what is related this error ?

Reza

hi
what is related this errors?

0 MCO:BGN:INIT REPEATER,CP=RNNRA--,VER=2.0.1-beta
4 MCO:BGN:BFR
PRESERVE_RELAY_STATE: NO
Setting relay 1 on pin 3 to state: 0
Setting relay 2 on pin 4 to state: 0
Setting relay 3 on pin 5 to state: 0
Setting relay 4 on pin 6 to state: 0
Setting relay 5 on pin 7 to state: 0
Setting relay 6 on pin 8 to state: 0
Setting relay 7 on pin 14 to state: 0
Setting relay 8 on pin 15 to state: 0
Setting relay 9 on pin 16 to state: 0
Setting relay 10 on pin 17 to state: 0
Setting relay 11 on pin 18 to state: 0
Setting relay 12 on pin 19 to state: 0
41 TSM:INIT
54 TSM:INIT:TSP OK
55 TSM:INIT:STATID=160
57 TSF:SID:OK,ID=160
59 TSM:FPAR
96 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2103 !TSM:FPAR:NO REPLY
2105 TSM:FPAR
2141 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4149 !TSM:FPAR:NO REPLY
4151 TSM:FPAR
4187 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6195 !TSM:FPAR:NO REPLY
6197 TSM:FPAR
6233 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
7376 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
7382 TSF:MSG:BC
8241 !TSM:FPAR:FAIL
8242 TSM:FAIL:CNT=1
8244 TSM:FAIL:PDT
18247 TSM:FAIL:RE-INIT
18249 TSM:INIT
18256 TSM:INIT:TSP OK
18258 TSM:INIT:STATID=160
18260 TSF:SID:OK,ID=160
18263 TSM:FPAR
18299 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
20308 !TSM:FPAR:NO REPLY
20311 TSM:FPAR
20347 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
22355 !TSM:FPAR:NO REPLY
22358 TSM:FPAR
22394 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
24402 !TSM:FPAR:NO REPLY
24404 TSM:FPAR
24441 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
25563 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
25568 TSF:MSG:BC
26449 !TSM:FPAR:FAIL
26450 TSM:FAIL:CNT=2
26452 TSM:FAIL:PDT
36456 TSM:FAIL:RE-INIT
36458 TSM:INIT
36465 TSM:INIT:TSP OK
36467 TSM:INIT:STATID=160
36469 TSF:SID:OK,ID=160
36471 TSM:FPAR
36508 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
38516 !TSM:FPAR:NO REPLY
38518 TSM:FPAR
38555 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
40562 !TSM:FPAR:NO REPLY
40564 TSM:FPAR
40601 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
42608 !TSM:FPAR:NO REPLY
42610 TSM:FPAR
42647 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
44654 !TSM:FPAR:FAIL
44655 TSM:FAIL:CNT=3
44657 TSM:FAIL:PDT
54660 TSM:FAIL:RE-INIT
54662 TSM:INIT
54669 TSM:INIT:TSP OK
54671 TSM:INIT:STATID=160
54673 TSF:SID:OK,ID=160
54675 TSM:FPAR
54712 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
56720 !TSM:FPAR:NO REPLY
56722 TSM:FPAR
56759 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
58766 !TSM:FPAR:NO REPLY
58768 TSM:FPAR
58805 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
60812 !TSM:FPAR:NO REPLY
60814 TSM:FPAR
60851 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
61939 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
61944 TSF:MSG:BC
62858 !TSM:FPAR:FAIL
62859 TSM:FAIL:CNT=4
62861 TSM:FAIL:PDT
72864 TSM:FAIL:RE-INIT
72866 TSM:INIT
72873 TSM:INIT:TSP OK
72876 TSM:INIT:STATID=160
72878 TSF:SID:OK,ID=160
72880 TSM:FPAR
72916 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
74925 !TSM:FPAR:NO REPLY
74927 TSM:FPAR
74963 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
76971 !TSM:FPAR:NO REPLY
76973 TSM:FPAR
77009 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
79017 !TSM:FPAR:NO REPLY
79020 TSM:FPAR
79056 TSF:MSG:SEND,160-160-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
80124 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
80130 TSF:MSG:BC
81064 !TSM:FPAR:FAIL
81065 TSM:FAIL:CNT=5
81068 TSM:FAIL:PDT

martinhjelmare

The node tries to find a parent within the network but gets no reply. Radio/range problems? Follow the troubleshooting flowchart here:
https://forum.mysensors.org/topic/666/debug-faq-and-how-ask-for-help

Reza

@martinhjelmare

i see this. but i can not found my problem ! i have this error but my device is near(1 meter) gateway and dont need search parent i change gateway. change radio , arduino , wire etc... but i have this problem yet

martinhjelmare

What does the corresponding log from the gateway look like? Does it receive, respond and send ok when the node sends the find parent message? Looking at both ends of the conversation usually helps determining at which end the problem might be.

Reza

@martinhjelmare
most node first can not connect to gateway.similar to error in up.but some node connect hardly but after connect, in serial monitor , most of command is NACK.
i have not this problem with sensors. this problem is just related to relays. power of node is ok (also i test this with a 5v 10A power supply. but power of gateway is from orangepi board.
this is complicate for me. sensors is ok and report all states but relays... perhaps is related my sketchs. i dont know :(

Reza

@martinhjelmare
i think this is related to power of gateway! because sensors just report to gateway and gateway dont send any command, so work well. but for relay, gateway want send command and ack... so have problem , i dont know i am confuse:(

martinhjelmare

You could be on to something. Although the gateway will still have to send some things to sensors, like parent reply etc. If you want more input I suggest you record logs of both gateway and a node in parallel, and post it here.

Previously there's been reports of the gateway performing better with two capacitors in parallel with the radio instead of the regular one capacitor, or a higher value on the capacitor compared to nodes.

Reza

@martinhjelmare
thank you, i want put a capacitor for serial gateway. where i put capacitor ? serial gateway is connect to controller with a usb cable , now where i put capacitor?

martinhjelmare

I was referring to the recommended decoupling capacitor for the radio. This is described here:
https://www.mysensors.org/build/connect_radio#connecting-a-decoupling-capacitor

Next step would be to try to change the power source for the arduino and/or radio entirely.
This page has several important points at the top about power:
https://www.mysensors.org/build/debug

These are some questions that might be important:
You said you're powering the gateway from an OrangePi. How are you powering the OrangePi? Do you know the power specs of the USB ports on your OrangePi? How have you built your gateway, and what power does it require? Particularly, what radio module is the gateway using, amplified or non-amplified?

Reza

@martinhjelmare
i test all of state for gateway and nodes. states:
serial gateway and relay nodes + usual radio
serial gateway and relay nodes + usual radio + 4.7u and 100u capacitor
serial gateway and relay nodes + nRF24L01+PA+LNA with antenna
serial gateway and relay nodes + nRF24L01+PA+LNA with antenna + 4.7u and 100 capacitor
serial gateway and relay nodes + usual radio + adapter radio
serial gateway and relay nodes + nRF24L01+PA+LNA with antenna + adapter radio
i am tired really:( now i think power of gateway is weak.(power of nodes is ok and i test it) but power of serial gate way is with usb from orangepi. this is orangepi one and have one port usb and i use this for serial gateway. i dont know how i see power of usb port! but i think most of error is NACK so gateway can not work well. so i want from you to help for capacitor for input arduino , no input radio. i test all of state input for radio....
power of orange pi is 5v 2A.
thank you

martinhjelmare

@Reza

You seem to be getting help with the same problem in the other thread, so I'll stop here.

what is related this error ?

15

11.7k

11.2k

113.1k