Navigation

    • Register
    • Login
    • OpenHardware.io
    • Categories
    • Recent
    • Tags
    • Popular
    1. Home
    2. MisterMel
    3. Best
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    Best posts made by MisterMel

    • !TSM:FPAR:NO REPLY

      I'm trying to set up a basic MySensors network. I have a NodeMCU hooked up to a NRF24L01+ with attena. It looks like it boots up normally. I also have an Arduino Nano hooked up to another NRF24 of the same type, but it has !TSM:FPAR:NO REPLY messages in the Serial console.

      Gateway log:

      79 MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2
      136 TSF:LRT:OK
      152 TSM:INIT
      165 TSF:WUR:MS=0
      189 TSM:INIT:TSP OK
      scandone
      state: 0 -> 2 (b0)
      state: 2 -> 3 (0)
      state: 3 -> 5 (10)
      add 0
      aid 10
      cnt 
      
      connected with REDACTED, channel 10
      dhcp client start...
      ip:192.168.178.84,mask:255.255.255.0,gw:192.168.178.1
      426 TSM:INIT:GW MODE
      449 TSM:READY:ID=0,PAR=0,DIS=0
      481 MCO:REG:NOT NEEDED
      1580 GWT:TIN:CONNECTING...
      2608 GWT:TIN:CONNECTING...
      scandone
      3636 GWT:TIN:CONNECTING...
      3665 GWT:TIN:IP: 192.168.178.84
      3699 MCO:BGN:STP
      3717 MCO:BGN:INIT OK,TSP=1
      3745 TSM:READY:NWD REQ
      3772 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
      pm open,type:2 0
      

      It does not output any more messages after that.

      Node log:

       
       __  __       ____
      |  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
      | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
      | |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
      |_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
              |___/                      2.3.2
      
      16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=16,REL=255,VER=2.3.2
      26 TSM:INIT
      28 TSF:WUR:MS=0
      34 TSM:INIT:TSP OK
      36 TSM:INIT:STATID=10
      38 TSF:SID:OK,ID=10
      39 TSM:FPAR
      1855 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      3863 !TSM:FPAR:NO REPLY
      3865 TSM:FPAR
      5681 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      7688 !TSM:FPAR:NO REPLY
      7690 TSM:FPAR
      9505 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      11512 !TSM:FPAR:NO REPLY
      11514 TSM:FPAR
      13330 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      15338 !TSM:FPAR:FAIL
      15339 TSM:FAIL:CNT=1
      15341 TSM:FAIL:DIS
      15343 TSF:TDI:TSL
      

      This continues for a bit but it's just the same messages again.

      A few notes:

      • Both radios have 100uF capacitors
      • I'm 99% they aren't fakes, they don't have the blob thingies
      • I have not set up a controller yet, but the node has a static ID defined
      • The gateway's NRF24 is at about 3.1v, the node's is at exactly 3.3v
      • I have tried setting both of them to RF24_PA_MIN, this did not make a difference
      • I have tried switching out the NodeMCU, but this did not make a difference

      Any suggestions? Is this a hardware issue? I salvaged both NRF's from a previous project, and I couldn't get them to work then either. They might just not work.

      posted in Troubleshooting
      MisterMel
      MisterMel
    • RE: !TSM:FPAR:NO REPLY

      It's a ESP8266. How far apart should I move them? I've tried up to 10m, which I think should be more than enough. I'll order new NRF's, if that doesn't fix it I guess I will just have some extras. 🤷‍♂️

      posted in Troubleshooting
      MisterMel
      MisterMel
    • RE: !TSM:FPAR:NO REPLY

      It works now! I'm now using the NRF's without external antenna and I've added a AMS1117 3.3v regulator module to the node. The ones with external antenna still don't work, but the it will probably be fine without them.

      posted in Troubleshooting
      MisterMel
      MisterMel