3. [solved] RPI Gateway with RFM95 does not receive any nodes

[solved] RPI Gateway with RFM95 does not receive any nodes

  • micropet

    Hello,

    have built many gateways with an RPI2 and the RFM96. All work well. Now I wanted to test an RFM95 gateway.
    The software compiles and starts properly.
    My 3 RFM95 Nodes get but no connection.

    Has anyone ever run an RPI gateway with RFM95?

    Info: I have compiled the Gateway with:

    .myconfigure --my-gateway = mqtt --my-controller-ip-address = 192.168.0.23 --my-mqtt-publish-topic-prefix = mysensors2-out --my-mqtt-subscribe-topic-prefix = I have the same problem with mymy-leds -my-leds-err-pin = 12 - my-leds-rx-pin = 16 --my-leds-tx -pin = 18

    The wiring:

    Raspberry RFM69
    GND GND
    3.3V VCC
    24 NSS
    23 SCK
    19 MOSI
    21 MISO
    22 DI00

    Gateway starts successfully but does not receive anything.

    The hardware is fine. The gateway and the node run with the LowCost gateway:
    http://cpham.perso.univ-pau.fr/LORA/RPIgateway.html

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    Adding link to the github issue, in case the information there helps anyone: https://github.com/mysensors/MySensors/issues/863

    0
  • mfalkvidd
    Mod

    @micropet Since no-one else seems to be able to help, I have dug out an old raspberry pi and started to retrace your steps. It is going slow, but forwards.

    One thing I notice is that the configure command above does not include --my-transport=rfm95

    Just a quick check - was rfm95 included in your configure command?

    Also, could you post the debug output from the gateway?

    I realize that you might have given up, but I hope to be able to check that rfm95 works.

    0
  • mfalkvidd
    Mod

    I now have the gateway up and running, at least it seems so:

    pi@raspi1:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Config file /etc/mysensors.dat does not exist, creating new config file.
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

    Parsed log

    Next step is to build a rfm95 node.

    EDIT: My configure command:

    ./configure --my-transport=rfm95
    0
  • mfalkvidd
    Mod

    My test node (a binary switch that toggles state every 2 seconds) is able to communicate with the gateway.

    Gateway log:

    mysgw: Config file /etc/mysensors.dat does not exist, creating new config file.
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:SAN:OK
mysgw: TSM:READY:NWD REQ
mysgw: TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
mysgw: TSF:SRT:OK
mysgw: TSF:SAN:OK
mysgw: TSF:MSG:READ,102-102-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=102
mysgw: TSF:PNG:SEND,TO=0
mysgw: TSF:CKU:OK
mysgw: TSF:MSG:GWL OK
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:PINGED,ID=102,HP=1
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
mysgw: TSF:MSG:READ,102-102-0,s=255,c=0,t=17,pt=0,l=10,sg=0:2.2.0-beta
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=11,pt=0,l=13,sg=0:Binary Sensor
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=0,t=0,pt=0,l=0,sg=0:
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1

    Node log:

    5134 MCO:BGN:INIT NODE,CP=RLNNE---,VER=2.2.0-beta
5176 TSM:INIT
5177 TSF:WUR:MS=0
5194 TSM:INIT:TSP OK
5196 TSF:SID:OK,ID=102
5198 TSM:FPAR
5248 TSF:MSG:SEND,102-102-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
5881 TSF:MSG:READ,0-0-102,s=255,c=3,t=8,pt=1,l=1,sg=0:0
5886 TSF:MSG:FPAR OK,ID=0,D=1
7255 TSM:FPAR:OK
7256 TSM:ID
7257 TSM:ID:OK
7258 TSM:UPL
7363 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
7414 TSF:MSG:READ,0-0-102,s=255,c=3,t=25,pt=1,l=1,sg=0:1
7419 TSF:MSG:PONG RECV,HP=1
7422 TSM:UPL:OK
7423 TSM:READY:ID=102,PAR=0,DIS=1
7558 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
7609 TSF:MSG:READ,0-0-102,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
7764 TSF:MSG:SEND,102-102-0-0,s=255,c=0,t=17,pt=0,l=10,sg=0,ft=0,st=OK:2.2.0-beta
7865 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
9990 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=11,pt=0,l=13,sg=0,ft=0,st=OK:Binary Sensor
10102 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
10203 TSF:MSG:SEND,102-102-0-0,s=3,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK:
10209 MCO:REG:REQ
10305 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
10356 TSF:MSG:READ,0-0-102,s=255,c=3,t=27,pt=1,l=1,sg=0:1
10361 MCO:PIM:NODE REG=1
10363 MCO:BGN:STP
10365 MCO:BGN:INIT OK,TSP=1
10501 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
12614 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
14728 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
16833 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
18938 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
21052 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
23158 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
25272 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
    0
  • micropet

    Thanks for testing.

    Transport word in it. The line was something mixed up here in the forum. 🙂

    ./configure --my-gateway=mqtt --my-controller-ip-address=192.168.0.23 --my-mqtt-publish-topic-prefix=mysensors2-out --my-mqtt-subscribe-topic-prefix=mysensors2-in --my-mqtt-client-id=mygateway5 --my-transport=rfm95 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18

    The Gateway shows:

    ./bin/mysgw -d
    mysgw: Starting gateway...
    mysgw: Protocol version - 2.2.0-beta
    mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
    mysgw: TSF:LRT:OK
    mysgw: TSM:INIT
    mysgw: TSF:WUR:MS=0
    mysgw: TSM:INIT:TSP OK
    mysgw: TSM:INIT:GW MODE
    mysgw: TSM:READY:ID=0,PAR=0,DIS=0
    mysgw: MCO:REG:NOT NEEDED
    mysgw: MCO:BGN:STP
    mysgw: MCO:BGN:INIT OK,TSP=1
    mysgw: Attempting MQTT connection...
    mysgw: connected to 192.168.0.23
    mysgw: MQTT connected
    mysgw: Sending message on topic: mysensors2-out/0/255/0/0/18

    I have to look for a MySensor Node.
    I had changed everything to the TTN network.

    I'll get back to you.

    Greetings Peter

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @micropet great. The problem might be mqtt related. I am not sure if I have a mqtt broker to connect to so I just tried the ethernet variant. Could you see if switching to ethernet helps? That would narrow down the scope.

    0
  • micropet

    Thus, the node is in operation. The gateway does not show anything new.

    I need mqtt. My RFM69 Nodes (433 MHz and 868 MHz) also run with mqtt.

    The Node output is:

    0 MCO:BGN:INIT NODE,CP=RLNNA---,VER=2.2.0-beta
    4 TSM:INIT
    4 TSF:WUR:MS=0
    6 RFM95:INIT
    8 RFM95:INIT:PIN,CS=10,IQP=4,IQN=0
    22 RFM95:PTX:LEVEL=5
    24 TSM:INIT:TSP OK
    26 TSM:INIT:STATID=150
    28 TSF:SID:OK,ID=150
    30 TSM:FPAR
    32 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
    2037 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    4046 !TSM:FPAR:NO REPLY
    4048 TSM:FPAR
    4050 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
    6057 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    8067 !TSM:FPAR:NO REPLY
    8069 TSM:FPAR
    8071 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
    10076 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    12085 !TSM:FPAR:NO REPLY
    12087 TSM:FPAR
    12089 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
    14094 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    16103 !TSM:FPAR:FAIL
    16105 TSM:FAIL:CNT=1
    16107 TSM:FAIL:DIS
    16109 TSF:TDI:TSL
    16111 RFM95:RSL
    26114 TSM:FAIL:RE-INIT
    26116 TSM:INIT
    26118 RFM95:INIT
    26120 RFM95:INIT:PIN,CS=10,IQP=4,IQN=0
    26134 RFM95:PTX:LEVEL=5
    26136 TSM:INIT:TSP OK
    26138 TSM:INIT:STATID=150
    26140 TSF:SID:OK,ID=150
    26144 TSM:FPAR
    26146 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
    28151 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    30162 !TSM:FPAR:NO REPLY
    30164 TSM:FPAR
    30167 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
    32172 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @micropet I understand you prefer mqtt. But if you are able to verify that the gateway works with ethernet, we would know that the problem is mqtt related. Now the problem might be related to anything.

    0
  • micropet

    Yes I understand.
    I'm just checking the pin assignment of the node.
    How did you connect the Node to the RFM95?

    0 mfalkvidd 1 Reply
  • micropet

    I use the same connections as for a TTN node.

    Board is Arduino Pro mini.

    10 NSS CS
    13 SCK
    11 MOSI
    12 MISO

    4 DI00
    5 DIO1

    And have in the sketch:

    #define MY_RFM95_CS_PIN 10 // NSS
    #define MY_RFM95_IRQ_PIN 4 // IRQ D100

    0
  • mfalkvidd
    Mod

    @micropet mqtt works:

    pi@raspi1:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.1.101
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors-rfm95-out/0/255/0/0/18
mysgw: TSF:MSG:READ,102-102-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=102
mysgw: TSF:PNG:SEND,TO=0
mysgw: TSF:CKU:OK
mysgw: TSF:MSG:GWL OK
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:PINGED,ID=102,HP=1
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
mysgw: TSF:MSG:READ,102-102-0,s=255,c=0,t=17,pt=0,l=10,sg=0:2.2.0-beta
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/0/0/17
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/3/0/6
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=11,pt=0,l=13,sg=0:Binary Sensor
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/3/0/11
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/3/0/12
mysgw: TSF:MSG:READ,102-102-0,s=3,c=0,t=0,pt=0,l=0,sg=0:
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/0/0/0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16

    I used this configure command:

    ./configure --my-gateway=mqtt --my-controller-ip-address=192.168.1.101 --my-mqtt-publish-topic-prefix=mysensors-rfm95-out --my-mqtt-subscribe-topic-prefix=mysensors-rfm95-in --my-mqtt-client-id=mygateway-rfm95 --my-transport=rfm95 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18

    For the wiring, I used the instructions for rfm69 on the raspberry pi gateway page.

    0
  • mfalkvidd
    Mod

    For the node, I used this sketch (esp8266 nodemcu):

    // Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM95

#define MY_RFM95_CS_PIN D8 // NSS
#define MY_RFM95_IRQ_PIN D1 // IRQ DIO0
#define MY_RFM95_RST_PIN D3 // Reset, not connected


#include <MySensors.h>

#define SKETCH_NAME "Binary Sensor"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
#define SECONDARY_CHILD_ID 4

#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch
#define SECONDARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

#if (PRIMARY_BUTTON_PIN < 2 || PRIMARY_BUTTON_PIN > 3)
#error PRIMARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (SECONDARY_BUTTON_PIN < 2 || SECONDARY_BUTTON_PIN > 3)
#error SECONDARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (PRIMARY_BUTTON_PIN == SECONDARY_BUTTON_PIN)
#error PRIMARY_BUTTON_PIN and BUTTON_PIN2 cannot be the same
#endif
#if (PRIMARY_CHILD_ID == SECONDARY_CHILD_ID)
#error PRIMARY_CHILD_ID and SECONDARY_CHILD_ID cannot be the same
#endif


// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);

void setup()
{

}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER "." SKETCH_MINOR_VER);

  // Register binary input sensor to sensor_node (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  present(PRIMARY_CHILD_ID, S_DOOR);
}

// Loop will iterate on changes on the BUTTON_PINs
void loop()
{
  static uint8_t sentValue = 2;

  // Short delay to allow buttons to properly settle
  wait(5);

  uint8_t  value = !sentValue;

  if (value != sentValue) {
    // Value has changed from last transmission, send the updated value
    send(msg.set(value == HIGH));
    sentValue = value;
  }

  wait(2000);
}
    0
  • micropet

    My gateway will work, I think.

    Pity,

    I am using an Arduino Pro mini.
    I can make a node with esp8266.
    But I can not do that today, I think I have time for it tomorrow.

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @micropet no rush, you've had to wait a long time to get any help 😉
    Just post here when/if you have some news. If you are unable to find an esp I can probably find a Pro Mini and build a node.

    0
  • micropet

    Have a node with a NodeMCU built.
    Does not work either.
    At the gateway comes nothing.
    Since I must look further.

    22820 !TSM:FPAR:NO REPLY
    22822 TSM:FPAR
    24824 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    26831 !TSM:FPAR:NO REPLY
    26833 TSM:FPAR
    28835 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    30842 !TSM:FPAR:NO REPLY
    30844 TSM:FPAR
    32846 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    34853 !TSM:FPAR:FAIL
    34854 TSM:FAIL:CNT=1
    34856 TSM:FAIL:DIS
    34858 TSF:TDI:TSL
    44860 TSM:FAIL:RE-INIT
    44861 TSM:INIT
    44878 TSM:INIT:TSP OK
    44880 TSF:SID:OK,ID=33
    44882 TSM:FPAR
    46885 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    48892 !TSM:FPAR:NO REPLY
    48894 TSM:FPAR
    50896 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    52903 !TSM:FPAR:NO REPLY
    52905 TSM:FPAR
    54907 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    56914 !TSM:FPAR:NO REPLY
    56916 TSM:FPAR
    58918 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    60925 !TSM:FPAR:FAIL
    60926 TSM:FAIL:CNT=2
    60928 TSM:FAIL:DIS
    60930 TSF:TDI:TSL

    0
  • micropet

    A Node with a Pro mini or a Teensy would help me more.

    All my RFM69 Nodes have a Pro mini (50 pcs)
    The TTN Nodes a Pro mini or a Teensy. (Approx. 20 pieces)

    0
  • micropet

    Now I do not understand anything anymore.

    I have made an update on the RPI and compiled the gateway software again.
    I had already done more than 10 times.
    After the start of the RPI nothing worked.
    Multiple resets of the NodeMCU also brought nothing.

    I pulled the micro usb plug and plugged again - suddenly it works. WAU

    Then I must have a fault in the wiring between the RFM95 and the Arduino Pro.
      Just for info: I had set up 5 pieces. All do not work.

    ./bin/mysgw -d
    mysgw: Starting gateway...
    mysgw: Protocol version - 2.2.0-beta
    mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
    mysgw: TSF:LRT:OK
    mysgw: TSM:INIT
    mysgw: TSF:WUR:MS=0
    mysgw: TSM:INIT:TSP OK
    mysgw: TSM:INIT:GW MODE
    mysgw: TSM:READY:ID=0,PAR=0,DIS=0
    mysgw: MCO:REG:NOT NEEDED
    mysgw: MCO:BGN:STP
    mysgw: MCO:BGN:INIT OK,TSP=1
    mysgw: Attempting MQTT connection...
    mysgw: connected to 192.168.0.23
    mysgw: MQTT connected
    mysgw: Sending message on topic: mysensors2-out/0/255/0/0/18
    mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
    mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
    mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
    mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
    mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
    mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
    mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
    mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
    mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
    mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16

    0
  • micropet

    Hi,

    I have connected my Arduino Pro Nodes. They do not work.
    The ESP Node has been running since last night without problems.

    Can you try an Arduino?

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @micropet great work. I should be able to set up an Arduino node tomorrow. The forecast shows rain anyway 🙂

    0
  • micropet

    Fine.

    I'm just trying a Teensy LC Node.
    See you tomorrow.

    Here in Essen, Germany, it should also rain. 🙂

    0
  • micropet

    The Teensy LC also works.

    So the problem is the Arduino Pro mini.

    1 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @micropet I'm unfortunately not able to reproduce the problem. This is the output of my Pro Mini 3.3V node:

    0 MCO:BGN:INIT NODE,CP=RLNNA---,VER=2.2.0-beta
4 TSM:INIT
4 TSF:WUR:MS=0
16 TSM:INIT:TSP OK
18 TSF:SID:OK,ID=6
20 TSM:FPAR
71 TSF:MSG:SEND,6-6-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1130 TSF:MSG:READ,0-0-6,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1134 TSF:MSG:FPAR OK,ID=0,D=1
2078 TSM:FPAR:OK
2078 TSM:ID
2080 TSM:ID:OK
2082 TSM:UPL
2183 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2232 TSF:MSG:READ,0-0-6,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2238 TSF:MSG:PONG RECV,HP=1
2242 TSM:UPL:OK
2244 TSM:READY:ID=6,PAR=0,DIS=1
2375 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2426 TSF:MSG:READ,0-0-6,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2578 TSF:MSG:SEND,6-6-0-0,s=255,c=0,t=17,pt=0,l=10,sg=0,ft=0,st=OK:2.2.0-beta
2689 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4814 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=11,pt=0,l=13,sg=0,ft=0,st=OK:Binary Sensor
4925 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
5027 TSF:MSG:SEND,6-6-0-0,s=3,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK:
5036 MCO:REG:REQ
5132 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
5183 TSF:MSG:READ,0-0-6,s=255,c=3,t=27,pt=1,l=1,sg=0:1
5189 MCO:PIM:NODE REG=1
5191 MCO:BGN:STP
5193 MCO:BGN:INIT OK,TSP=1
5326 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
7438 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
9549 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
11661 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
13774 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
15886 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1

    Gateway:

    Jul  8 11:56:14 raspi1 mysgw: TSF:MSG:READ,6-6-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
Jul  8 11:56:14 raspi1 mysgw: TSF:MSG:BC
Jul  8 11:56:14 raspi1 mysgw: TSF:MSG:FPAR REQ,ID=6
Jul  8 11:56:14 raspi1 mysgw: TSF:PNG:SEND,TO=0
Jul  8 11:56:14 raspi1 mysgw: TSF:CKU:OK
Jul  8 11:56:14 raspi1 mysgw: TSF:MSG:GWL OK
Jul  8 11:56:15 raspi1 mysgw: TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
Jul  8 11:56:16 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
Jul  8 11:56:16 raspi1 mysgw: TSF:MSG:PINGED,ID=6,HP=1
Jul  8 11:56:16 raspi1 mysgw: TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
Jul  8 11:56:16 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
Jul  8 11:56:16 raspi1 mysgw: TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
Jul  8 11:56:17 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=0,t=17,pt=0,l=10,sg=0:2.2.0-beta
Jul  8 11:56:17 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/255/0/0/17
Jul  8 11:56:17 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
Jul  8 11:56:17 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/255/3/0/6
Jul  8 11:56:19 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=3,t=11,pt=0,l=13,sg=0:Binary Sensor
Jul  8 11:56:19 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/255/3/0/11
Jul  8 11:56:19 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
Jul  8 11:56:19 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/255/3/0/12
Jul  8 11:56:19 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=0,t=0,pt=0,l=0,sg=0:
Jul  8 11:56:19 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/0/0/0
Jul  8 11:56:19 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
Jul  8 11:56:19 raspi1 mysgw: TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
Jul  8 11:56:19 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
Jul  8 11:56:19 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:21 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
Jul  8 11:56:21 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:24 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
Jul  8 11:56:24 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:26 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
Jul  8 11:56:26 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:28 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
Jul  8 11:56:28 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:30 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
Jul  8 11:56:30 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:32 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
Jul  8 11:56:32 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:34 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
Jul  8 11:56:34 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:36 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
Jul  8 11:56:36 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16
Jul  8 11:56:38 raspi1 mysgw: TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
Jul  8 11:56:38 raspi1 mysgw: Sending message on topic: mysensors-rfm95-out/6/3/1/0/16

    Sketch for the node: (same as for the esp8266 except that I removed the pin defines)

    // Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM95

#include <MySensors.h>

#define SKETCH_NAME "Binary Sensor"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
#define SECONDARY_CHILD_ID 4

#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch
#define SECONDARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

#if (PRIMARY_BUTTON_PIN < 2 || PRIMARY_BUTTON_PIN > 3)
#error PRIMARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (SECONDARY_BUTTON_PIN < 2 || SECONDARY_BUTTON_PIN > 3)
#error SECONDARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (PRIMARY_BUTTON_PIN == SECONDARY_BUTTON_PIN)
#error PRIMARY_BUTTON_PIN and BUTTON_PIN2 cannot be the same
#endif
#if (PRIMARY_CHILD_ID == SECONDARY_CHILD_ID)
#error PRIMARY_CHILD_ID and SECONDARY_CHILD_ID cannot be the same
#endif


// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);

void setup()
{

}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER "." SKETCH_MINOR_VER);

  // Register binary input sensor to sensor_node (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  present(PRIMARY_CHILD_ID, S_DOOR);
}

// Loop will iterate on changes on the BUTTON_PINs
void loop()
{
  static uint8_t sentValue = 2;

  // Short delay to allow buttons to properly settle
  wait(5);

  uint8_t  value = !sentValue;

  if (value != sentValue) {
    // Value has changed from last transmission, send the updated value
    send(msg.set(value == HIGH));
    sentValue = value;
  }

  wait(2000);
}

    Wiring as per https://www.mysensors.org/build/connect_radio#rfm69-&-arduino

    0
  • micropet

    Hi,

    Thank you.
    Now it works.

    The trick is D100 must be on pin 2.

    I try to make the pin assignments the same for all nodes (STM32, Arduino Pro, Teensy LC Tennsy 3.1 / 3.6, ESP8266).

    D100 I had put on pin 6 and
    #define MY_RFM95_IRQ_PIN 6
    In the sketch.

    That was the mistake with the Arduino.
    On all other platforms it works.
     
    Many Thanks. I had already given up.

    1 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @micropet great that you were able to isolate the problem. Thanks for the cooperation during troubleshooting.

    In case you didn't already know, only pin 2 and 3 on Pro Mini can be used for hardware interrupts. See https://www.arduino.cc/en/Main/ArduinoBoardProMini for details.

    0
  • micropet

    I thank you. Now I have come a whole lot further.

    I know that only the pins 2 and 3 are IRQ capable.

    I thought I would have read that the IRQ is not used, but the pin is only polled.

    This is how it is done with the LMIC Lib at The Things Network.

    I have still determined when I use the following at the Arduino:
    #define MY_RFM95_RST_PIN 4
    The Arduino does not send anything.
    It works with Teensy or ESP.

    The sleep mode with the teensy does also not always work.
    Sometimes he freezes.

    I will continue tomorrow....

    0
  • micropet

    For information on electricity consumption:

    Tensy 3.2 mit RFM96HW 130 µA
    Tensy 3.2 mit RFM96HW BME280 130 µA
    Tensy 3.2 mit RFM96HW BME280 BH1750 165 µA
    Teensy LC mit RFM95 90 µA
    Arduino Pro mit RFM95 DS18b20 6 µA
    Arduino Pro mit RFM95 BME280 BH1750 11 µA

    0
Log in to reply
 

Suggested Topics

  • hek


    Announcements •  

    3
  • Gibber


    Troubleshooting •  

    8
  • DIY89


    Troubleshooting •  

    6
  • kamilb85


    Troubleshooting •  

    2

11
Online

11.4k
Users

11.1k
Topics

112.7k
Posts



Copyright 2019 Sensnology   |   Forum Guidelines   |   Privacy Policy   |   Terms of Service