Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Blogs and Articles about MySensors

hek Admin 11 Mar 2015, 07:59 last edited by

Post backlinks to your blog entries and articles about your MySensors projects here.
Reply Quote 0
1 Reply Last reply
Loading More Posts
2
Posts

1.4k
Views
Reply

Reply as topic
Log in to reply
automatiserar.se 11 Mar 2015, 08:10 last edited by

Hi everybody!

Automatiserar.se is a Swedish site that has written a article about MySensors and a small "How to" for Vera.
Check it out!

http://www.automatiserar.se/guide-arduino-sensorer-till-veran-med-mysensors
Reply Quote 0
1 Reply Last reply

2
Posts

1.4k
Views

Log in to reply

2 out of 2

Suggested Topics

Welcome
Announcements • 23 Mar 2014, 08:24 • hek 2 Apr 2014, 14:39

8

0
Votes

8
Posts

3.2k
Views

2 Apr 2014, 14:39

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Simulate Online-Recreating 'Flappy Bird' with Arduino Nano
My Project • 15 Jan 2025, 09:13 • Skylar Jones 15 Jan 2025, 09:13

1

0
Votes

1
Posts

17
Views

No one has replied
Nb of possible nodes in a mysensors networks with domoticz
My Project • 13 Jan 2025, 18:10 • GLAB 16 Feb 2025, 01:11

18

0
Votes

18
Posts

133
Views

16 Feb 2025, 01:11

@OldSurferDude yeah, 10 virgin nodes powered up at the same time is a bad idea I seem to remember reading somwewhere here warning aginst that. If yu have node ID trust issues with Mysensors you should move your address to different locaion as 0x00 is used by Mysensors... just sayin..;)
A low cost energy meter
My Project • 25 Jan 2024, 01:03 • OldSurferDude 12 Aug 2024, 06:03

7

1
Votes

7
Posts

49
Views

12 Aug 2024, 06:03

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.
Interface-board-for-remote-control
My Project • 6 days ago • OldSurferDude 6 days ago

1

0
Votes

1
Posts

11
Views

No one has replied
Wio-E5 (STM32 and SX1262)
My Project • 31 Dec 2024, 17:52 • nagelc 25 Jan 2025, 20:21

2

1
Votes

2
Posts

25
Views

25 Jan 2025, 20:21

Quick Range Check on the WIO-E5-LE. The LE version uses only the low power PA, +14dBm max. Using the default settings except for 915MHz #define MY_SX126x_FREQUENCY (SX126x_915MHZ) #define MY_SX126x_LORA_SF LORA_SF7 #define MY_SX126x_LORA_BW LORA_BW_125 #define MY_SX126x_LORA_CR LORA_CR_4_5 I get about 190 meter range, just walking around the neighborhood, line of site except for some trees and power lines. No tuning on the antenna. Just using a 77.9mm wire. Not as dramatic as some have achieved with LoRa radio's, but plenty good enough for my house and yard : )

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1