@mfalkvidd worked thanks a lot!

@mfalkvidd worked thanks a lot!

Hello,
right know I'm trying to get my Wemos D1 mini configured as Wifi Gateway for pimatic.
I've used this instruction.
https://www.mysensors.org/build/esp8266_gateway
But i get stucked at the verfiy compile step.

I get the following Error during compilation and don't know how to get rid of it:

 error: previous declaration 'void ets_update_cpu_frequency(uint32_t)' here
 void ets_update_cpu_frequency(uint32_t ticks_per_us);
      ^
exit status 1
Fehler beim Kompilieren für das Board LOLIN(WEMOS) D1 R2 & mini.

I've tried the blink example and i also flashed (external) EasyESP.
So the Hardware it self is OK and working.
I know the issue disappears when the MySensors.h get commented out.

Did someone know how to proceed?

Thanks
Free

Thanks for the answer. I tried this and it didn't work. I've started a thread in pimatic forum as well. Maybe they know how to do this.
Thanks

Ok great,
that's what I've done.
But which Node and Child ID is needed for this. So that the Input will communicate as a "Sensor" to the gateway.

Because the Pimatic plugin need to know where to look.

// Enable debug prints to serial monitor
#define MY_DEBUG
// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 115200
#endif

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>
#define ArrayLenth 10
#define PH_SENSOR_ANALOG_PIN A0
unsigned long lastSend = 0;
static const unsigned long SEND_FREQUENCY = 5000;

float lastPhValue;
static const float deltaPhValue = 0.5;

#define MY_NODE_ID 10
#define CHILD_ID_PH_LOCAL 1

MyMessage msg(0, V_PH);
void setup()
{
	// Setup locally attached sensors
}

double analogReadAverage(uint8_t pin, unsigned long ms)
{
    ...
	
    return average;
}

float getPH()
{
		...
        
    if (sendTime || abs(PhValue - lastPhValue) > deltaPhValue)
    {
        Serial.print("pH:");
        Serial.print(PhValue, 2);
       // Serial.println(" ");
               
        lastPhValue = PhValue;
        
        //send(msg.set(PhValue, 1));
        send(msg.set(PhValue, 51));
       
    }
  return lastPhValue;
}


void presentation()
{
	sendSketchInfo("PH Local","1.1");
  present(CHILD_ID_PH_LOCAL,S_WATER_QUALITY); 
}

void loop()
{

  float ph = getPH();
  
	// Send locally attached sensor data here
}

Here the working Pimatic config for a Sensor through a gateway.

      "plugin": "mysensors",
      "driver": "serialport",
      "protocols": "1.5.1",
      "startingNodeId": 1,
      "driverOptions": {
        "//": "'/dev/ttyUSB0' if using serial Gateway",
        "serialDevice": "/dev/ttyUSB1",
        "baudrate": 115200
      }```

```{
      "id": "phmeter",
      "name": "pHmeter",
      "class": "MySensorsPH",
      "nodeid": 9,
      "sensorid": 0,
      "xAttributeOptions": []
    }```


 Thanks

Hello all,
just a question.
Is it possible to add a Sensor (Analog In) directly to a Gateway (arduino) and comunicate this value over USB?

What I want to do is the following:
I've one Sensor which communicate over the Gateway to my Pimatic (over serial USB)
Now I want to add a second Sensor, which is physicaly very close to the Gateway.
So i want to add it there, and it should communicate to Pimatic as well.
Kind of an internal "Sensor" device.

So is this possible? If yes how?

Thanks
Free