[SOLVED] Mysensors Lux

[the cosmic gate]

After we moved to oneother different house , is started the mysensors again.The lux sensors give this error ```

send: 1-1-0-0 s=0,c=1,t=23,pt=3,l=2,st=fail:102

[the cosmic gate]

to be honest this is the one and only sensors we connected now so i dont now what the others will tell

fot now i changes the radio already and check the capacitor , but still fails ?

[TheoL]

Stupid question. But have you checked if the gateway is up and running?

[sundberg84]

"st=fail" means the receiving node or gateway has problems sending ack back to the sending node.

As @TheoL said - are your receiving node (repeater or gateway) working? What does that log say?

Its probably a hardware issue (power and/or range). Try adding a capacitor (http://www.mysensors.org/build/connect_radio#connecting-a-decoupling-capacitor) to the receiving radio, change power source, move receiver/sender closer to each other or build a repeater.

[the cosmic gate]

This post is deleted!

[the cosmic gate]

@TheoL said:

Stupid question. But have you checked if the gateway is up and running?

Gateway log says: ok
Hmm maybe check the soldering etc

0;0;3;0;9;gateway started, id=0, parent=0, distance=0
0;0;3;0;14;Gateway startup complete.

[TheoL]

@the-cosmic-gate problems like yours aren't very easy to solve. What hapens if you place the lux sensor within a meter or 2 from the gateway?

[the cosmic gate]

problem solved issue : soma bad soldered resistor on the (china) NRF24L01+.
After i replaced the radio on the gateway

send: 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
sensor started, id=1, parent=0, distance=1
send: 1-1-0-0 s=255,c=3,t=11,pt=0,l=16,sg=0,st=ok:Light Lux Sensor
send: 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 1-1-0-0 s=0,c=0,t=16,pt=0,l=0,sg=0,st=ok:
54612
send: 1-1-0-0 s=0,c=1,t=23,pt=3,l=2,sg=0,st=ok:54612
send: 1-1-0-0 s=255,c=3,t=15,pt=2,l=2,sg=0,st=ok:0
send: 1-1-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,st=ok:1.5.4
send: 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
sensor started, id=1, parent=0, distance=1
send: 1-1-0-0 s=255,c=3,t=11,pt=0,l=16,sg=0,st=ok:Light Lux Sensor
send: 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 1-1-0-0 s=0,c=0,t=16,pt=0,l=0,sg=0,st=ok:
0```

[TheoL]

@the-cosmic-gate Great! And you're also good with a soldering iron. I don't think I could replace an SMD resistor

[the cosmic gate]

@TheoL said:

@the-cosmic-gate Great! And you're also good with a soldering iron. I don't think I could replace an SMD resistor

i didn't solder the SMD just replaced the whole radio much more easy

btw: congratz