[solved] RPI Gateway with RFM95 does not receive any nodes

mfalkvidd

Adding link to the github issue, in case the information there helps anyone: https://github.com/mysensors/MySensors/issues/863

mfalkvidd

@micropet Since no-one else seems to be able to help, I have dug out an old raspberry pi and started to retrace your steps. It is going slow, but forwards.

One thing I notice is that the configure command above does not include --my-transport=rfm95

Just a quick check - was rfm95 included in your configure command?

Also, could you post the debug output from the gateway?

I realize that you might have given up, but I hope to be able to check that rfm95 works.

mfalkvidd

I now have the gateway up and running, at least it seems so:

pi@raspi1:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Config file /etc/mysensors.dat does not exist, creating new config file.
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

Parsed log

Next step is to build a rfm95 node.

EDIT: My configure command:

./configure --my-transport=rfm95

mfalkvidd

My test node (a binary switch that toggles state every 2 seconds) is able to communicate with the gateway.

Gateway log:

mysgw: Config file /etc/mysensors.dat does not exist, creating new config file.
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:SAN:OK
mysgw: TSM:READY:NWD REQ
mysgw: TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
mysgw: TSF:SRT:OK
mysgw: TSF:SAN:OK
mysgw: TSF:MSG:READ,102-102-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=102
mysgw: TSF:PNG:SEND,TO=0
mysgw: TSF:CKU:OK
mysgw: TSF:MSG:GWL OK
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:PINGED,ID=102,HP=1
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
mysgw: TSF:MSG:READ,102-102-0,s=255,c=0,t=17,pt=0,l=10,sg=0:2.2.0-beta
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=11,pt=0,l=13,sg=0:Binary Sensor
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=0,t=0,pt=0,l=0,sg=0:
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1

Node log:

5134 MCO:BGN:INIT NODE,CP=RLNNE---,VER=2.2.0-beta
5176 TSM:INIT
5177 TSF:WUR:MS=0
5194 TSM:INIT:TSP OK
5196 TSF:SID:OK,ID=102
5198 TSM:FPAR
5248 TSF:MSG:SEND,102-102-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
5881 TSF:MSG:READ,0-0-102,s=255,c=3,t=8,pt=1,l=1,sg=0:0
5886 TSF:MSG:FPAR OK,ID=0,D=1
7255 TSM:FPAR:OK
7256 TSM:ID
7257 TSM:ID:OK
7258 TSM:UPL
7363 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
7414 TSF:MSG:READ,0-0-102,s=255,c=3,t=25,pt=1,l=1,sg=0:1
7419 TSF:MSG:PONG RECV,HP=1
7422 TSM:UPL:OK
7423 TSM:READY:ID=102,PAR=0,DIS=1
7558 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
7609 TSF:MSG:READ,0-0-102,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
7764 TSF:MSG:SEND,102-102-0-0,s=255,c=0,t=17,pt=0,l=10,sg=0,ft=0,st=OK:2.2.0-beta
7865 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
9990 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=11,pt=0,l=13,sg=0,ft=0,st=OK:Binary Sensor
10102 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
10203 TSF:MSG:SEND,102-102-0-0,s=3,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK:
10209 MCO:REG:REQ
10305 TSF:MSG:SEND,102-102-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
10356 TSF:MSG:READ,0-0-102,s=255,c=3,t=27,pt=1,l=1,sg=0:1
10361 MCO:PIM:NODE REG=1
10363 MCO:BGN:STP
10365 MCO:BGN:INIT OK,TSP=1
10501 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
12614 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
14728 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
16833 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
18938 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
21052 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
23158 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
25272 TSF:MSG:SEND,102-102-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1

micropet

Thanks for testing.

Transport word in it. The line was something mixed up here in the forum. :)

./configure --my-gateway=mqtt --my-controller-ip-address=192.168.0.23 --my-mqtt-publish-topic-prefix=mysensors2-out --my-mqtt-subscribe-topic-prefix=mysensors2-in --my-mqtt-client-id=mygateway5 --my-transport=rfm95 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18

The Gateway shows:

./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.0.23
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors2-out/0/255/0/0/18

I have to look for a MySensor Node.
I had changed everything to the TTN network.

I'll get back to you.

Greetings Peter

mfalkvidd

@micropet great. The problem might be mqtt related. I am not sure if I have a mqtt broker to connect to so I just tried the ethernet variant. Could you see if switching to ethernet helps? That would narrow down the scope.

micropet

Thus, the node is in operation. The gateway does not show anything new.

I need mqtt. My RFM69 Nodes (433 MHz and 868 MHz) also run with mqtt.

The Node output is:

0 MCO:BGN:INIT NODE,CP=RLNNA---,VER=2.2.0-beta
4 TSM:INIT
4 TSF:WUR:MS=0
6 RFM95:INIT
8 RFM95:INIT:PIN,CS=10,IQP=4,IQN=0
22 RFM95:PTX:LEVEL=5
24 TSM:INIT:TSP OK
26 TSM:INIT:STATID=150
28 TSF:SID:OK,ID=150
30 TSM:FPAR
32 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
2037 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4046 !TSM:FPAR:NO REPLY
4048 TSM:FPAR
4050 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
6057 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8067 !TSM:FPAR:NO REPLY
8069 TSM:FPAR
8071 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
10076 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
12085 !TSM:FPAR:NO REPLY
12087 TSM:FPAR
12089 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
14094 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
16103 !TSM:FPAR:FAIL
16105 TSM:FAIL:CNT=1
16107 TSM:FAIL:DIS
16109 TSF:TDI:TSL
16111 RFM95:RSL
26114 TSM:FAIL:RE-INIT
26116 TSM:INIT
26118 RFM95:INIT
26120 RFM95:INIT:PIN,CS=10,IQP=4,IQN=0
26134 RFM95:PTX:LEVEL=5
26136 TSM:INIT:TSP OK
26138 TSM:INIT:STATID=150
26140 TSF:SID:OK,ID=150
26144 TSM:FPAR
26146 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
28151 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
30162 !TSM:FPAR:NO REPLY
30164 TSM:FPAR
30167 RFM95:SWR:SEND,TO=255,SEQ=0,RETRY=0
32172 TSF:MSG:SEND,150-150-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

mfalkvidd

@micropet I understand you prefer mqtt. But if you are able to verify that the gateway works with ethernet, we would know that the problem is mqtt related. Now the problem might be related to anything.

micropet

Yes I understand.
I'm just checking the pin assignment of the node.
How did you connect the Node to the RFM95?

micropet

I use the same connections as for a TTN node.

Board is Arduino Pro mini.

10 NSS CS
13 SCK
11 MOSI
12 MISO

4 DI00
5 DIO1

And have in the sketch:

#define MY_RFM95_CS_PIN 10 // NSS
#define MY_RFM95_IRQ_PIN 4 // IRQ D100

mfalkvidd

@micropet mqtt works:

pi@raspi1:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.1.101
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors-rfm95-out/0/255/0/0/18
mysgw: TSF:MSG:READ,102-102-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=102
mysgw: TSF:PNG:SEND,TO=0
mysgw: TSF:CKU:OK
mysgw: TSF:MSG:GWL OK
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
mysgw: TSF:MSG:PINGED,ID=102,HP=1
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
mysgw: TSF:MSG:READ,102-102-0,s=255,c=0,t=17,pt=0,l=10,sg=0:2.2.0-beta
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/0/0/17
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/3/0/6
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=11,pt=0,l=13,sg=0:Binary Sensor
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/3/0/11
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
mysgw: Sending message on topic: mysensors-rfm95-out/102/255/3/0/12
mysgw: TSF:MSG:READ,102-102-0,s=3,c=0,t=0,pt=0,l=0,sg=0:
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/0/0/0
mysgw: TSF:MSG:READ,102-102-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
mysgw: TSF:MSG:SEND,0-0-102-102,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16
mysgw: TSF:MSG:READ,102-102-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors-rfm95-out/102/3/1/0/16

I used this configure command:

./configure --my-gateway=mqtt --my-controller-ip-address=192.168.1.101 --my-mqtt-publish-topic-prefix=mysensors-rfm95-out --my-mqtt-subscribe-topic-prefix=mysensors-rfm95-in --my-mqtt-client-id=mygateway-rfm95 --my-transport=rfm95 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18

For the wiring, I used the instructions for rfm69 on the raspberry pi gateway page.

mfalkvidd

For the node, I used this sketch (esp8266 nodemcu):

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM95

#define MY_RFM95_CS_PIN D8 // NSS
#define MY_RFM95_IRQ_PIN D1 // IRQ DIO0
#define MY_RFM95_RST_PIN D3 // Reset, not connected


#include <MySensors.h>

#define SKETCH_NAME "Binary Sensor"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
#define SECONDARY_CHILD_ID 4

#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch
#define SECONDARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

#if (PRIMARY_BUTTON_PIN < 2 || PRIMARY_BUTTON_PIN > 3)
#error PRIMARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (SECONDARY_BUTTON_PIN < 2 || SECONDARY_BUTTON_PIN > 3)
#error SECONDARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (PRIMARY_BUTTON_PIN == SECONDARY_BUTTON_PIN)
#error PRIMARY_BUTTON_PIN and BUTTON_PIN2 cannot be the same
#endif
#if (PRIMARY_CHILD_ID == SECONDARY_CHILD_ID)
#error PRIMARY_CHILD_ID and SECONDARY_CHILD_ID cannot be the same
#endif


// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);

void setup()
{

}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER "." SKETCH_MINOR_VER);

  // Register binary input sensor to sensor_node (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  present(PRIMARY_CHILD_ID, S_DOOR);
}

// Loop will iterate on changes on the BUTTON_PINs
void loop()
{
  static uint8_t sentValue = 2;

  // Short delay to allow buttons to properly settle
  wait(5);

  uint8_t  value = !sentValue;

  if (value != sentValue) {
    // Value has changed from last transmission, send the updated value
    send(msg.set(value == HIGH));
    sentValue = value;
  }

  wait(2000);
}

micropet

My gateway will work, I think.

Pity,

I am using an Arduino Pro mini.
I can make a node with esp8266.
But I can not do that today, I think I have time for it tomorrow.

mfalkvidd

@micropet no rush, you've had to wait a long time to get any help :wink:
Just post here when/if you have some news. If you are unable to find an esp I can probably find a Pro Mini and build a node.

micropet

Have a node with a NodeMCU built.
Does not work either.
At the gateway comes nothing.
Since I must look further.

22820 !TSM:FPAR:NO REPLY
22822 TSM:FPAR
24824 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
26831 !TSM:FPAR:NO REPLY
26833 TSM:FPAR
28835 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
30842 !TSM:FPAR:NO REPLY
30844 TSM:FPAR
32846 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
34853 !TSM:FPAR:FAIL
34854 TSM:FAIL:CNT=1
34856 TSM:FAIL:DIS
34858 TSF:TDI:TSL
44860 TSM:FAIL:RE-INIT
44861 TSM:INIT
44878 TSM:INIT:TSP OK
44880 TSF:SID:OK,ID=33
44882 TSM:FPAR
46885 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
48892 !TSM:FPAR:NO REPLY
48894 TSM:FPAR
50896 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
52903 !TSM:FPAR:NO REPLY
52905 TSM:FPAR
54907 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
56914 !TSM:FPAR:NO REPLY
56916 TSM:FPAR
58918 TSF:MSG:SEND,33-33-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
60925 !TSM:FPAR:FAIL
60926 TSM:FAIL:CNT=2
60928 TSM:FAIL:DIS
60930 TSF:TDI:TSL

micropet

A Node with a Pro mini or a Teensy would help me more.

All my RFM69 Nodes have a Pro mini (50 pcs)
The TTN Nodes a Pro mini or a Teensy. (Approx. 20 pieces)

micropet

Now I do not understand anything anymore.

I have made an update on the RPI and compiled the gateway software again.
I had already done more than 10 times.
After the start of the RPI nothing worked.
Multiple resets of the NodeMCU also brought nothing.

I pulled the micro usb plug and plugged again - suddenly it works. WAU

Then I must have a fault in the wiring between the RFM95 and the Arduino Pro.
Just for info: I had set up 5 pieces. All do not work.

./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RLNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.0.23
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors2-out/0/255/0/0/18
mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:0
mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16
mysgw: TSF:MSG:READ,33-33-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
mysgw: Sending message on topic: mysensors2-out/33/3/1/0/16

micropet

Hi,

I have connected my Arduino Pro Nodes. They do not work.
The ESP Node has been running since last night without problems.

Can you try an Arduino?

mfalkvidd

@micropet great work. I should be able to set up an Arduino node tomorrow. The forecast shows rain anyway :)

micropet

Fine.

I'm just trying a Teensy LC Node.
See you tomorrow.

Here in Essen, Germany, it should also rain. :)

[solved] RPI Gateway with RFM95 does not receive any nodes

25

11.7k

11.2k

113.1k