💬 Relay

[b0wi]

The script for 'Example with button' works perfectly! Thanks for that.
Has someone a script for multiple Relays with buttons ready to use for me?
I want to use it in my garden to switch the lights with physical buttons and also control them with Domoticz.

[jimmy loyens]

This post is deleted!

[badmannen]

I am having this particular switch to be recognized in "Mozilla WEBTHINGS".

IS there some issue with having a repeater node and sensors/switches etc attaches to it? .. it sends in the data as it should when I check with MYSController and I can switch it from there with sending "V_STATUS" messages. but no luck so far of getting the sensors appear in WEBTHINGS , every other sensor works fine.

[Seawolf]

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enables and select radio type (if attached)
#define MY_RADIO_RF24
//#define MY_RADIO_RFM69
//#define MY_RADIO_RFM95

#define MY_GATEWAY_ESP8266

#define MY_WIFI_SSID "SSID"
#define MY_WIFI_PASSWORD "PSW"

// Enable UDP communication
//#define MY_USE_UDP // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below

// Set the hostname for the WiFi Client. This is the hostname
// it will pass to the DHCP server if not static.
#define MY_HOSTNAME "ESP8266_GW"

// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
//#define MY_IP_ADDRESS 192,168,0,0

// If using static ip you can define Gateway and Subnet address as well
//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
//#define MY_IP_SUBNET_ADDRESS 255,255,255,0

// The port to keep open on node server mode
#define MY_PORT 5003

// How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
//#define MY_CONTROLLER_URL_ADDRESS "my.controller.org"

// Enable inclusion mode
//#define MY_INCLUSION_MODE_FEATURE

// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
//#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN D1

// Set blinking period
//#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
// Led pins used if blinking feature is enabled above
//#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED
#define LWIP_OPEN_SRC whatever
#define TCP_MSS whatever
#define LWIP_IPV6 whatever
#define LWIP_FEATURES whatever

#include <MySensors.h>
#include <SPI.h>
//DHT with autodetection

#include <dhtnew.h>

DHTNEW mySensor(5); // ESP 16 UNO 6

uint32_t count = 0;
uint32_t start, stop;

uint32_t errors[10] = { 0,0, 0,0, 0,0, 0,0, 0,0 };

//Domoticz
#define CHILD_ID_HUM 2
#define CHILD_ID_TEMP 3
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);

void presentation()
{
// Send the sketch version information to the gateway
sendSketchInfo("TemperatureAndHumidity", "1.1");

// Register all sensors to gw (they will be created as child devices)
present(CHILD_ID_HUM, S_HUM);
present(CHILD_ID_TEMP, S_TEMP);

}

void setup()
{
Serial.begin(115200);
Serial.println("DHT_endless.ino");
Serial.print("LIBRARY VERSION: ");
Serial.println(DHTNEW_LIB_VERSION);
Serial.println();
}

void loop()
{
count++;
// show counters for OK and errors.
if (count % 50 == 0)
{
Serial.println();
Serial.println("OK \tCRC \tTOA \tTOB \tTOC \tTOD \tSNR \tBS \tUNK");
for (uint8_t i = 0; i < 9; i++)
{
Serial.print(errors[i]);
Serial.print('\t');
}
Serial.println();
Serial.println();
}

if (count % 10 == 0)
{
Serial.println();
Serial.println("TIM\tCNT\tSTAT\tHUMI\tTEMP\tTIME\tTYPE");
}
Serial.print(millis());
Serial.print("\t");
Serial.print(count);
Serial.print("\t");

start = micros();
int chk = mySensor.read();
stop = micros();

switch (chk)
{
case DHTLIB_OK:
Serial.print("OK,\t");
errors[0]++;
break;
case DHTLIB_ERROR_CHECKSUM:
Serial.print("CRC,\t");
errors[1]++;
break;
case DHTLIB_ERROR_TIMEOUT_A:
Serial.print("TOA,\t");
errors[2]++;
break;
case DHTLIB_ERROR_TIMEOUT_B:
Serial.print("TOB,\t");
errors[3]++;
break;
case DHTLIB_ERROR_TIMEOUT_C:
Serial.print("TOC,\t");
errors[4]++;
break;
case DHTLIB_ERROR_TIMEOUT_D:
Serial.print("TOD,\t");
errors[5]++;
break;
case DHTLIB_ERROR_SENSOR_NOT_READY:
Serial.print("SNR,\t");
errors[6]++;
break;
case DHTLIB_ERROR_BIT_SHIFT:
Serial.print("BS,\t");
errors[7]++;
break;
default:
Serial.print("U");
Serial.print(chk);
Serial.print(",\t");
errors[8]++;
break;
}
// DISPLAY DATA
#ifdef MY_DEBUG
Serial.print(mySensor.getHumidity(), 1);
Serial.print(",\t");
Serial.print(mySensor.getTemperature(), 1);
Serial.print(",\t");
Serial.print(stop - start);
Serial.print(",\t");
Serial.println(mySensor.getType());
#endif

//send to gateway
float humidity = mySensor.getHumidity();
send(msgHum.set(humidity, 1));
float temperature = mySensor.getTemperature();
send(msgTemp.set(temperature, 1));

delay(3000);
}

// -- END OF FILE --

[Seawolf]

I was so happy to have finaly a fonctionnal sketch for my esp8266 gateway whith the DHT22 that i post directly my code.
I hope that it will help some people.
based on: https://github.com/RobTillaart/DHTNew/blob/master/examples/dhtnew_endless/dhtnew_endless.ino

[joaoabs]

Hi,
Trying to go deep on the API and come this this doubt: The second example (with button) the child seems to be declared as "S_LIGHT" and the receiving messages are "V_LIGHT", while the first example seems better suitable for a relay (child as "S_BINNARY" and requests as "V_STATUS").
I haven't found any "S_LIGHT" or "V_LIGHT" in the API, only "S_LIGHT_LEVEL" and "V_LIGHT_LEVEL". What is the most suitable type for a relay node with a local button?

[skywatch]

@joaoabs A realy usually has only 2 states, on and off. So I would use S-BINARY and V_STATUS every time.

A changeover realy also has 2 states so again I would go for binary and status.

Light_Level is more suited to getting light levels from a sensor or sending a light level to a dimmable light.

[TheoL]

Not sure if it ever has mentioned before, but the first example contains

// Enable and select radio type attached
#define MY_RADIO_RF24

Which results in a compile error

MySensors.h:287:4: error: #error No forward link or gateway feature activated. This means nowhere to send messages! Pretty pointless.
   #error No forward link or gateway feature activated. This means nowhere to send messages! Pretty pointless.

It should be:

// Enable and select radio type attached
#define MY_RADIO_NRF24

And then it compiles and works :)

[mfalkvidd]

@TheoL which version of MySensors are you using when compiling?

The change from NRF24 to RF24 was intentional.

https://github.com/mysensors/MySensorsArduinoExamples/commit/36bee0b7426cc3955d23b3f4918da64fd2cc49ad#diff-1252bb46b9b35d77138b7fd96c37e4d3efa629af89ac0d1c2302cde6cf755ea4

Documentation: https://www.mysensors.org/apidocs/group__RF24SettingGrpPub.html#gad9d7b3f6173e32fa96468e05b901acba

[TheoL]

@mfalkvidd I'm in an older version I discovered. Ran across more small differences.

[skywatch]

@TheoL Sound like a good time to update to the latest version. it is the best yet and very stable.