Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

help about error in serial monitor

Reza last edited by Reza
hi guys.
please help me about this error in serial monitor.
one:
```
!TSF:MSG:SEND,5-5-0-0,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=10,st=NACK:1
```
two:
```
!TSM:READY:UPL FAIL,SNP
```
three:
```
!TSF:SND:TNR
```
what is related to this error? and what is solution? thank you
Reply Quote 0
1 Reply Last reply
hek Admin last edited by

https://ci.mysensors.org/job/Verifiers/job/MySensors/branch/development/Doxygen_HTML/group__MyTransportgrp.html#details
Reply Quote 1
1 Reply Last reply
Reza last edited by @hek

@hek
thank you dear hek
Reply Quote 1
1 Reply Last reply

3
Posts

556
Views

Log in to reply

Suggested Topics

Day 1 - Status report
Announcements • • hek

3

0
Votes

3
Posts

1519
Views

Feels much faster from here too!
Cannot compile sketch with STM32F1 BluePill board
Troubleshooting • • tnick

5

0
Votes

5
Posts

24
Views

@tnick I know this is an old post, but if it helps you - I've created support for STM32 based on latest STM32duino here. It's currently made to be backward compatible for the existing STM32F1 support, which is what you are struggling. But with a small change you can use the new STM32 HAL support. Let me know if you are interested to give it a try. The longer term plan is to remove the existing (old) STM32F1 support in favor of the new and more general STM32 support. (If @mfalkvidd agrees ;-))
JSN SR04T - Temperature Influencing Readings
Troubleshooting • ultrasonic water level tank • • Timbergetter

34

1
Votes

34
Posts

1377
Views

I'm having the same / a simular issue of temperature related readings, but at a different temperature level (for me it must be > 14 degree). I massure the dew point as well (temperature = orange, dew point = yellow). It looks to be more related to water in the air than only to temperature. @zboblamont have you been finally been able to find a solution?
What are the pin numbers for D3, D4, ...
Troubleshooting • digitalwrite digital io pin numbers • • Bens

8

0
Votes

8
Posts

1829
Views

@Vuinne-Ryvmar You seem to be confused about what this forum is. Maybe you just ended up here on a random Google search? But in our case on an Arduino, D3 is literally the name for one of the metal legs coming off of the little controller, and we call it a pin sometimes. @tbowmo was looking for how to send the command to turn the power on or off to that part of the board, not a code to enable connecting up a controller to their phone. I see that a D3 game controller is a thing, but I doubt you will have any luck getting help with that here. It's not what this site is about. This is what we work with:
HW-488 infrared sensor not detecting properly
Troubleshooting • • jaydenlord

2

0
Votes

2
Posts

11
Views

@jaydenlord Probably you do. If you leave the EN floating, electrical noise could cause it to enable or disable randomly. Some enable pin require a HIGH, some LOW. Connect it to VCC to see if it works more consistently. If it doesn't detect, connect it to GND. If one of these works, then the part wasn't designed to be in a default state of enable. Let us know your results (I found this video OSD
Flame Sensor Not Triggering Setup
Troubleshooting • • Jordan22xx

3

0
Votes

3
Posts

11
Views

You write "...clicking is heard..." Is that a single click or a click click click ...? After getting the LOW signal, wait a period of time and if it's still low, send the message that there is a flame. Likewise for a HIGH signal. Perhaps instead of a relay, an opto-isolator?

15
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1