Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 Ebyte nRF52832 Prototyping Board

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/472/Ebyte-nRF52832-Prototyping-Board
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by NeverDie

I suppose panelizing this board together with a pure prototype board might achieve the objective I was aiming for....
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

It works. Project completed.
Reply Quote 2
1 Reply Last reply
NeverDie Hero Member last edited by

I recommend snipping off the DTR pin using flush cutters. Given the current configuration, it isn't going to work properly.
Reply Quote 0
1 Reply Last reply
ahmedadelhosni last edited by

Can you please propose what type of inductors and capacitors did you use ?
A BOM will be great.

Actually I am asking because I knew there is something called SRF from this topic https://devzone.nordicsemi.com/question/171472/filter-inductor-requirement-for-nrf52832-in-dcdc-mode/

Thanks.
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by @ahmedadelhosni

@ahmedadelhosni said in Ebyte nRF52832 Prototyping Board:

Can you please propose what type of inductors and capacitors did you use ?
A BOM will be great.

It is exactly the same BOM as this: https://www.openhardware.io/view/471/Ebyte-nRF52832-Small-Breakout-Board#tabs-bom
Reply Quote 0
1 Reply Last reply
ahmedadelhosni last edited by @NeverDie

@NeverDie thanks
Reply Quote 0
1 Reply Last reply

7
Posts

1896
Views

Log in to reply

Suggested Topics

💬 VR-Shield
OpenHardware.io • bluetooth shield sensors virtual reality imus • • openhardware.io

1

0
Votes

1
Posts

10
Views

No one has replied
💬 MyMultisensors
OpenHardware.io • temperature humidity atsha204a motion pir low power coincell multi sensor ambiant light 328p • • openhardware.io

176

7
Votes

176
Posts

61159
Views

@scalz I have just updated to MySensors 2.3.2 and the sketch with interrupts stopped working. Any changes in any lib?
💬 In-wall scene controller OLED keypad
OpenHardware.io • mysensors scene controller wall switch oled display keypad • • openhardware.io

7

0
Votes

7
Posts

2048
Views

@Michael-Link I have been out of touch with MySensors for some time now and looking to slowly get back into it. I created this and a few other boards back in 2018 All of the GERBER files for this are in the "Design Files" tab. Those you should be able to send to JLC PCB or one of the other fab houses and have some made. This was designed to be used with 2 other boards that I designed. There was the processor board and the power supply board. The processor board was designed in a way that I could use a couple different switch boards. This one and a universal multi-switch board that had multiple configurations. If you look here you will see my other boards.
💬 AC-DC double solid state relay module
OpenHardware.io • light hlk-pm01 acdc light switch solid state relay • • openhardware.io

226

7
Votes

226
Posts

103487
Views

What I didn't quite figure out was how it operates independently as a regular light switch. What I find most interesting is that this is 8 years old. There have been some incredible advances in the IoT world in that time. I was about to do a similar thing which morphed into an ESP-12F then added a touch screen. I call it the Universal Light Switch Imagine this: All the switches are identical. Any switch can easily be configured to control up to five devices ... and then changed, on-the-fly, to control a different set of devices. My design is part of a system that would require a controller (eg. Home Assistant), an MQTT broker, and receiving modules in the devices being switched. It's WiFI which assumes an access point. The DIY ULS is under $20 and the off-the-shelf receiving modules are under $10. (About the cost of a non-networked dimmer switch) If one doesn't have the controller and MQTT broker, they can run on an old (5 years?) computer (which is cheaper than an old RasberryPi). This project is a good one! OSD
💬 Pinect Hand-Free Game Console
OpenHardware.io • arduino pcb motion sensor console game android scheme camera • • openhardware.io

1

0
Votes

1
Posts

7
Views

No one has replied

2
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1