Gateway not responding to I_ID_REQUEST from sensors
-
Hi all,
I recently bought a Senserbender gateway and multiple micros from itead. Using NRF24 radios with the extra cap.
It seems that the radio is working fine as soon as I turn on the sensor the gateway starts receiving requests I_ID_REQUEST
114516 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
However there's no response on the gateway, I'm expecting it to send something back.
I tried uploading the standard senserbend gateway serial sketch again with 2.3.2 (tried older libraries as well) but I get the same. Interestingly I had the same results using a standard arduino. I also have a couple of extra radios and tried multiple ones. Cleared eprom, using LOW power, tried moving them farther and closer.
I have not yet tried uploading the sensor sketches as I don't have a programmer yet. Is there anything else I could try?
logs:
21:49:16.519 -> 0;255;3;0;9;3092 MCO:BGN:INIT GW,CP=RNNGS---,FQ=48,REL=255,VER=2.3.2
21:49:16.552 -> 0;255;3;0;9;3121 TSF:LRT:OK
21:49:16.552 -> 0;255;3;0;9;3121 TSM:INIT
21:49:16.552 -> 0;255;3;0;9;3122 TSF:WUR:MS=0
21:49:16.552 -> 0;255;3;0;9;3128 TSM:INIT:TSP OK
21:49:16.552 -> 0;255;3;0;9;3128 TSM:INIT:GW MODE
21:49:16.552 -> 0;255;3;0;9;3129 TSM:READY:ID=0,PAR=0,DIS=0
21:49:16.552 -> 0;255;3;0;9;3129 MCO:REG:NOT NEEDED
21:49:16.552 -> 0;255;3;0;14;Gateway startup complete.
21:49:16.552 -> 0;255;0;0;18;2.3.2
21:49:16.552 -> 0;255;3;0;9;3130 MCO:BGN:STP
21:49:16.552 -> 0;255;3;0;9;3130 MCO:BGN:INIT OK,TSP=1
21:49:16.552 -> 0;255;3;0;9;3131 TSM:READY:NWD REQ
21:49:16.552 -> 0;255;3;0;9;3134 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
21:51:05.796 -> 0;255;3;0;9;112458 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
21:51:05.796 -> 255;255;3;0;3;
21:51:07.850 -> 0;255;3;0;9;114516 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
21:51:07.850 -> 255;255;3;0;3;
21:51:09.903 -> 0;255;3;0;9;116568 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
21:51:09.903 -> 255;255;3;0;3; -
Hi all,
I recently bought a Senserbender gateway and multiple micros from itead. Using NRF24 radios with the extra cap.
It seems that the radio is working fine as soon as I turn on the sensor the gateway starts receiving requests I_ID_REQUEST
114516 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
However there's no response on the gateway, I'm expecting it to send something back.
I tried uploading the standard senserbend gateway serial sketch again with 2.3.2 (tried older libraries as well) but I get the same. Interestingly I had the same results using a standard arduino. I also have a couple of extra radios and tried multiple ones. Cleared eprom, using LOW power, tried moving them farther and closer.
I have not yet tried uploading the sensor sketches as I don't have a programmer yet. Is there anything else I could try?
logs:
21:49:16.519 -> 0;255;3;0;9;3092 MCO:BGN:INIT GW,CP=RNNGS---,FQ=48,REL=255,VER=2.3.2
21:49:16.552 -> 0;255;3;0;9;3121 TSF:LRT:OK
21:49:16.552 -> 0;255;3;0;9;3121 TSM:INIT
21:49:16.552 -> 0;255;3;0;9;3122 TSF:WUR:MS=0
21:49:16.552 -> 0;255;3;0;9;3128 TSM:INIT:TSP OK
21:49:16.552 -> 0;255;3;0;9;3128 TSM:INIT:GW MODE
21:49:16.552 -> 0;255;3;0;9;3129 TSM:READY:ID=0,PAR=0,DIS=0
21:49:16.552 -> 0;255;3;0;9;3129 MCO:REG:NOT NEEDED
21:49:16.552 -> 0;255;3;0;14;Gateway startup complete.
21:49:16.552 -> 0;255;0;0;18;2.3.2
21:49:16.552 -> 0;255;3;0;9;3130 MCO:BGN:STP
21:49:16.552 -> 0;255;3;0;9;3130 MCO:BGN:INIT OK,TSP=1
21:49:16.552 -> 0;255;3;0;9;3131 TSM:READY:NWD REQ
21:49:16.552 -> 0;255;3;0;9;3134 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
21:51:05.796 -> 0;255;3;0;9;112458 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
21:51:05.796 -> 255;255;3;0;3;
21:51:07.850 -> 0;255;3;0;9;114516 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
21:51:07.850 -> 255;255;3;0;3;
21:51:09.903 -> 0;255;3;0;9;116568 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
21:51:09.903 -> 255;255;3;0;3; -
Feeling embarrassed not reading page 3 of the intro docs just assuming roles of the components... after your comment I got this up and running within 10mins. Thank you! :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login