0xDA:m -Ulfuse:w:0xF7:m 

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM10
         Using Programmer              : stk500v1
         Overriding Baud Rate          : 19200
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : STK500
         Description     : Atmel STK500 Version 1.x firmware
         Hardware Version: 2
         Firmware Version: 1.18
         Topcard         : Unknown
         Vtarget         : 0.0 V
         Varef           : 0.0 V
         Oscillator      : Off
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.05s

avrdude: Device signature = 0x1e950f
avrdude: erasing chip
avrdude: reading input file "0x3F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x3F:
avrdude: load data lock data from input file 0x3F:
avrdude: input file 0x3F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.02s

avrdude: verifying ...
avrdude: 1 bytes of lock verified
avrdude: reading input file "0x06"
avrdude: writing efuse (1 bytes):

Writing | ################################################## | 100% 0.02s

avrdude: 1 bytes of efuse written
avrdude: verifying efuse memory against 0x06:
avrdude: load data efuse data from input file 0x06:
avrdude: input file 0x06 contains 1 bytes
avrdude: reading on-chip efuse data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: 1 bytes of efuse verified
avrdude: reading input file "0xDA"
avrdude: writing hfuse (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of hfuse written
avrdude: verifying hfuse memory against 0xDA:
avrdude: load data hfuse data from input file 0xDA:
avrdude: input file 0xDA contains 1 bytes
avrdude: reading on-chip hfuse data:

Reading | ################################################## | 100% 0.02s

avrdude: verifying ...
avrdude: 1 bytes of hfuse verified
avrdude: reading input file "0xF7"
avrdude: writing lfuse (1 bytes):

C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM10 -b19200 -Uflash:w:C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/MySensors/MYSBootloader.hex:i -Ulock:w:0x0F:m 

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Writing | ################################################## | 100% 0.02s

avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xF7:
avrdude: load data lfuse data from input file 0xF7:
avrdude: input file 0xF7 contains 1 bytes
avrdude: reading on-chip lfuse data:

Reading | ################################################## | 100% 0.02s

avrdude: verifying ...
avrdude: 1 bytes of lfuse verified

avrdude done.  Thank you.

Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM10
         Using Programmer              : stk500v1
         Overriding Baud Rate          : 19200
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : STK500
         Description     : Atmel STK500 Version 1.x firmware
         Hardware Version: 2
         Firmware Version: 1.18
         Topcard         : Unknown
         Vtarget         : 0.0 V
         Varef           : 0.0 V
         Oscillator      : Off
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.06s

avrdude: Device signature = 0x1e950f
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/MySensors/MYSBootloader.hex"
avrdude: writing flash (32722 bytes):

Writing | ################################################## | 100% -0.00s

avrdude: 32722 bytes of flash written
avrdude: verifying flash memory against C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/MySensors/MYSBootloader.hex:
avrdude: load data flash data from input file C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/MySensors/MYSBootloader.hex:
avrdude: input file C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/MySensors/MYSBootloader.hex contains 32722 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.02s

avrdude: verifying ...
avrdude: 32722 bytes of flash verified
avrdude: reading input file "0x0F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.05s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x0F:
avrdude: load data lock data from input file 0x0F:
avrdude: input file 0x0F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: 1 bytes of lock verified

avrdude done.  Thank you.

Fuses looks like right:

avrdude: Device signature = 0x1e950f
avrdude: safemode: lfuse reads as F7
avrdude: safemode: hfuse reads as DA
avrdude: safemode: efuse reads as 6

MYSController log after node with new bootloader start:

14.06.2015 10:14:46	STARTUP	Initialize message logging
14.06.2015 10:14:46	STARTUP	MYSController 0.1.2.280
14.06.2015 10:14:46	STARTUP	FPC 2.6.4 / Lazarus 1.4
14.06.2015 10:14:46	STARTUP	still under development :) tekka 2015
14.06.2015 10:14:46	STARTUP	Load INI file...
14.06.2015 10:14:46	STARTUP	INI version 0.1.2.280
14.06.2015 10:14:46	INFO	*** Logging START ***
14.06.2015 10:14:46	VERSION	MYSController 0.1.2.280
14.06.2015 10:14:46	STARTUP	INI file loaded
14.06.2015 10:14:46	STARTUP	Loading FW repository...
14.06.2015 10:14:46	REPO	FW "Blink" loaded. t=10, v=1, blocks=72, crc=0xD098
14.06.2015 10:14:46	REPO	FW "TimeReporter" loaded. t=20, v=1, blocks=840, crc=0x4AC5
14.06.2015 10:14:46	REPO	FW repository loaded. Items=2
14.06.2015 10:14:46	STARTUP	Initialize message types
14.06.2015 10:14:46	NODE	New node discovered, node id=0
14.06.2015 10:14:46	NODE	New node discovered, node id=255
14.06.2015 10:14:49	INFO	Connected to 192.168.0.1:12345
14.06.2015 10:14:59	UPDATE	4295098648
14.06.2015 10:21:26	CHILD	New child discovered, node id=0, child id=0
14.06.2015 10:21:26	RX	0;0;3;0;9;read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
14.06.2015 10:21:26	RX	0;0;3;0;9;send: 0-0-255-255 s=255,c=3,t=8,pt=1,l=1,sg=0,st=bc:0
14.06.2015 10:21:28	RX	0;0;3;0;9;read: 3-3-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
14.06.2015 10:21:28	RX	0;0;3;0;9;send: 0-0-3-3 s=255,c=3,t=8,pt=1,l=1,sg=0,st=ok:0
14.06.2015 10:21:30	RX	0;0;3;0;9;read: 3-3-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
14.06.2015 10:21:30	NODE	New node discovered, node id=3
14.06.2015 10:21:30	CHILD	New child discovered, node id=3, child id=internal
14.06.2015 10:21:30	TX	3;255;3;0;6;M
14.06.2015 10:21:30	RX	3;255;3;0;6;0
14.06.2015 10:21:30	RX	0;0;3;0;9;send: 0-0-3-3 s=255,c=3,t=6,pt=0,l=1,sg=0,st=ok:M
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=255,c=3,t=11,pt=0,l=7,sg=0:Balcony
14.06.2015 10:21:32	RX	3;255;3;0;11;Balcony
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
14.06.2015 10:21:32	RX	3;255;3;0;12;1.0
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=1,c=0,t=16,pt=0,l=20,sg=0:Photoconductive Cel
14.06.2015 10:21:32	CHILD	New child discovered, node id=3, child id=1
14.06.2015 10:21:32	DEBUG	Update child id=1, type=LIGHT_LEVEL
14.06.2015 10:21:32	RX	3;1;0;0;16;Photoconductive Cell
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=2,c=0,t=6,pt=0,l=3,sg=0:ds0
14.06.2015 10:21:32	CHILD	New child discovered, node id=3, child id=2
14.06.2015 10:21:32	DEBUG	Update child id=2, type=TEMP
14.06.2015 10:21:32	RX	3;2;0;0;6;ds0
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=3,c=0,t=6,pt=0,l=3,sg=0:ds1
14.06.2015 10:21:32	CHILD	New child discovered, node id=3, child id=3
14.06.2015 10:21:32	DEBUG	Update child id=3, type=TEMP
14.06.2015 10:21:32	RX	3;3;0;0;6;ds1
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=4,c=0,t=6,pt=0,l=3,sg=0:ds2
14.06.2015 10:21:32	CHILD	New child discovered, node id=3, child id=4
14.06.2015 10:21:32	DEBUG	Update child id=4, type=TEMP
14.06.2015 10:21:32	RX	3;4;0;0;6;ds2
14.06.2015 10:21:32	RX	0;0;3;0;9;read: 3-3-0 s=5,c=0,t=6,pt=0,l=3,sg=0:ds3
14.06.2015 10:21:32	CHILD	New child discovered, node id=3, child id=5
14.06.2015 10:21:32	DEBUG	Update child id=5, type=TEMP
14.06.2015 10:21:32	RX	3;5;0;0;6;ds3
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=6,c=0,t=6,pt=0,l=3,sg=0:ds4
14.06.2015 10:21:33	CHILD	New child discovered, node id=3, child id=6
14.06.2015 10:21:33	DEBUG	Update child id=6, type=TEMP
14.06.2015 10:21:33	RX	3;6;0;0;6;ds4
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=7,c=0,t=6,pt=0,l=3,sg=0:ds5
14.06.2015 10:21:33	CHILD	New child discovered, node id=3, child id=7
14.06.2015 10:21:33	DEBUG	Update child id=7, type=TEMP
14.06.2015 10:21:33	RX	3;7;0;0;6;ds5
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=8,c=0,t=6,pt=0,l=3,sg=0:ds6
14.06.2015 10:21:33	CHILD	New child discovered, node id=3, child id=8
14.06.2015 10:21:33	DEBUG	Update child id=8, type=TEMP
14.06.2015 10:21:33	RX	3;8;0;0;6;ds6
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=9,c=0,t=6,pt=0,l=3,sg=0:ds7
14.06.2015 10:21:33	CHILD	New child discovered, node id=3, child id=9
14.06.2015 10:21:33	DEBUG	Update child id=9, type=TEMP
14.06.2015 10:21:33	RX	3;9;0;0;6;ds7
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=10,c=0,t=6,pt=0,l=3,sg=0:ds8
14.06.2015 10:21:33	CHILD	New child discovered, node id=3, child id=10
14.06.2015 10:21:33	DEBUG	Update child id=10, type=TEMP
14.06.2015 10:21:33	RX	3;10;0;0;6;ds8
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=11,c=0,t=6,pt=0,l=3,sg=0:ds9
14.06.2015 10:21:33	CHILD	New child discovered, node id=3, child id=11
14.06.2015 10:21:33	DEBUG	Update child id=11, type=TEMP
14.06.2015 10:21:33	RX	3;11;0;0;6;ds9
14.06.2015 10:21:33	RX	0;0;3;0;9;read: 3-3-0 s=1,c=1,t=23,pt=2,l=2,sg=0:49
14.06.2015 10:21:33	RX	3;1;1;0;23;49
14.06.2015 10:21:36	RX	0;0;3;0;9;read: 3-3-0 s=3,c=1,t=0,pt=7,l=5,sg=0:26.5625
14.06.2015 10:21:36	RX	3;3;1;0;0;26.5625
14.06.2015 10:21:37	RX	0;0;3;0;9;read: 3-3-0 s=1,c=1,t=23,pt=2,l=2,sg=0:49
14.06.2015 10:21:37	RX	3;1;1;0;23;49

Node successfully start and connecting to gateway with new bootloader, but then I issue reboot command in MYSController, node hangs up completely, even reset button isn't working. Only power off, then power on helps. Assign firmware isn't working also (nothing happens).

[tekka]

@robosensor said:

The MYSBootloader.hex file you are flashing has a wrong file size (=32722 bytes) in your post:

avrdude: reading input file "C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/MySensors/MYSBootloader.hex"
avrdude: writing flash (32722 bytes):

MYSBootloader 1.1 should have ~2kb

From your log I assume, that you flashed the sketch instead of the bootloader.

Please pay attention to steps 3 and 13 from the step-by-step manual.

[robosensor]

@tekka I have noticed this, but I thought that this is due to the peculiarities of bootloader upload process (upper end of memory).

 Directory of C:\Program Files (x86)\Arduino\hardware\arduino\avr\bootloaders\MySensors

14.06.2015  00:08    <DIR>          .
14.06.2015  00:08    <DIR>          ..
14.06.2015  09:59             5 548 MYSBootloader.hex
               1 File(s)          5 548 bytes

For sketch size is too big (32722 bytes), real sketch size is 19928 bytes.

In any case, thanks for the help, I'll try to figure it out or try to download it manually using avrdude.