Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 Ebyte nRF52832 Prototyping Board

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/472/Ebyte-nRF52832-Prototyping-Board
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by NeverDie

I suppose panelizing this board together with a pure prototype board might achieve the objective I was aiming for....
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

It works. Project completed.
Reply Quote 2
1 Reply Last reply
NeverDie Hero Member last edited by

I recommend snipping off the DTR pin using flush cutters. Given the current configuration, it isn't going to work properly.
Reply Quote 0
1 Reply Last reply
ahmedadelhosni last edited by

Can you please propose what type of inductors and capacitors did you use ?
A BOM will be great.

Actually I am asking because I knew there is something called SRF from this topic https://devzone.nordicsemi.com/question/171472/filter-inductor-requirement-for-nrf52832-in-dcdc-mode/

Thanks.
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by @ahmedadelhosni

@ahmedadelhosni said in Ebyte nRF52832 Prototyping Board:

Can you please propose what type of inductors and capacitors did you use ?
A BOM will be great.

It is exactly the same BOM as this: https://www.openhardware.io/view/471/Ebyte-nRF52832-Small-Breakout-Board#tabs-bom
Reply Quote 0
1 Reply Last reply
ahmedadelhosni last edited by @NeverDie

@NeverDie thanks
Reply Quote 0
1 Reply Last reply

7
Posts

1896
Views

Log in to reply

Suggested Topics

💬 In-wall scene controller OLED keypad
OpenHardware.io • mysensors scene controller wall switch oled display keypad • • openhardware.io

7

0
Votes

7
Posts

2050
Views

@Michael-Link I have been out of touch with MySensors for some time now and looking to slowly get back into it. I created this and a few other boards back in 2018 All of the GERBER files for this are in the "Design Files" tab. Those you should be able to send to JLC PCB or one of the other fab houses and have some made. This was designed to be used with 2 other boards that I designed. There was the processor board and the power supply board. The processor board was designed in a way that I could use a couple different switch boards. This one and a universal multi-switch board that had multiple configurations. If you look here you will see my other boards.
💬 Syma S107 Bluetooth mod (connect any toy with your phone!)
OpenHardware.io • nrf52832 nrf52 remote control hack bluetooth low energy toys • • openhardware.io

1

0
Votes

1
Posts

9
Views

No one has replied
💬 SimSpirit Motion Simulator Support 360° Yaw, Pitch and Roll
OpenHardware.io • motion-simulator head-tracking • • openhardware.io

1

0
Votes

1
Posts

10
Views

No one has replied
💬 MySensors InCan double light switch
OpenHardware.io • mysensors nrf24l01 relay switch light hlk-pm01 acdc in-wall • • openhardware.io

24

1
Votes

24
Posts

2442
Views

The author has done some good work ensuring good design practices; trace separation, fuses, etc. but I don't see any extra I/O brought out on this particularl switch. You would have to carefully solder to the chip itself, and modify the code a bit. You could use magnetic switches. Put a magnet on the blinds and the switch in window sill. The author notes that this is not an Arduino, but uses the same chip that the Arduino uses. The author doesn't explain how the chip is programmed. This method could have been used. It may be just as easy to use an RF Nano with a little power supply. This suggestion is not nearly as robust as the author's. For example, these power supplies have gotten bad reviews mainly because the mains power traces are too close together. I justify using them because in all likelihood a failure will pop the power supply and probably the Nano, too, noting that these are cheaper than the fuses you would put in to protect them. I am fully aware of the risks involved in doing this, and you should be, too (eg. burning down your house). -OSD
💬 HLK-PM01 breakout board
OpenHardware.io • hlk-pm01 • • openhardware.io

38

0
Votes

38
Posts

5408
Views

what the ratings are of the two capacitors used in your circuit? A 1000 uF and a 100 uF?

34
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1