Multisensor PIR problem [solved]

rvendrame

It makes sense ;-) Try this:

create (outside the loop) a variable to count the time:

long mytime = 0;

.. and replace the delay by :

 if ( milis() > mytime )  { 

   <  Put the dht stuff here > 

  mytime = millis() + dht.getMinimumSamplingPeriod() ; 

}

n3ro

@rvendrame

hmm :)
if is use this:

#include <MySensor.h>
#include <readVcc.h>
#include <SPI.h>
#include <DHT.h>


#define NODE_ID 10                       // ID of node
unsigned long SLEEP_TIME = 10000;        // Sleep time between reports (in milliseconds)

#define CHILD_ID_PIR 1                   // Id of the sensor PIR
#define CHILD_ID_HUM 2                   // Id of the sensor HUM
#define CHILD_ID_TEMP 3                  // Id of the sensor TEMP
#define CHILD_ID_LIGHT 4                 // Id of the sensor LIGHT

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

MySensor gw;
// Initialize Variables
MyMessage msgPir(CHILD_ID_PIR, V_TRIPPED);
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msgLight(CHILD_ID_LIGHT, V_LIGHT_LEVEL);

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
int oldBatteryPcnt;
int lastLightLevel;
long mytime = 0;


int MIN_V = 2700; // empty voltage (0%)
int MAX_V = 3200; // full voltage (100%)

void setup()
{
  gw.begin(NULL, NODE_ID, false);

  //PIR
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Motion Sensor", "1.0");

  pinMode(PIR_SENSOR_DIGITAL, INPUT);      // sets the motion sensor digital pin as input
  digitalWrite(PIR_SENSOR_DIGITAL, HIGH);
  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_PIR, S_MOTION);

  //DHT
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);

  // Send the Sketch Version Information to the Gateway
  gw.sendSketchInfo("Humidity", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);

  metric = gw.getConfig().isMetric;

  //LIGHT
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Light Sensor", "1.0");

  // Register all sensors to gateway (they will be created as child devices)
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);

}

void loop()
{



  // Read digital motion value
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  Serial.print("---------- PIR: ");
  Serial.println(tripped);
  gw.send(msgPir.set(tripped ? "1" : "0")); // Send tripped value to gw


  if ( millis() > mytime )  {

    //DHT
    delay(dht.getMinimumSamplingPeriod());

    float temperature = dht.getTemperature();
    if (isnan(temperature)) {
      Serial.println("Failed reading temperature from DHT");
    } else if (temperature != lastTemp) {
      lastTemp = temperature;
      if (!metric) {
        temperature = dht.toFahrenheit(temperature);
      }
      gw.send(msgTemp.set(temperature, 1));
      Serial.print("---------- Temp: ");
      Serial.println(temperature);
    }

    float humidity = dht.getHumidity();
    if (isnan(humidity)) {
      Serial.println("Failed reading humidity from DHT");
    } else if (humidity != lastHum) {
      lastHum = humidity;
      gw.send(msgHum.set(humidity, 1));
      Serial.print("---------- Humidity: ");
      Serial.println(humidity);
    }
    // Light
    int lightLevel = (1023 - analogRead(LIGHT_SENSOR_ANALOG_PIN)) / 10.23;
    //Serial.println(lightLevel);
    if (lightLevel != lastLightLevel) {
      gw.send(msgLight.set(lightLevel));
      lastLightLevel = lightLevel;
      Serial.print("---------- Light: ");
      Serial.println(lightLevel);
    }
    // Measure battery
    float batteryV = readVcc();
    int batteryPcnt = (((batteryV - MIN_V) / (MAX_V - MIN_V)) * 100 );
    if (batteryPcnt > 100) {
      batteryPcnt = 100;
    }

    if (batteryPcnt != oldBatteryPcnt) {
      gw.sendBatteryLevel(batteryPcnt); // Send battery percentage
      oldBatteryPcnt = batteryPcnt;
    }
    Serial.print("---------- Battery: ");
    Serial.println(batteryPcnt);

    mytime = millis() + dht.getMinimumSamplingPeriod();
 
  }
     Serial.println(mytime);
  // Sleep until interrupt comes in on motion sensor. Send update every two minute.
  gw.sleep(INTERRUPT, CHANGE, SLEEP_TIME);
}

i get this output:
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
6608
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
6608
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
6608
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
6608
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
send: 10-10-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
send: 10-10-0-0 s=2,c=1,t=1,pt=7,l=5,st=fail:41.7
---------- Humidity: 41.70
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=fail:38
---------- Light: 38
---------- Battery: 100
11148
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
11148
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
11148
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
11148
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
11148
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
send: 10-10-255-255 s=255,c=3,t=7,pt=0,l=0,st=fail:
---------- Battery: 100
15441
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
15441
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
15441
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
15441
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1

the pir sends 0 and didnt sleep right :(

rvendrame

What is this number? Did you print the milis()?

send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
6608 <<<<<<

n3ro

@n3ro said:

Serial.println(mytime);

yes :)
Serial.println(mytime);

rvendrame

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

Are you connecting both DHT and PIR at same pin 2 ? That must be the cause (DHT is triggering the interruption, I think you want only the PIR to trigger it).

Edit: looks like your PIR is at pin 3 , and DHT on pin 2 --- Should be the inverse? The PIR should be on pin 2 (to trigger the interrupt).

Sweebee

@rvendrame Pir sensor is defined as 3

interrupt pin is defined as INT1: 3 - 2 = 1

rvendrame

So PIR must connect on PIN 1 and not PIN 3.

Edit: Better, how did you connect DHT and PIR?

n3ro

@rvendrame The DHT is on pin 2 and the pir on pin 3. i use the MYS PCB.

i suspect the delay function disturb the sleep function. if i dont use the delay, the dht cant "heat up".

far as I know the interrupt is only an internal value. right?

rvendrame

Yes, it looks fine. What exactly error are you having? From your first serial monitor, it looks like your sensor woke on every 10min aprox, ( 6608 / 11148 / 15441 ).

n3ro

@rvendrame
if i use this:

#include <MySensor.h>
#include <readVcc.h>
#include <SPI.h>
#include <DHT.h>


#define NODE_ID 10                       // ID of node
unsigned long SLEEP_TIME = 600000;        // Sleep time between reports (in milliseconds)

#define CHILD_ID_PIR 1                   // Id of the sensor PIR
#define CHILD_ID_HUM 2                   // Id of the sensor HUM
#define CHILD_ID_TEMP 3                  // Id of the sensor TEMP
#define CHILD_ID_LIGHT 4                 // Id of the sensor LIGHT

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

MySensor gw;
// Initialize Variables
MyMessage msgPir(CHILD_ID_PIR, V_TRIPPED);
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msgLight(CHILD_ID_LIGHT, V_LIGHT_LEVEL);

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
int oldBatteryPcnt;
int lastLightLevel;


int MIN_V = 2700; // empty voltage (0%)
int MAX_V = 3200; // full voltage (100%)

void setup()
{
  gw.begin(NULL, NODE_ID, false);

  //PIR
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Motion Sensor", "1.0");

  pinMode(PIR_SENSOR_DIGITAL, INPUT);      // sets the motion sensor digital pin as input
  digitalWrite(PIR_SENSOR_DIGITAL, HIGH);
  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_PIR, S_MOTION);
  
  //DHT
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);

  // Send the Sketch Version Information to the Gateway
  gw.sendSketchInfo("Humidity", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);

  metric = gw.getConfig().isMetric;
  
  //LIGHT
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Light Sensor", "1.0");

  // Register all sensors to gateway (they will be created as child devices)
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);

}

void loop()
{

  // Measure battery
  float batteryV = readVcc();
  int batteryPcnt = (((batteryV - MIN_V) / (MAX_V - MIN_V)) * 100 );
  if (batteryPcnt > 100) {
    batteryPcnt = 100;
  }

  if (batteryPcnt != oldBatteryPcnt) {
    gw.sendBatteryLevel(batteryPcnt); // Send battery percentage
    oldBatteryPcnt = batteryPcnt;
  }
  Serial.print("---------- Battery: ");
  Serial.println(batteryPcnt);

  // Read digital motion value
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  Serial.print("---------- PIR: ");
  Serial.println(tripped);
  gw.send(msgPir.set(tripped ? "1" : "0")); // Send tripped value to gw


  //DHT
  //delay(dht.getMinimumSamplingPeriod());

  float temperature = dht.getTemperature();
  if (isnan(temperature)) {
    Serial.println("Failed reading temperature from DHT");
  } else if (temperature != lastTemp) {
    lastTemp = temperature;
    if (!metric) {
      temperature = dht.toFahrenheit(temperature);
    }
    gw.send(msgTemp.set(temperature, 1));
    Serial.print("---------- Temp: ");
    Serial.println(temperature);
  }

  float humidity = dht.getHumidity();
  if (isnan(humidity)) {
    Serial.println("Failed reading humidity from DHT");
  } else if (humidity != lastHum) {
    lastHum = humidity;
    gw.send(msgHum.set(humidity, 1));
    Serial.print("---------- Humidity: ");
    Serial.println(humidity);
  }
  // Light
  int lightLevel = (1023 - analogRead(LIGHT_SENSOR_ANALOG_PIN)) / 10.23;
  //Serial.println(lightLevel);
  if (lightLevel != lastLightLevel) {
    gw.send(msgLight.set(lightLevel));
    lastLightLevel = lightLevel;
    Serial.print("---------- Light: ");
    Serial.println(lightLevel);
  }
  // Sleep until interrupt comes in on motion sensor. Send update every two minute.
  gw.sleep(INTERRUPT, CHANGE, SLEEP_TIME);
}

i get this output after starting:
sensor started, id 10
send: 10-10-0-0 s=255,c=0,t=17,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=6,pt=1,l=1,st=ok:0
read: 0-0-10 s=255,c=3,t=6,pt=0,l=1:M
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=13,st=ok:Motion Sensor
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=1,c=0,t=1,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=8,st=ok:Humidity
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=2,c=0,t=7,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=3,c=0,t=6,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=12,st=ok:Light Sensor
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=4,c=0,t=16,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=0,pt=1,l=1,st=ok:100
---------- Battery: 100
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
send: 10-10-0-0 s=3,c=1,t=0,pt=7,l=5,st=ok:16.6
---------- Temp: 16.60
send: 10-10-0-0 s=2,c=1,t=1,pt=7,l=5,st=ok:43.8
---------- Humidity: 43.80
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:39
---------- Light: 39
---------- Battery: 100
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:37
---------- Light: 37
---------- Battery: 100
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:34
---------- Light: 34
---------- Battery: 100
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:36
---------- Light: 36
---------- Battery: 100
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:37
---------- Light: 37
---------- Battery: 100
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:38
---------- Light: 38

The DHT gives only output the first start and the pir interrupt works perfect.

When delay(dht.getMinimumSamplingPeriod()); is activated the DHT works and the pit interrupts the whole time :(
In this configuration the arduino never sleeps ..

sensor started, id 10
send: 10-10-0-0 s=255,c=0,t=17,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=6,pt=1,l=1,st=ok:0
read: 0-0-10 s=255,c=3,t=6,pt=0,l=1:M
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=13,st=ok:Motion Sensor
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=1,c=0,t=1,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=8,st=ok:Humidity
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=2,c=0,t=7,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=3,c=0,t=6,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=12,st=ok:Light Sensor
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=4,c=0,t=16,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=0,pt=1,l=1,st=ok:100
---------- Battery: 100
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
send: 10-10-0-0 s=3,c=1,t=0,pt=7,l=5,st=ok:16.5
---------- Temp: 16.50
send: 10-10-0-0 s=2,c=1,t=1,pt=7,l=5,st=ok:43.9
---------- Humidity: 43.90
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:38
---------- Light: 38
---------- Battery: 100
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
send: 10-10-0-0 s=3,c=1,t=0,pt=7,l=5,st=ok:16.6
---------- Temp: 16.60
send: 10-10-0-0 s=2,c=1,t=1,pt=7,l=5,st=ok:43.8
---------- Humidity: 43.80
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:37
---------- Light: 37
---------- Battery: 100
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
send: 10-10-0-0 s=3,c=1,t=0,pt=7,l=5,st=ok:16.5
---------- Temp: 16.50
---------- Battery: 100
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- Battery: 100
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
send: 10-10-0-0 s=4,c=1,t=23,pt=2,l=2,st=ok:38

EDIT: i have changed the sleeptime for testing to a shorter time

Sweebee

@rvendrame When the PIR is connected to PIN3 the interrupt is INT1. Pin 1 does not have an interrupt.

Only pin 2 and pin 3 have an interrupt.

Pin 2 = int0
pin 3 = int1

rvendrame

if you put the delay() inside that 'if ( mills() > mytime ) ' , what happens?

n3ro

@Sweebee is it possible to fix the problem when DHT is connected to pin 4?

rvendrame

@n3ro said:

s it possible to fix the problem when DHT is connected to pin 4?

It worth a try ...

n3ro

@rvendrame
i have posted it before this post:

"What is this number? Did you print the milis()?

send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=fail:0
6608 <<<<<<"

in the posted sketch the delay is inside millis

rvendrame

I didn't find the if ( millis() > my time) in the last sketch you posted ...

n3ro

if i use this

#include <MySensor.h>
#include <readVcc.h>
#include <SPI.h>
#include <DHT.h>


#define NODE_ID 10                       // ID of node
unsigned long SLEEP_TIME = 10000;        // Sleep time between reports (in milliseconds)

#define CHILD_ID_PIR 1                   // Id of the sensor PIR
#define CHILD_ID_HUM 2                   // Id of the sensor HUM
#define CHILD_ID_TEMP 3                  // Id of the sensor TEMP
#define CHILD_ID_LIGHT 4                 // Id of the sensor LIGHT

#define PIR_SENSOR_DIGITAL 3           // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT PIR_SENSOR_DIGITAL-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define HUMIDITY_SENSOR_DIGITAL_PIN 2
#define LIGHT_SENSOR_ANALOG_PIN 0

MySensor gw;
// Initialize Variables
MyMessage msgPir(CHILD_ID_PIR, V_TRIPPED);
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msgLight(CHILD_ID_LIGHT, V_LIGHT_LEVEL);

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
int oldBatteryPcnt;
int lastLightLevel;
long mytime = 0;


int MIN_V = 2700; // empty voltage (0%)
int MAX_V = 3200; // full voltage (100%)

void setup()
{
  gw.begin(NULL, NODE_ID, false);

  //PIR
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Motion Sensor", "1.0");

  pinMode(PIR_SENSOR_DIGITAL, INPUT);      // sets the motion sensor digital pin as input
  digitalWrite(PIR_SENSOR_DIGITAL, HIGH);
  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_PIR, S_MOTION);

  //DHT
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);

  // Send the Sketch Version Information to the Gateway
  gw.sendSketchInfo("Humidity", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);

  metric = gw.getConfig().isMetric;

  //LIGHT
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Light Sensor", "1.0");

  // Register all sensors to gateway (they will be created as child devices)
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);

}

void loop()
{



  // Read digital motion value
  boolean tripped = digitalRead(PIR_SENSOR_DIGITAL) == HIGH;
  Serial.print("---------- PIR: ");
  Serial.println(tripped);
  gw.send(msgPir.set(tripped ? "1" : "0")); // Send tripped value to gw


  if ( millis() > mytime )  {

    //DHT
    delay(dht.getMinimumSamplingPeriod());

    float temperature = dht.getTemperature();
    if (isnan(temperature)) {
      Serial.println("Failed reading temperature from DHT");
    } else if (temperature != lastTemp) {
      lastTemp = temperature;
      if (!metric) {
        temperature = dht.toFahrenheit(temperature);
      }
      gw.send(msgTemp.set(temperature, 1));
      Serial.print("---------- Temp: ");
      Serial.println(temperature);
    }

    float humidity = dht.getHumidity();
    if (isnan(humidity)) {
      Serial.println("Failed reading humidity from DHT");
    } else if (humidity != lastHum) {
      lastHum = humidity;
      gw.send(msgHum.set(humidity, 1));
      Serial.print("---------- Humidity: ");
      Serial.println(humidity);
    }
    mytime = millis() + dht.getMinimumSamplingPeriod();

  }
  // Sleep until interrupt comes in on motion sensor. Send update every two minute.
  gw.sleep(INTERRUPT, CHANGE, SLEEP_TIME);
}

i get this output:
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=13,st=ok:Motion Sensor
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=1,c=0,t=1,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=8,st=ok:Humidity
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=2,c=0,t=7,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=3,c=0,t=6,pt=0,l=5,st=ok:1.4.1
send: 10-10-0-0 s=255,c=3,t=11,pt=0,l=12,st=ok:Light Sensor
send: 10-10-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
send: 10-10-0-0 s=4,c=0,t=16,pt=0,l=5,st=ok:1.4.1
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
send: 10-10-0-0 s=3,c=1,t=0,pt=7,l=5,st=ok:17.2
---------- Temp: 17.20
send: 10-10-0-0 s=2,c=1,t=1,pt=7,l=5,st=ok:43.8
---------- Humidity: 43.80
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 1
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:1
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0
---------- PIR: 0
send: 10-10-0-0 s=1,c=1,t=16,pt=0,l=1,st=ok:0

Sweebee

This can't work well. Your interrupt is set on pin1 - 2 = int-1?

What happens when you remove the pir and use a switch instead?

n3ro

@Sweebee
is #define INTERRUPT PIR_SENSOR_DIGITAL-2 wrong?

when i use a switch it looks OK

rvendrame

@n3ro , what is wrong at your last test? The PIR is reporting 0 and 1, and from time to time there is a temp/hum report as well.

Multisensor PIR problem [solved]

11

12.1k

11.2k

113.4k