BananaPi M1 gateway wont work



  • Hi,
    I am newbie in My sensors and have problem with BananaPi M1 Soc=A20.
    When i try to configure MySensors Gateway always after compilation i receive that:

    root@bananapi:/home/pi/install/MySensors# ./bin/mysgw -d
    mysgw: Starting gateway...
    mysgw: Protocol version - 2.2.0-rc.2
    mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-rc.2
    mysgw: TSF:LRT:OK
    mysgw: TSM:INIT
    mysgw: TSF:WUR:MS=0
    mysgw: !TSM:INIT:TSP FAIL
    mysgw: TSM:FAIL:CNT=1
    mysgw: TSM:FAIL:DIS
    mysgw: TSF:TDI:TSL
    

    Compilation always OK without any errors.
    Hardware is connected like need to be and connection work on RaspberryPi 2 (same GPIO pinout).
    I try with many difference settings in compilation but without sucsses.
    With gpio readall i see all GPIOs and can comand it .

    root@bananapi:/home/pi/install/MySensors# gpio readall
    +----------+-Rev3-+------+--------+------+-------+
    | wiringPi | GPIO | Phys | Name   | Mode | Value |
    +----------+------+------+--------+------+-------+
    |      0   |  17  |  11  | GPIO 0 | OUT  | High  |
    |      1   |  18  |  12  | GPIO 1 | IN   | Low   |
    |      2   |  27  |  13  | GPIO 2 | ALT4 | Low   |
    |      3   |  22  |  15  | GPIO 3 | IN   | Low   |
    |      4   |  23  |  16  | GPIO 4 | OUT  | High  |
    |      5   |  24  |  18  | GPIO 5 | IN   | Low   |
    |      6   |  25  |  22  | GPIO 6 | IN   | Low   |
    |      7   |   4  |   7  | GPIO 7 | IN   | Low   |
    |      8   |   2  |   3  | SDA    | ALT5 | Low   |
    |      9   |   3  |   5  | SCL    | ALT5 | Low   |
    |     10   |   8  |  24  | CE0    | IN   | Low   |
    |     11   |   7  |  26  | CE1    | ALT5 | Low   |
    |     12   |  10  |  19  | MOSI   | IN   | Low   |
    |     13   |   9  |  21  | MISO   | IN   | Low   |
    |     14   |  11  |  23  | SCLK   | ALT5 | Low   |
    |     15   |  14  |   8  | TxD    | OUT  | High  |
    |     16   |  15  |  10  | RxD    | OUT  | High  |
    |     17   |  28  |   3  | GPIO 8 | ALT0 | Low   |
    |     18   |  29  |   4  | GPIO 9 | IN   | Low   |
    |     19   |  30  |   5  | GPIO10 | IN   | Low   |
    |     20   |  31  |   6  | GPIO11 | ALT4 | Low   |
    +----------+------+------+--------+------+-------+
    

    This is some of my configures:

     ./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=8 --my-rf24-cs-pin=25 --my-gateway=ethernet --my-port=5003
    
    ./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=24 --my-rf24-cs-pin=22 --my-gateway=ethernet --my-port=5003
    
    ./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=10--my-rf24-cs-pin=6 --my-gateway=ethernet --my-port=5003
    

    This is my answer on list devices

    root@bananapi:/home/pi/install/MySensors# ls /dev/spi*
    /dev/spidev0.0  /dev/spidev0.1
    

    Everything need to be ok but is not 😞 .
    Because thi is not a my 1st project i know all work on RaspberryPi 2 and Orange Pi PC - Soc=H3.
    I have a problem with Soc= A20.

    Please help

    Kind Regards



  • @kebibg hello
    Was you able to bring it to work?

    Thanks, Simon


 

346
Online

7.9k
Users

8.7k
Topics

93.6k
Posts