Sleep function breaks code

martins

Re: [ Door](Window and Push-button Sensor)

As soon as I use the sleep function with this door-sensor-code it breaks it. Works awhile and then gone.

sleep(PRIMARY_BUTTON_PIN-2, CHANGE, 0);

Serial output:
!TSM:UPL FAIL, SNP
TSM:FPAR
TSP:MSG:SEND 2-2-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR

And there it dies ! Any suggestions?

Thanks,
Martin

mfalkvidd

@martins which Arduino are you using? Which pin are you using? Which sketch are you using? (I am unable to find a sketch that references PRIMARY_BUTTON_PIN, searched through the code for the library and the MySensorsArduinoExamples reporistory). How are you powering the sensor?

There have been some threads about problems with CHANGE:
https://forum.mysensors.org/topic/5552/pin-change-interrupt-not-firing-with-mysensors/
https://forum.mysensors.org/topic/5807/interrupt-and-sleep/

martins

Thanks. I'm trying these 2 but both givers the same results:

/**

The MySensors Arduino library handles the wireless radio link and protocol
between your home built sensors/actuators and HA controller of choice.
The sensors forms a self healing radio network with optional repeaters. Each
repeater and gateway builds a routing tables in EEPROM which keeps track of the
network topology allowing messages to be routed to nodes.
Created by Henrik Ekblad henrik.ekblad@mysensors.org
Copyright (C) 2013-2015 Sensnology AB
Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
Documentation: http://www.mysensors.org
Support Forum: http://forum.mysensors.org
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.

DESCRIPTION
Simple binary switch example
Connect button or door/window reed switch between
digitial I/O pin 3 (BUTTON_PIN below) and GND.
http://www.mysensors.org/build/binary
*/

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
// #define MY_RADIO_NRF24
#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_433MHZ
#define MY_IS_RFM69HW

#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define CHILD_ID 3
#define BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

Bounce debouncer = Bounce();
int oldValue=-1;
int BATTERY_SENSE_PIN = A0; // select the input pin for the battery sense point

unsigned long SLEEP_TIME = 60000; // sleep time between reads (seconds * 1000 milliseconds)
int oldBatteryPcnt = 0;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_TRIPPED);

void setup()
{
// use the 1.1 V internal reference
#if defined(AVR_ATmega2560)
analogReference(INTERNAL1V1);
#else
analogReference(INTERNAL);
#endif

// Setup the button
pinMode(BUTTON_PIN,INPUT);
// Activate internal pull-up
digitalWrite(BUTTON_PIN,HIGH);

// After setting up the button, setup debouncer
debouncer.attach(BUTTON_PIN);
debouncer.interval(5);

}

void presentation() {
// Register binary input sensor to gw (they will be created as child devices)
// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
// If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
present(CHILD_ID, S_DOOR);
// Send the sketch version information to the gateway and Controller
sendSketchInfo("Door Sensor", "1.0");
}

// Check if digital input has changed and send in new value
void loop()
{
debouncer.update();
// Get the update value
int value = debouncer.read();

if (value != oldValue) {
// Send in the new value
send(msg.set(value==HIGH ? 1 : 0));
oldValue = value;

     // get the battery Voltage
int sensorValue = analogRead(BATTERY_SENSE_PIN);

#ifdef MY_DEBUG
Serial.println(sensorValue);
#endif

// 1M, 470K divider across battery and using internal ADC ref of 1.1V
// Sense point is bypassed with 0.1 uF cap to reduce noise at that point
// ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
// 3.44/1023 = Volts per bit = 0.003363075

int batteryPcnt = sensorValue / 10;

#ifdef MY_DEBUG
float batteryV = sensorValue * 0.003363075;
Serial.print("Battery Voltage: ");
Serial.print(batteryV);
Serial.println(" V");

Serial.print("Battery percent: ");
Serial.print(batteryPcnt);
Serial.println(" %");

#endif

if (oldBatteryPcnt != batteryPcnt) {
// Power up radio after sleep
sendBatteryLevel(batteryPcnt);
oldBatteryPcnt = batteryPcnt;
}
// sleep(SLEEP_TIME);
sleep(BUTTON_PIN-2, CHANGE, SLEEP_TIME);
}
}

/**

The MySensors Arduino library handles the wireless radio link and protocol
between your home built sensors/actuators and HA controller of choice.
The sensors forms a self healing radio network with optional repeaters. Each
repeater and gateway builds a routing tables in EEPROM which keeps track of the
network topology allowing messages to be routed to nodes.
Created by Henrik Ekblad henrik.ekblad@mysensors.org
Copyright (C) 2013-2015 Sensnology AB
Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
Documentation: http://www.mysensors.org
Support Forum: http://forum.mysensors.org
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.

DESCRIPTION
Interrupt driven binary switch example with dual interrupts
Author: Patrick 'Anticimex' Fallberg
Connect one button or door/window reed switch between
digitial I/O pin 3 (BUTTON_PIN below) and GND and the other
one in similar fashion on digital I/O pin 2.
This example is designed to fit Arduino Nano/Pro Mini

*/

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_433MHZ
#define MY_IS_RFM69HW

#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

#include <SPI.h>
#include <MySensors.h>

#define BATTERY_SENSE_PIN A0

#define SKETCH_NAME "Binary Sensor"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
//#define SECONDARY_CHILD_ID 4

unsigned long SLEEP_TIME = 60000; // sleep time between reads (seconds * 1000 milliseconds)

#define PRIMARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch
//#define SECONDARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

#if (PRIMARY_BUTTON_PIN < 2 || PRIMARY_BUTTON_PIN > 3)
#error PRIMARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
//#if (SECONDARY_BUTTON_PIN < 2 || SECONDARY_BUTTON_PIN > 3)
//#error SECONDARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
//#endif
//#if (PRIMARY_BUTTON_PIN == SECONDARY_BUTTON_PIN)
//#error PRIMARY_BUTTON_PIN and BUTTON_PIN2 cannot be the same
//#endif
//#if (PRIMARY_CHILD_ID == SECONDARY_CHILD_ID)
//#error PRIMARY_CHILD_ID and SECONDARY_CHILD_ID cannot be the same
//#endif

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);
//MyMessage msg2(SECONDARY_CHILD_ID, V_TRIPPED);

void setup()
{
// Setup the buttons
pinMode(PRIMARY_BUTTON_PIN, INPUT);
// pinMode(SECONDARY_BUTTON_PIN, INPUT);

// Activate internal pull-ups
digitalWrite(PRIMARY_BUTTON_PIN, HIGH);
// digitalWrite(SECONDARY_BUTTON_PIN, HIGH);

}

void presentation() {
// Send the sketch version information to the gateway and Controller
sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER "." SKETCH_MINOR_VER);

// Register binary input sensor to sensor_node (they will be created as child devices)
// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
// If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
present(PRIMARY_CHILD_ID, S_DOOR);
// present(SECONDARY_CHILD_ID, S_DOOR);
}

// Loop will iterate on changes on the BUTTON_PINs
void loop()
{
uint8_t value;
static uint8_t sentValue=2;
//static uint8_t sentValue2=2;
//attachInterrupt(0, wakeUp, LOW);
// Short delay to allow buttons to properly settle
//sleep(5);

value = digitalRead(PRIMARY_BUTTON_PIN);

if (value != sentValue) {
// Value has changed from last transmission, send the updated value
send(msg.set(value==HIGH ? 1 : 0));
sentValue = value;
}

// value = digitalRead(SECONDARY_BUTTON_PIN);

// if (value != sentValue2) {
// // Value has changed from last transmission, send the updated value
// send(msg2.set(value==HIGH ? 1 : 0));
// sentValue2 = value;
// }

// Sleep until something happens with the sensor
sleep(PRIMARY_BUTTON_PIN-2, CHANGE, SLEEP_TIME);
delay(2000);
value = digitalRead(PRIMARY_BUTTON_PIN);
}

Regards,
Martin

martins

@mfalkvidd

It's almost as if the RFM69 radio is not transmitting anymore:
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR
!TSP:SEND:TNR

What does TNR mean ? Transmitter Not Ready ? I looked through the serial API but can't find any reference. Neither in the sensor API nor library API. Any suggestions ?

Thanks,
Martin

DavidZH

first of all you should change the delay(2000) right after the sleep to wait(2000). Effect is exactly the same, but this will not stop your Arduino from doing anything. For the rest I'm not sure why the communication between your Arduino and radio stops. TNR is indeed "Transport not ready"...

martins

OK it's working. Main fix I think is I used the new 2.1.1 library and all comms to the RFM69 radio seems to be fixed.

Current code:

DESCRIPTION
Simple binary switch example
Connect button or door/window reed switch between
digitial I/O pin 3 (BUTTON_PIN below) and GND.
http://www.mysensors.org/build/binary
*/

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
// #define MY_RADIO_NRF24
#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_433MHZ
#define MY_IS_RFM69HW

#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

#include <SPI.h>
#include <MySensors.h>

#define CHILD_ID 3
#define BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

int oldValue=-1;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_TRIPPED);

void setup()
{
// Setup the button
pinMode(BUTTON_PIN,INPUT);
// Activate internal pull-up
digitalWrite(BUTTON_PIN,HIGH);
}

void presentation() {
// Register binary input sensor to gw (they will be created as child devices)
sendSketchInfo("Binary Sensor", "1.0");
// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
// If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
present(CHILD_ID, S_DOOR);
// Send the sketch version information to the gateway and Controller
}

// Check if digital input has changed and send in new value
void loop()
{
int value = digitalRead(BUTTON_PIN);
#ifdef MY_DEBUG
Serial.println("Sensor Value");
Serial.println(value);
#endif
send(msg.set(value==HIGH ? 1 : 0));
sleep(BUTTON_PIN-2, CHANGE, 0);
}

Thanks,
Martin

Sleep function breaks code

Suggested Topics

Day 1 - Status report
Announcements • • hek

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA)
Troubleshooting • • se-O-matic

Echo request is not set
Troubleshooting • • kamilb85

Extraneous info in Debug log
Troubleshooting • debug log • • Gibber

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Sleep function breaks code

Suggested Topics

Day 1 - Status report Announcements • • hek

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA) Troubleshooting • • se-O-matic

Echo request is not set Troubleshooting • • kamilb85

Extraneous info in Debug log Troubleshooting • debug log • • Gibber

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Day 1 - Status report
Announcements • • hek

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA)
Troubleshooting • • se-O-matic

Echo request is not set
Troubleshooting • • kamilb85

Extraneous info in Debug log
Troubleshooting • debug log • • Gibber

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts