Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Connect NodeMCU to its own created network

sabiha patan last edited by sabiha patan

Can a NodeMCU connect to its own created network?
Reply Quote 0
1 Reply Last reply
gohan Mod last edited by

Pls explain better the purpose
Reply Quote 1
1 Reply Last reply
sabiha patan last edited by

A NodeMCU is acting as an access point and it created a network. Now, can this NodeMCU can be connected to its own created network?
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by @sabiha patan

@sabiha-patan it is always connected to its own created network. There is no way to disconnect.
Reply Quote 0
1 Reply Last reply

4
Posts

756
Views

Log in to reply

Suggested Topics

MySensors gateway and network reliability
Troubleshooting • • Nick Willis

20

1
Votes

20
Posts

816
Views

If you really enjoy fiddling with connection problems and gateways freezing you should try using the gsm gateway. At first it froze up every day or two. I now run a second mcu just to check connectivity to mycontroller and resetting the gateway when it fails. This sometimes happen a couple of times a day.
RFM95 network problem (RPI & Arduino GW)
Troubleshooting • • m3nt4lll

9

0
Votes

9
Posts

1253
Views

Alright, Sometimes the solution is pretty obvious but you fail to spot it. @tekka thanks for pointing me to the correct direction, as the problem was in the used frequency. Even though I initially tried with 434 MHz, it turns out that when i finally did it right, i had already switched to the default 868. After adding #define MY_RFM95_FREQUENCY RFM95_434MHZ in the sketches initially, i established communication. After that i also tried to configure again the rasperry (this time knowing that the node is working) and Hooray! it worked Thank you all for your support and @titvs @mfalkvidd as well. This topic can now be locked
Occasional MySensors network drop outs
Troubleshooting • • Nick Willis

14

1
Votes

14
Posts

1672
Views

@Nick-Willis It's simply a case of attaching the serial Tx/Rx on the pi to the Tx/Rx on the arduino (use 3.3V arduino or a level shifter if using 5V pro mini).... Don'e be tempted to use the pi 3.3V supply for the radio or pro mini - take the 5V supply from the pi and use this via a regulator to get cleaner 3.3v...... Originally I used the 662k, but now use AMS1117 3.3V as it is cleaner DC and can give more current for the radio tx pulses.
RFID and NRF24L01 Wireless Network Coding Issues
Troubleshooting • • codergirl56

23

0
Votes

23
Posts

9339
Views

@Ispandy, let resume some things because I'm lost You copied the sketch code from node 3 (= correctly running node with cardscans and remote control from openhab) to node 50 and you adapted the node id. This same sketch on node 50 is running correctly with cardscans but not with openhab? Correct? If above is correct: somewhere your openhab configuration for this node 50 is not correct. You say that node 50 is never receiving the openhab command, so there is a problem with your openhab configuration for node 50.
Simple network not working.
Troubleshooting • • Markus Tenghall

4

0
Votes

4
Posts

1821
Views

@Markus-Tenghall Hope you'll have lots of fun!
W5100 gateway not connecting to network
Troubleshooting • • hautomate

5

0
Votes

5
Posts

2681
Views

Hello, I teste this solution out and it worked My W5100 is now working! Use as reference the post https://forum.arduino.cc/index.php?topic=351477.msg2662072#msg2662072
MySensor Network on RS485 - only single node visible
Troubleshooting • mysensors • • Rysiek

13

0
Votes

13
Posts

151
Views

Very useful topic for me, thanks. Even though it's been a long time, the information was useful to me. And especially the information on the link you sent.
MySensors network crashed
Troubleshooting • • Tore André Rosander

2

0
Votes

2
Posts

1252
Views

@Tore-André-Rosander you could do a tail on your gateways serial device. Currently @work so I can't look it up for you. But that should show the serial communication between the gateway and domoticz. Also you can check the log of Domoticz in the log console of Domoticz

27
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1