Navigation

    • Register
    • Login
    • OpenHardware.io
    • Categories
    • Recent
    • Tags
    • Popular
    1. Home
    2. mlg
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    mlg

    @mlg

    0
    Reputation
    20
    Posts
    531
    Profile views
    0
    Followers
    1
    Following
    Joined Last Online

    mlg Follow

    Best posts made by mlg

    This user hasn't posted anything yet.

    Latest posts made by mlg

    • RE: Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch

      Update

      Finally after changing reed switch all works !

      However , sometimes mysensors gateway stop responding (few weeks works fine), I try to ping Ip of the gateway and no have any reply, solution is power off gateway .

      It is possible to place the gateway (mysensors) to ping a network address and if it does not answer automatically make a restart and wait/limit to a restart every 20 minutes? (to prevent the restart loop)

      posted in Vera
      mlg
      mlg
    • RE: Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch

      @hek

      Working!!!! Tks

      I only have one more problem, with simple button switch ( like that ) simulate door open/close , I receive message "Door value:0 and 1" and status in vera changed, but with reed switch ( like that ) door status no change with magnetic , I bought 5 reed switch and any works 😞

      Reed switch problem right ?

      posted in Vera
      mlg
      mlg
    • RE: Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch

      @hek

      Still not working 😕

      void loop() 
      {  
         wait(200);
          // Read digital motion value
        boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
      
          if (lastTripped != tripped ) {
            send(msg.set(tripped?"1":"0")); // Send new state and request ack back
            Serial.println(tripped);
            lastTripped=tripped; 
      }
      debouncer.update();
        int value = debouncer.read();
        if (value != oldValue) {
           Serial.print("Door value: ");
           Serial.println(value);
           send(msgdoor.set(value==HIGH ? 1 : 0));
           oldValue = value;
      
        }
      }
      
      posted in Vera
      mlg
      mlg
    • RE: Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch

      Any ideia plz?

      posted in Vera
      mlg
      mlg
    • RE: Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch

      @hek tks, motion sensor now appear but magnetic switch no 😞 need resistor ?

      Update code

      
      // Enable debug prints to serial monitor
      #define MY_DEBUG 
      
      // Enable gateway ethernet module type 
      #define MY_GATEWAY_W5100
      
      #define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
      
      // The port to keep open on node server mode / or port to contact in client mode
      #define MY_PORT 5003        
       
      // The MAC address can be anything you want but should be unique on your network.
      // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
      // Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
       #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
      
      // Enable inclusion mode
       #define MY_INCLUSION_MODE_FEATURE
      // Enable Inclusion mode button on gateway
      // #define MY_INCLUSION_BUTTON_FEATURE
      // Set inclusion mode duration (in seconds)
       #define MY_INCLUSION_MODE_DURATION 60 
      // Digital pin used for inclusion mode button
      // #define MY_INCLUSION_MODE_BUTTON_PIN  4 
      
      #include <SPI.h>
      #include <Ethernet.h>
      #include <MySensor.h>
      #include <Bounce2.h>
      
      #define RELAY_1  5  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
      #define NUMBER_OF_RELAYS 4 // Total number of attached relays
      #define RELAY_ON 1  // GPIO value to write to turn on attached relay
      #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
      #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
      #define CHILD_ID 69   // Id of the sensor child
      #define ID 70
      #define OPEN 1
      #define CLOSE 0
      #define BUTTON_PIN  4  // Arduino Digital I/O pin for button/reed switc
      
      boolean lastTripped = 0;
      Bounce debouncer = Bounce(); 
      int oldValue=-1;
      
      // Initialize motion message
      MyMessage msg(CHILD_ID, V_TRIPPED);
      MyMessage msgdoor(ID,V_TRIPPED);
      
      
      void before() { 
        for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
          // Then set relay pins in output mode
          pinMode(pin, OUTPUT);   
          // Set relay to last known state (using eeprom storage) 
          digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
        }
      }
      
      void setup() {
        pinMode(BUTTON_PIN,INPUT_PULLUP);
        debouncer.attach(BUTTON_PIN);
        debouncer.interval(5);
        present(ID, S_DOOR); // S_DOOR
        
      }
      
      void presentation()  
      {   
        // Send the sketch version information to the gateway and Controller
        sendSketchInfo("Relay", "1.0");
      
        for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
          // Register all sensors to gw (they will be created as child devices)
          present(sensor, S_LIGHT);
        }
           pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
        // Register all sensors to gw (they will be created as child devices)
        present(CHILD_ID, S_MOTION);
      }
      
      
      void loop() 
      {
          // Read digital motion value
        boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
      
          if (lastTripped != tripped ) {
            send(msg.set(tripped?"1":"0")); // Send new state and request ack back
            Serial.println(tripped);
            lastTripped=tripped; 
      }
      debouncer.update();
        int value = debouncer.read();
        if (value != oldValue) {
           Serial.print("Door value: ");
           Serial.println(value);
           send(msgdoor.set(value==HIGH ? 1 : 0));
           oldValue = value;
      
        }
      }
      
      void receive(const MyMessage &message) {
        // We only expect one type of message from controller. But we better check anyway.
        if (message.type==V_LIGHT) {
           // Change relay state
           digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
           // Store state in eeprom
           saveState(message.sensor, message.getBool());
           // Write some debug info
           Serial.print("Incoming change for sensor:");
           Serial.print(message.sensor);
           Serial.print(", New status: ");
           Serial.println(message.getBool());
         } 
      }```
      posted in Vera
      mlg
      mlg
    • Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch

      Hello ,

      I'm trying to build the gateway with all attached sensors

      But when I inclusion, only appears the 4 relays in Vera , what is wrong with the code?

      not appear --> motion and Magnetic Switch

      Setup:
      Arduino Uno R3
      W5100 Shield
      4 Relay - pin 5,6,7,8
      1 motion - pin 3
      1 magnetic switch - pin 4

      // Enable debug prints to serial monitor
      #define MY_DEBUG 
      
      // Enable gateway ethernet module type 
      #define MY_GATEWAY_W5100
      
      #define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
      
      // The port to keep open on node server mode / or port to contact in client mode
      #define MY_PORT 5003        
       
      // The MAC address can be anything you want but should be unique on your network.
      // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
      // Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
       #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
      
      // Enable inclusion mode
       #define MY_INCLUSION_MODE_FEATURE
      // Enable Inclusion mode button on gateway
      // #define MY_INCLUSION_BUTTON_FEATURE
      // Set inclusion mode duration (in seconds)
       #define MY_INCLUSION_MODE_DURATION 60 
      // Digital pin used for inclusion mode button
      // #define MY_INCLUSION_MODE_BUTTON_PIN  4 
      
      #include <SPI.h>
      #include <Ethernet.h>
      #include <MySensor.h>
      #include <Bounce2.h>
      
      #define RELAY_1  5  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
      #define NUMBER_OF_RELAYS 4 // Total number of attached relays
      #define RELAY_ON 1  // GPIO value to write to turn on attached relay
      #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
      #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
      #define CHILD_ID 3   // Id of the sensor child
      #define ID 4
      
      #define OPEN 1
      #define CLOSE 0
      #define BUTTON_PIN  4  // Arduino Digital I/O pin for button/reed switc
      
      boolean lastTripped = 0;
      Bounce debouncer = Bounce(); 
      int oldValue=-1;
      
      // Initialize motion message
      MyMessage msg(CHILD_ID, V_TRIPPED);
      MyMessage msgdoor(ID,V_TRIPPED);
      
      
      void before() { 
        for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
          // Then set relay pins in output mode
          pinMode(pin, OUTPUT);   
          // Set relay to last known state (using eeprom storage) 
          digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
        }
      }
      
      void setup() {
        pinMode(BUTTON_PIN,INPUT_PULLUP);
        debouncer.attach(BUTTON_PIN);
        debouncer.interval(5);
        present(ID, S_LIGHT); // S_DOOR
        
      }
      
      void presentation()  
      {   
        // Send the sketch version information to the gateway and Controller
        sendSketchInfo("Relay", "1.0");
      
        for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
          // Register all sensors to gw (they will be created as child devices)
          present(sensor, S_LIGHT);
        }
           pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
        // Register all sensors to gw (they will be created as child devices)
        present(CHILD_ID, S_MOTION);
      }
      
      
      void loop() 
      {
          // Read digital motion value
        boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
      
          if (lastTripped != tripped ) {
            send(msg.set(tripped?"1":"0")); // Send new state and request ack back
            Serial.println(tripped);
            lastTripped=tripped; 
      }
      debouncer.update();
        int value = debouncer.read();
        if (value != oldValue) {
           Serial.print("Door value: ");
           Serial.println(value);
           send(msgdoor.set(value==HIGH ? 1 : 0));
           oldValue = value;
      
        }
      }
      
      void receive(const MyMessage &message) {
        // We only expect one type of message from controller. But we better check anyway.
        if (message.type==V_LIGHT) {
           // Change relay state
           digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
           // Store state in eeprom
           saveState(message.sensor, message.getBool());
           // Write some debug info
           Serial.print("Incoming change for sensor:");
           Serial.print(message.sensor);
           Serial.print(", New status: ");
           Serial.println(message.getBool());
         } 
      }```
      posted in Vera
      mlg
      mlg
    • RE: Ethernet Gateway without NRF24L01+

      @hek

      I found one solution,I turn on sensor in ethernet gateway and press start inclusion and reload engine in Vera .In this way automatically add the sensor

      However compiled another code by adding a relay but is not added is something wrong?
      it is necessary void before, presentation ? and assign a child ID to RELAY ?

      /**
       * The MySensors Arduino library handles the wireless radio link and protocol
       * between your home built sensors/actuators and HA controller of choice.
       * The sensors forms a self healing radio network with optional repeaters. Each
       * repeater and gateway builds a routing tables in EEPROM which keeps track of the
       * network topology allowing messages to be routed to nodes.
       *
       * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
       * Copyright (C) 2013-2015 Sensnology AB
       * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
       *
       * Documentation: http://www.mysensors.org
       * Support Forum: http://forum.mysensors.org
       *
       * This program is free software; you can redistribute it and/or
       * modify it under the terms of the GNU General Public License
       * version 2 as published by the Free Software Foundation.
       *
       *******************************
       *
       * REVISION HISTORY
       * Version 1.0 - Henrik EKblad
       * Contribution by a-lurker and Anticimex,
       * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
       * Contribution by Tomas Hozza <thozza@gmail.com>
       *
       *
       * DESCRIPTION
       * The EthernetGateway sends data received from sensors to the ethernet link.
       * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
       *
       * The GW code is designed for Arduino 328p / 16MHz.  ATmega168 does not have enough memory to run this program.
       *
       * LED purposes:
       * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
       * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
       * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
       * - ERR (red) - fast blink on error during transmission error or recieve crc error
       *
       * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
       *
       */
      
      // Enable debug prints to serial monitor
      #define MY_DEBUG 
      
      // Enable gateway ethernet module type 
      #define MY_GATEWAY_W5100
      
      #define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
      // Renewal period if using DHCP
      //#define MY_IP_RENEWAL_INTERVAL 60000
      // The port to keep open on node server mode / or port to contact in client mode
      #define MY_PORT 5003        
       
      // The MAC address can be anything you want but should be unique on your network.
      // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
      // Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
       #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
      
      // Flash leds on rx/tx/err
      // #define MY_LEDS_BLINKING_FEATURE
      // Set blinking period
      // #define MY_DEFAULT_LED_BLINK_PERIOD 300
      
      // Enable inclusion mode
       #define MY_INCLUSION_MODE_FEATURE
      // Enable Inclusion mode button on gateway
      // #define MY_INCLUSION_BUTTON_FEATURE
      // Set inclusion mode duration (in seconds)
       #define MY_INCLUSION_MODE_DURATION 60 
      // Digital pin used for inclusion mode button
      // #define MY_INCLUSION_MODE_BUTTON_PIN  4 
      
      #include <SPI.h>
      #include <Ethernet.h>
      #include <MySensor.h>
      
      
      #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
      #define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
      #define CHILD_ID 1   // Id of the sensor child
      boolean lastTripped = 0;
      
      #define RELAY_1  2  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
      #define NUMBER_OF_RELAYS 1 // Total number of attached relays
      #define RELAY_ON 1  // GPIO value to write to turn on attached relay
      #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
      
      
      // Initialize motion message
      MyMessage msg(CHILD_ID, V_TRIPPED);
      
      void setup()  
      {  
         
        // Send the sketch version information to the gateway and Controller
          sendSketchInfo("Motion Relay", "1.0");
       
          pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
        // Register all sensors to gw (they will be created as child devices)
          present(CHILD_ID, S_MOTION);
      
          for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
          present(sensor, S_LIGHT);
        // Then set relay pins in output mode
          pinMode(pin, OUTPUT);   
        // Set relay to last known state (using eeprom storage) 
          digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
        }
      }
      
      
      void loop()     
      {     
        
        // Read digital motion value
        boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
      
          if (lastTripped != tripped ) {
            send(msg.set(tripped?"1":"0")); // Send new state and request ack back
            Serial.println(tripped);
            lastTripped=tripped;
      }
      }
      
      void incomingMessage(const MyMessage &message) {
        // We only expect one type of message from controller. But we better check anyway.
        if (message.type==V_LIGHT) {
           // Change relay state
           digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
           // Store state in eeprom
           saveState(message.sensor, message.getBool());
           // Write some debug info
           Serial.print("Incoming change for sensor:");
           Serial.print(message.sensor);
           Serial.print(", New status: ");
           Serial.println(message.getBool());
         } 
      }
      
      posted in Vera
      mlg
      mlg
    • RE: Ethernet Gateway without NRF24L01+

      @hek

      It's normal? If I disconnect the cables get 1/0/1/0 and not stopped

      posted in Vera
      mlg
      mlg
    • RE: Ethernet Gateway without NRF24L01+

      @hek

      How I make sensor node reset ? Disconnected all cables ? digital pin 3 + gnd + 5v ?

      If I disconect all cables I log that

      0;255;3;0;9;Starting gateway (R-NGA-, 2.0.0-beta)
      IP: 192.168.1.169
      0;255;3;0;9;Init complete, id=0, parent=0, distance=0
      0;255;3;0;9;Eth: connect
      0;255;3;0;9;Eth: 0;0;3;0;5;1
      0;255;3;0;9;Eth: 
      1
      0
      1
      0
      1
      0
      1
      0
      1
      0
      1
      0
      1
      0
      1
      0
      
      posted in Vera
      mlg
      mlg
    • RE: Ethernet Gateway without NRF24L01+

      Any Ideia?

      posted in Vera
      mlg
      mlg