I added the capacitor, but there's always the same problem

@hek really? Have you read all? How can adding a capacitor write things on the serial instead of terminal output?

Hi, I have some troubles with PiGatewaySerial (last version from github), raspberry pi Model B Revision 2.0 (000e)

$ cat /proc/cpuinfo
processor	: 0
model name	: ARMv6-compatible processor rev 7 (v6l)
BogoMIPS	: 2.00
Features	: half thumb fastmult vfp edsp java tls 
CPU implementer	: 0x41
CPU architecture: 7
CPU variant	: 0x0
CPU part	: 0xb76
CPU revision	: 7

Hardware	: BCM2708
Revision	: 000e
Serial		: 00000000b9b39005

When i execute ./PiGatewaySerial, it prints on the screen values read from sensors, but
it doesn't write anything on the virtual serial device /dev/ttyMySensorsGateway

$ sudo ./PiGatewaySerial
Starting PiGatewaySerial...
Protocol version - 1.4
Created PTY '/dev/pts/0'
Gateway tty: /dev/ttyMySensorsGateway
================ SPI Configuration ================
CSN Pin   = CE0 (PI Hardware Driven)
CE Pin   = Custom GPIO25
Clock Speed = 8 Mhz
================ NRF Configuration ================
STATUS = 0x0e RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=7 TX_FULL=0
RX_ADDR_P0-1 = 0xa8a8e1fc01 0xa8a8e1fc00
RX_ADDR_P2-5 = 0xff 0xc4 0xc5 0xc6
TX_ADDR = 0xa8a8e1fc01
RX_PW_P0-6 = 0x20 0x20 0x20 0x00 0x00 0x00
EN_AA = 0x3b
EN_RXADDR = 0x06
RF_CH = 0x4c
RF_SETUP = 0x23
CONFIG = 0x0e
DYNPD/FEATURE = 0x3f 0x06
Data Rate = 250KBPS
Model = nRF24L01+
CRC Length = 16 bits
PA Power = PA_LOW
read: 255-255-0 s=255,c=3,t=3,pt=0,l=0:
send: 255-194-1-0 s=255,c=3,t=3,pt=0,l=0,st=fail:
read: 255-0-8 s=255,c=3,t=3,pt=0,l=0:
send: 255-194-1-8 s=255,c=3,t=3,pt=0,l=0,st=fail:

instead, if i read from /dev/ttyMySensorsGateway i obtain only the first
message by the gateway, nothing else.

$ sudo cat /dev/ttyMySensorsGateway
0;0;3;0;14;Gateway startup complete.

$ ls -al /dev/ttyMySensorsGateway 
lrwxrwxrwx 1 root root 10 nov  5 16:32 /dev/ttyMySensorsGateway -> /dev/pts/0

$ ls -al /dev/pts/*
crw-rw---- 1 root tty  136, 0 nov  5 16:32 /dev/pts/0
crw--w---- 1 pi   tty  136, 1 nov  5 16:33 /dev/pts/1
c--------- 1 root root   5, 2 gen  1  1970 /dev/pts/ptmx

if i understood anything i think i should find all the messages from remote nodes in /dev/ttyMySensorsGateway but it isn't working like this.
Can you help me please?