@hek

is this done at startup from the node? or for each message that will be send separately?
is it possible to configure that it has to transmit by a certain repeater node (so not shortest way, but best signal)?

thanks!

is it possible to use multiple repeaters?

so:
Gateway --> repeater node --> repeater node --> sensor node

do i have to do something special for this?
because i have a feeling this is not working for me :s

but anyway how to get the different dimmer value's from the controller stays the same ;) and i am still troubling on that :s

@korttoma said:

My RGBW sketch is basically 4 dimmers also, take a look in this thread:

http://forum.mysensors.org/topic/1939/scripting-scenes-for-rgb-strip-best-way-to-control-mysensors-rgbw-node-from-vera/6

thanks for the reply!

I dont really get your code... you receive a byte from the controller? / you use a 'mode' to set your dimmers? my dimmers are 4 induvidual dimmers and dont have to work together ..

@rvendrame said:

@thomasdc , as simple as

 // Channel Number
  int i = message.sensor;

Thank you very much for the reply!
can you expain it a litle more?

so i have 4 dimmers:

MyMessage dimmer1Msg(AC_pin1, V_DIMMER);
MyMessage light1Msg(AC_pin1, V_LIGHT);
MyMessage dimmer2Msg(AC_pin2, V_DIMMER);
MyMessage light2Msg(AC_pin2, V_LIGHT);
MyMessage dimmer3Msg(AC_pin2, V_DIMMER);
MyMessage light3Msg(AC_pin3, V_LIGHT);
MyMessage dimmer4Msg(AC_pin4, V_DIMMER);
MyMessage light4Msg(AC_pin4, V_LIGHT);

how do i get the vallue for each dimmer?
so how do i get an 'int i' for channel one, an 'int j' for channel two, and so on ?
where do i put the code? is it just behind the:

void incomingMessage(const MyMessage &message) {
  if (message.type == V_LIGHT || message.type == V_DIMMER) {

? do i have to change something in the 'void incomming message' (see above)

big thanks!

hi!

after long searching and trying i managed to Build an 'MySensors' AC dimming node.
I bought this:
http://www.ebay.com/itm/4CH-AC-Dimmer-Module-Controller-Board-ARDUINO-RASPBERRY-Compatible-50-60Hz-/121752461158?ssPageName=ADME:X:RTQ:US:1123
and i use it to control my lightning.

regards, Thomas

It was working for 1 dimmer but now im am updating the code for '4' dimmers but i am having trouble with understanding...
this is the code so far:

/*
this is based on the sketch from Quocanhcgd 
link: http://forum.mysensors.org/topic/1316/ac-dimmer-with-openhab

Tested With Domoticz, working fine 220V 50Hz

AC Light Control
Uses up and down buttons to set levels
makes use of a timer interrupt to set the level of dimming
*/
#include <SPI.h>
#include <MySensor.h>  
#include <TimerOne.h>

#define SN "AC Dimmer control"
#define SV "1.0"
#define NODE_ID 30  //change to a number to assign a specific ID
#define FADE_DELAY 18  // Delay in ms for each percentage fade up/down (10ms = 1s full-range dim)
#define FADE_PERCENTAGE 5 //The percentage the fade level will be changed when a button is pressed
volatile int i=0;               // Variable to use as a counter of dimming steps. It is volatile since it is passed between interrupts
volatile int j=0;  
volatile int k=0;  
volatile int l=0;  
volatile boolean zero_cross=0;  // Flag to indicate we have crossed zero
int AC_pin1 = 4;                 // Output to Opto Triac
int AC_pin2 = 5;  
int AC_pin3 = 6;  
int AC_pin4 = 7;  

int freqStep = 75;              // This is the delay-per-brightness step in microseconds. It allows for 128 steps
                                // If using 60 Hz grid frequency set this to 65
MySensor gw;
//Tuy chinh lai
static int currentLevel1 = 128;  // Current dim level...
static int currentLevel2 = 128;  // Current dim level...
static int currentLevel3 = 128;  // Current dim level...
static int currentLevel4 = 128;  // Current dim level...

uint8_t fadeLevel1 = 128; //used to store the fade level when using the buttons
uint8_t fadeLevel2 = 128:
uint8_t fadeLevel3 = 128;
uint8_t fadeLevel4 = 128:

MyMessage dimmer1Msg(AC_pin1, V_DIMMER);
MyMessage light1Msg(AC_pin1, V_LIGHT);
MyMessage dimmer2Msg(AC_pin2, V_DIMMER);
MyMessage light2Msg(AC_pin2, V_LIGHT);
MyMessage dimmer3Msg(AC_pin2, V_DIMMER);
MyMessage light3Msg(AC_pin3, V_LIGHT);
MyMessage dimmer4Msg(AC_pin4, V_DIMMER);
MyMessage light4Msg(AC_pin4, V_LIGHT);

void setup() {  // Begin setup
  Serial.begin(115200);
  /// - Setup Mysensors
  Serial.println( SN ); 
  gw.begin( incomingMessage,  NODE_ID, true);
  // Register the LED Dimmable Light with the gateway
    gw.present( AC_pin1, S_DIMMER );
    gw.present( AC_pin2, S_DIMMER );
    gw.present( AC_pin3, S_DIMMER );
    gw.present( AC_pin4, S_DIMMER );
     
  gw.sendSketchInfo(SN, SV);
  
  // Pull the gateway's current dim level - restore light level upon sendor node power-up
  gw.request( AC_pin1, V_DIMMER );
  gw.request( AC_pin2, V_DIMMER );
  gw.request( AC_pin3, V_DIMMER );
  gw.request( AC_pin4, V_DIMMER );
  
  //Setup AC PIN  // Set the Triac pin as output
   pinMode(AC_pin1, OUTPUT);  
   pinMode(AC_pin2, OUTPUT);
   pinMode(AC_pin3, OUTPUT);
   pinMode(AC_pin4, OUTPUT);
     
 // Set the Triac pin as output
 
  attachInterrupt(1, zero_cross_detect, RISING);    // Attach an Interupt to Pin 2 (interupt 0) for Zero Cross Detection
  Timer1.initialize(freqStep);                      // Initialize TimerOne library for the freq we need
  Timer1.attachInterrupt(dim_check, freqStep);      // Go to dim_check procedure every 75 uS (50Hz)  or 65 uS (60Hz)
  // Use the TimerOne Library to attach an interrupt
  
}

void zero_cross_detect() {    
  zero_cross = true;               // set flag for dim_check function that a zero cross has occured
  i=0;                             // stepcounter to 0.... as we start a new cycle
  digitalWrite(AC_pin1, LOW);
  digitalWrite(AC_pin2, LOW);
  digitalWrite(AC_pin3, LOW);
  digitalWrite(AC_pin4, LOW);
}                                 

// Turn on the TRIAC at the appropriate time
// We arrive here every 75 (65) uS
// First check if a flag has been set
// Then check if the counter 'i' has reached the dimming level
// if so.... switch on the TRIAC and reset the counter



void dim_check1() {                   
  if(zero_cross == true) {              
    if(i>=fadeLevel1) {                     
      digitalWrite(AC_pin1, HIGH);  // turn on light       
      i=0;  // reset time step counter                         
      zero_cross=false;    // reset zero cross detection flag
    } 
    else {
      i++;  // increment time step counter                     
    }                                
  }    
}

void dim_check2() {                   
  if(zero_cross == true) {              
    if(j>=fadeLevel2) {                     
      digitalWrite(AC_pin2, HIGH);  // turn on light       
      j=0;  // reset time step counter                         
      zero_cross=false;    // reset zero cross detection flag
    } 
    else {
      j++;  // increment time step counter                     
    }                                
  }    
}


void dim_check3() {                   
  if(zero_cross == true) {              
    if(k>=fadeLevel3) {                     
      digitalWrite(AC_pin3, HIGH);  // turn on light       
      k=0;  // reset time step counter                         
      zero_cross=false;    // reset zero cross detection flag
    } 
    else {
      k++;  // increment time step counter                     
    }                                
  }    
}

void dim_check4() {                   
  if(zero_cross == true) {              
    if(l>=fadeLevel4) {                     
      digitalWrite(AC_pin4, HIGH);  // turn on light       
      l=0;  // reset time step counter                         
      zero_cross=false;    // reset zero cross detection flag
    } 
    else {
      l++;  // increment time step counter                     
    }                                
  }    
}

                            

void loop() {  
    gw.process();
}

void incomingMessage(const MyMessage &message) {
  if (message.type == V_LIGHT || message.type == V_DIMMER) {
    
    //  Retrieve the power or dim level from the incoming request message
    int requestedLevel = atoi( message.data );
    
    // Adjust incoming level if this is a V_LIGHT variable update [0 == off, 1 == on]
    requestedLevel *= ( message.type == V_LIGHT ? 100 : 1 );
    
    // Clip incoming level to valid range of 0 to 100
    requestedLevel = requestedLevel > 100 ? 100 : requestedLevel;
    requestedLevel = requestedLevel < 0   ? 0   : requestedLevel;
    
   
    float percent_level;
    percent_level = 128 - (requestedLevel * 1.28);
    fadeToLevel( percent_level );
     Serial.print( "Changing level to " );
    Serial.print( requestedLevel );
    Serial.print( ", from " ); 
    Serial.println( currentLevel );
    // Inform the gateway of the current DimmableLED's SwitchPower1 and LoadLevelStatus value...
   //  gw.send(lightMsg.set(currentLevel > 0 ? 1 : 0));
     // gw.send( dimmerMsg.set(currentLevel) );
      }
}

/***
 *  This method provides a graceful fade up/down effect
 */
void fadeToLevel( int toLevel ) {
  Serial.print("toLevel Value: ");
 Serial.println(toLevel);
  
  int delta = ( currentLevel - toLevel ) < 0 ? 1 : -1;
  Serial.print("delta Value: ");
 Serial.println(delta);
  while ( currentLevel != toLevel ) {
    currentLevel += delta;

 fadeLevel= ((int)currentLevel);
    delay( FADE_DELAY );

  }
  
}

I have trouble understanding this part:
void incomingMessage(const MyMessage &message) {
if (message.type == V_LIGHT || message.type == V_DIMMER)

all 4 dimmers are type V_LIGHT and V_DIMMER
how do i get the right dimmer value from the controller from each different dimmer?

someone who can help me with the rest of the code?

thanks!

https://www.domoticz.com/forum/viewtopic.php?f=38&t=8033

were you (someone) able to debug the 'fading' funciton in the code? i think its a problem in the while loop in the arduino/mysensors code the while loop is done, but only when the while loop is comletely through , the 'dimvalue' gets updated/changed

EDIT:
this works!

/*
AC Light Control
Uses up and down buttons to set levels
makes use of a timer interrupt to set the level of dimming
*/
#include <SPI.h>
#include <MySensor.h>  
#include <TimerOne.h>

#define SN "AC Dimmer control"
#define SV "1.0"
#define NODE_ID 30  //change to a number to assign a specific ID
#define FADE_DELAY 50  // Delay in ms for each percentage fade up/down (10ms = 1s full-range dim)
#define FADE_PERCENTAGE 5 //The percentage the fade level will be changed when a button is pressed
volatile int i=0;               // Variable to use as a counter of dimming steps. It is volatile since it is passed between interrupts
volatile boolean zero_cross=0;  // Flag to indicate we have crossed zero
int AC_pin = 6;                 // Output to Opto Triac

int freqStep = 75;              // This is the delay-per-brightness step in microseconds. It allows for 128 steps
                                // If using 60 Hz grid frequency set this to 65
MySensor gw;
//Tuy chinh lai
static int currentLevel = 128;  // Current dim level...
uint8_t fadeLevel = 128; //used to store the fade level when using the buttons
uint8_t upPreviousValue;
uint8_t downPreviousValue;
uint8_t powerPreviousValue;


MyMessage dimmerMsg(AC_pin, V_DIMMER);
MyMessage lightMsg(AC_pin, V_LIGHT);



// =Het tuy chinh lai


void setup() {  // Begin setup
  Serial.begin(115200);
  /// - Setup Mysensors
  Serial.println( SN ); 
  gw.begin( incomingMessage,  NODE_ID, true);
  // Register the LED Dimmable Light with the gateway
  gw.present( 6, S_DIMMER );
  
  gw.sendSketchInfo(SN, SV);
  // Pull the gateway's current dim level - restore light level upon sendor node power-up
  gw.request( 6, V_DIMMER );


  
  //Setup AC PIN
  pinMode(AC_pin, OUTPUT);                          // Set the Triac pin as output
  attachInterrupt(1, zero_cross_detect, RISING);    // Attach an Interupt to Pin 2 (interupt 0) for Zero Cross Detection
  Timer1.initialize(freqStep);                      // Initialize TimerOne library for the freq we need
  Timer1.attachInterrupt(dim_check, freqStep);      // Go to dim_check procedure every 75 uS (50Hz)  or 65 uS (60Hz)
  // Use the TimerOne Library to attach an interrupt
  
}

void zero_cross_detect() {    
  zero_cross = true;               // set flag for dim_check function that a zero cross has occured
  i=0;                             // stepcounter to 0.... as we start a new cycle
  digitalWrite(AC_pin, LOW);
}                                 

// Turn on the TRIAC at the appropriate time
// We arrive here every 75 (65) uS
// First check if a flag has been set
// Then check if the counter 'i' has reached the dimming level
// if so.... switch on the TRIAC and reset the counter

void dim_check() {                   
  if(zero_cross == true) {              
    if(i>=fadeLevel) {                     
      digitalWrite(AC_pin, HIGH);  // turn on light       
      i=0;  // reset time step counter                         
      zero_cross=false;    // reset zero cross detection flag
    } 
    else {
      i++;  // increment time step counter                     
    }                                
  }    
}

                            

void loop() {  
    gw.process();
}

void incomingMessage(const MyMessage &message) {
  if (message.type == V_LIGHT || message.type == V_DIMMER) {
    
    //  Retrieve the power or dim level from the incoming request message
    int requestedLevel = atoi( message.data );
    
    // Adjust incoming level if this is a V_LIGHT variable update [0 == off, 1 == on]
    requestedLevel *= ( message.type == V_LIGHT ? 100 : 1 );
    
    // Clip incoming level to valid range of 0 to 100
    requestedLevel = requestedLevel > 100 ? 100 : requestedLevel;
    requestedLevel = requestedLevel < 0   ? 0   : requestedLevel;
    
   
    float percent_level;
    percent_level = 128 - (requestedLevel * 1.28);
    fadeToLevel( percent_level );
     Serial.print( "Changing level to " );
    Serial.print( requestedLevel );
    Serial.print( ", from " ); 
    Serial.println( currentLevel );
    // Inform the gateway of the current DimmableLED's SwitchPower1 and LoadLevelStatus value...
   //  gw.send(lightMsg.set(currentLevel > 0 ? 1 : 0));

    // hek comment: Is this really nessesary?
   // gw.send( dimmerMsg.set(currentLevel) );

  
    }
}

/***
 *  This method provides a graceful fade up/down effect
 */
void fadeToLevel( int toLevel ) {
  Serial.print("toLevel Value: ");
 Serial.println(toLevel);

  
  int delta = ( currentLevel - toLevel ) < 0 ? 1 : -1;
  Serial.print("delta Value: ");
 Serial.println(delta);
  while ( currentLevel != toLevel ) {
    currentLevel += delta;

 fadeLevel= ((int)currentLevel);
    delay( FADE_DELAY );
    //fadeLevel = toLevel;

   

  }


  
}