Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Connect NodeMCU to its own created network

sabiha patan last edited by sabiha patan

Can a NodeMCU connect to its own created network?
Reply Quote 0
1 Reply Last reply
gohan Mod last edited by

Pls explain better the purpose
Reply Quote 1
1 Reply Last reply
sabiha patan last edited by

A NodeMCU is acting as an access point and it created a network. Now, can this NodeMCU can be connected to its own created network?
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by @sabiha patan

@sabiha-patan it is always connected to its own created network. There is no way to disconnect.
Reply Quote 0
1 Reply Last reply

4
Posts

756
Views

Log in to reply

Suggested Topics

RFM95 network problem (RPI & Arduino GW)
Troubleshooting • • m3nt4lll

9

0
Votes

9
Posts

1253
Views

Alright, Sometimes the solution is pretty obvious but you fail to spot it. @tekka thanks for pointing me to the correct direction, as the problem was in the used frequency. Even though I initially tried with 434 MHz, it turns out that when i finally did it right, i had already switched to the default 868. After adding #define MY_RFM95_FREQUENCY RFM95_434MHZ in the sketches initially, i established communication. After that i also tried to configure again the rasperry (this time knowing that the node is working) and Hooray! it worked Thank you all for your support and @titvs @mfalkvidd as well. This topic can now be locked
wired RS485 sensor network does not work
Troubleshooting • • wimd

5

0
Votes

5
Posts

1417
Views

@dbemowsk Thank you for the reply. I searched in the meantime and found on the form that 'rs485 on nano' topic describes exactely the same issue I have. I see that you are involved there. I will join that chat as more people are involved.
MySensors network crashed
Troubleshooting • • Tore André Rosander

2

0
Votes

2
Posts

1252
Views

@Tore-André-Rosander you could do a tail on your gateways serial device. Currently @work so I can't look it up for you. But that should show the serial communication between the gateway and domoticz. Also you can check the log of Domoticz in the log console of Domoticz
Creating Wireless Sensor Network
Troubleshooting • • codergirl56

3

0
Votes

3
Posts

806
Views

@codergirl56 Reading your question, I think your starting point is to have a look at the pingpong example (see below for the direct link) which comes with the mysensors library and try to modify it such that it starts sending the RFID data. direct link to pingpong example First you'd need to install the mysensors library of course, see the download page. How to do that is in the "Getting Started" as mentioned by @AWI. Just start reading and you'll be guided to it. good luck Boozz
MySensor Network on RS485 - only single node visible
Troubleshooting • mysensors • • Rysiek

13

0
Votes

13
Posts

151
Views

Very useful topic for me, thanks. Even though it's been a long time, the information was useful to me. And especially the information on the link you sent.
Ethernet Gateway not showing on network
Troubleshooting • • spork

5

0
Votes

5
Posts

2153
Views

For me the problem was the hang in setup at gw.begin call. I solved reading this old topic : http://forum.mysensors.org/topic/773/ethernetgateway-hangs-after-gateway-startup-complete.
Occasional MySensors network drop outs
Troubleshooting • • Nick Willis

14

1
Votes

14
Posts

1672
Views

@Nick-Willis It's simply a case of attaching the serial Tx/Rx on the pi to the Tx/Rx on the arduino (use 3.3V arduino or a level shifter if using 5V pro mini).... Don'e be tempted to use the pi 3.3V supply for the radio or pro mini - take the 5V supply from the pi and use this via a regulator to get cleaner 3.3v...... Originally I used the 662k, but now use AMS1117 3.3V as it is cleaner DC and can give more current for the radio tx pulses.
W5100 gateway not connecting to network
Troubleshooting • • hautomate

5

0
Votes

5
Posts

2681
Views

Hello, I teste this solution out and it worked My W5100 is now working! Use as reference the post https://forum.arduino.cc/index.php?topic=351477.msg2662072#msg2662072

34
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1