Can't send message over arduino serial monitor

[botbite]

Ok so I have got a few questions and a problem to solve
I have two arduino unos hooked up with the nrf24l01+ one is running the (arduino button relay) and the other is running the (serial gateway) examples. Once I plug the sensors in I Ioad arduino running the gateway into the serial moniter and it gives me the normal "0;0;3;0;14;Gateway start up complete." then I turn on the (relay button arduino) and it gives me a confirming
"105;255;0;0;18;1.4.1
0;0;3;0;9;read: 105-105-0 s=255,c=3,t=6,pt=1,l=1:0
105;255;3;0;6;0
0;0;3;0;9;read: 105-105-0 s=255,c=3,t=11,pt=0,l=14:Relay & Button
105;255;3;0;11;Relay & Button
0;0;3;0;9;read: 105-105-0 s=255,c=3,t=12,pt=0,l=3:1.0
105;255;3;0;12;1.0
0;0;3;0;9;read: 105-105-0 s=1,c=0,t=3,pt=0,l=5:1.4.1
105;1;0;0;3;1.4.1"

So, I have good connection and the node is all set up. So then I try and give the node a command to turn on or off, so I type into the serial monitor
105;1;1;1;2;1\n
or 105;1;1;1;2;0\n
or 105;1;0;1;2;1\n
or 105;1;1;0;2;0\n
or 105;0;1;1;2;1\n
or 105;0;1;1;2;0\n
just about every variation that you could imagine and nothing.
The biggest question I have is, Am i supposed to type anything in before 105;1;1;1;2;1\n ?
Is there a method that I am supposed to call up? I am writing directly into the serial monitor form the arduino ide, and am running the 1.4 library of Mysensors. Is there supposed to be anything else with the message"105;1;1;1;2;1\n" to help this message to compute to the relay?
thanks?

[kalle]

This post is deleted!

[botbite]

the funny thing is I know the everything is hooked up right because everything works through a controller? Has anyone else tried to get this to work just through the serial monitor?

[hek]

What is you newline/cr setting in serial monitor?

Are you actually typing \n ?

\n == enter/carriage return

[botbite]

The setting has been "No line Ending" And I tried typing it in both ways with the \n and without (105;1;1;1;2;1\n and 105;1;1;1;2;1). What setting should I be in in the serial monitor and what should I type into the serial monitor?
Thank you so much for responding, I am really interested in all this and it looks like you guys have done such a great job! Thanks!

[hek]

The serial monitor setting should be set to "with line ending".

You should not typ "\n"!
It means that you should press enter on your keyboard.

[epierre]

Hello,

2015-01-28 10:36:55 9 255 0 0 18 1.4.1
2015-01-28 10:36:55 9 255 3 0 6 0
2015-01-28 10:36:56 9 255 3 0 11 Relay
2015-01-28 10:36:56 9 255 3 0 12 1.0
2015-01-28 10:36:56 9 1 0 0 3 1.4.1

I can send this:

echo "9;3;1;0;2;1\n" >> /dev/ttyUSB0

On the device serial line I see:

read: 0-0-9 s=3,c=1,t=2,pt=0,l=3:1\n
Incoming change for sensor:3, New status: 1

[daulagari]

You should not typ "\n"!
It means that you should press enter on your keyboard.

On Linux I saw that I have to send "\r\n" instead of "\n".
"\r\n" (Carriage return, Line feed) is the Windows return, "\n" only the Linux return.