@dbemowsk Nice to see that you got it working! Behinde my tv there is a USB port that is powered only when the TV is on. Maybe its the same on your tv and that way you could check if the TV is on it not.

@TRS-80 For some reason, if i'm sending request too frequently the response from the TV get mixed up and unreadible. Sometimes it takes few seconds for the responses too arrive.

If I'm also changing volume or maybe channel via arduino and that is happening at the same time as arduino is checking power status, it will get som weird response. But this is only a problem when the TV is on, so you have point. I should be able to change the frequens when the power is off to maybe 5 seconds and keep 30 seconds when the power is on.

@sundberg84 That´s too bad! I thought it would work with the 3.5 mm plug.
It would be funny to see the salespersons reaction when you are in the store and asks after a TV with a RS232 port!

@sundberg84 Sounds like it would work! Looking forward too see the result! :smiley:

@tbowmo said:

@Smurphen

Now, that's cool.. I have thought about doing something similar, to detect if my tv (also an LG) is turned on. And use that to control some lightning in the living room. But as so many other things, it's only on the idea stage at the moment..

Thanks!

I'm currently doing that. When my TV turns on, the light behind my TV also turns on. But because I don't want to spam my TV with requests, there can be up to 30 seconds delay before Domoticz knows that the TV is on or not. But there is also a USB port behind my TV. I have noticed that there is only power in the USB when the TV is on. So I thinking of connecting the USB port to my Arduino to check if the power is on or not.

@sundberg84 said:

Nice! I will check my Samsung if I can do that!
Great job.

Thanks!

In my "research" I found out that some Samsung TV's and other manufactors have a serial port that can be controlled like this.

@hek said:

Nice!

Make sure to add your project to OpenHardware.io and tag it with "MySensors" and "Contest2016" :)

Thanks, I will do that!

Hi!
I just got my TV controller working and would like to share this to you.

Behind my LG TV there is a RS232 port. I have always been curious what that port does. Then I read the manual (after 5 years of curiosity) and apparently you can control almost everything in the TV with simple serial commands and it´s well documented in the manual.

The commands are built in three segments: “[COMMAND] [TV ID] [VALUE]”. For example, if I would like to turn on my TV, the command is Serial.println(“ka 01 01”), where “ka” is the command for power. To turn it off again I use Serial.println(“ka 01 00”). You can also check if the TV is on or off via the command Serial.println(“ka 01 FF”) and it will return “a 01 OK01” (on) or “a 01 OK00” (off).

After testing the commands from my computer via null modem cable I ordered a RS232 to TTL converter module. A simple way to use software serial to control RS232. The hardware is simple to set up. I use a 5v Arduino Mini Pro, the RS232 to TTL, mini usb BOB (only for power source) and of course the NRF24L01 radio with a socket adapter.

I bought this one: RS232 To TTL Converter Module

• Connect the radio like always.
• Connect the VCC on RS232 to 5v, ground to ground, RX to D6 and TX to D7

With this code I can controll the power and volume on the TV. I can also see if the TV is on or off.

#include <MySensor.h>
#include <SPI.h>
#include <SoftwareSerial.h>

MySensor gw;
MyMessage msg(1, V_LIGHT);
MyMessage msg2(2, V_PERCENTAGE);

//Software Serial for RS232 to TTL board, define output pins
SoftwareSerial mySerial(6, 7); // RX, TX

String tvPower = "00"; //Power 00=off 01=on
int tvVolume = 0; //Volume
const String tvid = "01"; //The ID you set in your TV
unsigned long previousMillis = 0; // last time update
int messageToSend = 0;

void setup()  
{   
  // Initialize library and add callback for incoming messages
  gw.begin(incomingMessage, AUTO, true);
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("LG TV RS232", "1.1");
  gw.present(1, S_LIGHT);
  gw.present(2, S_DIMMER);

  //Software Serial for RS232 to TTL board, begin
  mySerial.begin(9600);
  
}


void loop() 
{
  // Alway process incoming messages whenever possible
  gw.process();
  if (mySerial.available() > 0) {
    String incommingString;
      // read the incoming byte:
      //incomingByte = mySerial.read();
      // say what you got:
      incommingString = mySerial.readStringUntil('\n');
      Serial.print("I received: ");
      Serial.println(incommingString);
      parseSerialString(incommingString);
  }


  //Check if TV is on
  unsigned long currentMillis = millis();
  if(currentMillis - previousMillis > 30000) {
     previousMillis = currentMillis;
     if(messageToSend>0) messageToSend=0;
     if(messageToSend==0){
      sendMessage("ka", "FF"); //Set status to FF if you want to see the current power status.
      messageToSend++;
     }else if(messageToSend==1){
      sendMessage("kf", "FF"); //Set status to FF if you want to see the current volume.
      messageToSend++;    
     }
  }
}

void incomingMessage(const MyMessage &message) {
  if (message.sensor==1) {
     if(message.getBool()){
      setPower("01");
     }else{
      setPower("00"); 
     }
     // Store state in eeprom
     gw.saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
  else if (message.sensor == 2) {
    Serial.println( "V_PERCENTAGE command received..." );  
    int dimvalue= atoi( message.data );
    if ((dimvalue<0)||(dimvalue>100)) {
      Serial.println( "V_DIMMER data invalid (should be 0..100)" );
      return;
    }else{
      Serial.print("V_PERCENTAGE value: ");
      Serial.println(dimvalue);
    }
    gw.saveState(message.sensor, dimvalue);
    dimvalue = round(dimvalue*2/10);
    Serial.print("New value: ");
    Serial.println(dimvalue);
    setVolume(dimvalue);
  }
}


//Send message to tv
void sendMessage(String tvcommand, String tvstatus){
  mySerial.println(tvcommand + " " + tvid + " " + tvstatus);
}

//Turn TV on or off
void setPower(String tvstatus){
  sendMessage("ka", tvstatus);
}
//Set TV volume
void setVolume(int volume){
  String strVolume;
  if(volume<0) volume=0;
  if(volume>64) volume=64;
  strVolume = String(volume, HEX);
  if(strVolume.length()==1){
    strVolume = "0" + strVolume;
  }
  sendMessage("kf", strVolume);
}

//Parse incomming serial string
void parseSerialString(String serialString){
  String tvcommand;
  String tvstatus;
  tvcommand = serialString.substring(0,1);
  tvstatus = serialString.substring(7,9);
  if(tvcommand=="a"){
    tvPower = tvstatus;
    gw.send(msg.set(tvPower.toInt()));
    Serial.println("Power is: " + tvPower);
  }
  if(tvcommand=="f"){
    tvVolume = tvstatus.toInt();
    gw.send(msg.set(tvVolume));
    Serial.println("Volume is: " + tvstatus);
  }
}

Any feedback on the code is welcome! This is my first project for MySensors and I have a lot to learn!