Domoticz - soil moisture + one relay = Lua script error (Blockly)

[k5austria]

This post is deleted!

[gohan]

#define CHILD_ID 0 change to CHILD_ID_MOISTURE

[k5austria]

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
#define CHILD_ID_MOISTURE 0

#include <MySensors.h>
// Here we are setting up some water thresholds that we will
// use later. Note that you will need to change these to match
// your soil type and environment. It doesn't do much for me because I'm using domoticz
int thresholdUp = 400;
int thresholdDown = 075;
MyMessage msg(CHILD_ID_MOISTURE, S_HUM);
unsigned long SLEEP_TIME = 30000;

// We are setting up the pin A0 on the redboard to be our sensor
// pin input:
int sensorPin = A0;

void presentation()
{
present(CHILD_ID_MOISTURE, S_HUM);
}

void loop()
{
int sensorValue;
sensorValue = analogRead(sensorPin);

//send back the values
send(msg.set(sensorValue));
// delay until next measurement (msec)
sleep(SLEEP_TIME);
}

[k5austria]

This post is deleted!

[gohan]

#define CHILD_ID_MOISTURE 0

You always need to specify a value

[k5austria]

This post is deleted!

[gohan]

5th row of your code

[k5austria]

This post is deleted!

[k5austria]

This post is deleted!

[k5austria]

This post is deleted!

[k5austria]

Sensor logs on to Gateway only with original sketch. Other sketchs can be quite normal uploaded to Arduino but remains for GW invisible.

[gohan]

Pls post node serial output when not connecting to the gateway

[k5austria]

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSF:SID:OK,ID=2
14 TSM:FPAR
51 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
775 TSF:MSG:READ,0-0-2,s=255,c=3,t=8,pt=1,l=1,sg=0:0
780 TSF:MSG:FPAR OK,ID=0,D=1
2058 TSM:FPAR:OK
2059 TSM:ID
2060 TSM:ID:OK
2062 TSM:UPL
2065 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2074 TSF:MSG:READ,0-0-2,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2079 TSF:MSG:PONG RECV,HP=1
2081 TSM:UPL:OK
2083 TSM:READY:ID=2,PAR=0,DIS=1
2087 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2095 TSF:MSG:READ,0-0-2,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2102 TSF:MSG:SEND,2-2-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
2110 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2123 TSF:MSG:READ,0-0-2,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2132 TSF:MSG:SEND,2-2-0-0,s=0,c=0,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2139 MCO:REG:REQ
2146 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2152 TSF:MSG:READ,0-0-2,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2157 MCO:PIM:NODE REG=1
2160 MCO:BGN:INIT OK,TSP=1
2168 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=2,l=2,sg=0,ft=0,st=OK:413
2174 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
2180 MCO:SLP:TPD
2182 MCO:SLP:WUP=-1
2189 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=2,l=2,sg=0,ft=0,st=OK:412
2195 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
2200 MCO:SLP:TPD
2202 MCO:SLP:WUP=-1
2209 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=2,l=2,sg=0,ft=0,st=OK:412
2214 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
2220 MCO:SLP:TPD

[gohan]

Check yourself in the log parser page https://www.mysensors.org/build/parser

Your node is connected to gateway and reporting the values (look at the 413 - 412 -412 that were sent).
Also please use the Code TAG when posting code or logs as it makes it more readable.

[k5austria]

Ok ! Sorry !

After several reset from raspberry is the sensor visible by Domoticz, but is not in device list.