Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

BT832X PA / LNA

nagelc last edited by nagelc

Has anyone developed a PA LNA driver for the BT832X (Fanstell NRF5 module)? Works quite well without it, but wondering if could be even better.
@NeverDie , you had a remote control using PA. Was there any additional code for that from stock MySensors NRF5? Did you ever do anything with the LNA part?
Reply Quote 0
1 Reply Last reply

1
Posts

13
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Interface-board-for-remote-control
My Project • • OldSurferDude

2

1
Votes

2
Posts

22
Views

That is a well documented project. Much appreciated
Door chime
My Project • • Paul Scarbro

2

0
Votes

2
Posts

23
Views

@Paul-Scarbro There are multitude of solution, but since we are in MySensors Land, let's do a MySensors solution. You'll quickly see that doing that adds a lot of overhead. We'll use an Arduino Nano or RF Nano if you're going to go whole hog. It can be run from 3.3V or 5V DC, not AC. The reed switch would be connected to an input of the Nano and one of the outputs would drive a relay. The relay would drive the chime. Your C++ program would be something like: #define inputButton 2; // connect reed switch here #define outputRelay 4; // connect relay to this pin see MySensors Relay example #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay void setup() { pinmode(inputButton,INPUT); pinmode(outputRelay,OUTPUT); // put your setup code here, to run once: } void loop() { // put your main code here, to run repeatedly: if (digitalRead(inputButton) == 0) { digitalWrite(outputRelay,RELAY_ON); wait(2000); // wait 2 seconds digitalWrite(outputRelay,RELAY_OFF); // now wait for door to close while(digitalRead(inputButton) == 0) ; //does nothing until reed switch opens } } There are some subtleties that I may have glossed over, but this is the gist. By looking at the MySensors Relay example, you'll see how to integrate this into a MySensors environment. That's where you'd want to get the RF Nano. I've made the assumption you're familiar with the Arduino IDE and you've looked into the MySensors environment.
Radar motion sensor
My Project • • suresh sharma

1

1
Votes

1
Posts

9
Views

No one has replied
Status of my rv(camper) home automation system 2020-2025
My Project • • fsgraz

11

2
Votes

11
Posts

22
Views

@fsgraz Did some testing Today and my RFM range is over 80 meters node to node, with no long range antenna. That will be my next test, just waiting for a shipment from China to arrive. I did how ever notice an extreme improvement when I connected the gateway through a USB hub and then started to dig through the forum. @AWI once wrote about using an external PSU to power the long range NRF PA/LAN. I'll try that this weekend as connecting it to they USB port of my PI extended the range to 20 meters Node to Node.
Wio-E5 (STM32 and SX1262)
My Project • • nagelc

2

1
Votes

2
Posts

27
Views

Quick Range Check on the WIO-E5-LE. The LE version uses only the low power PA, +14dBm max. Using the default settings except for 915MHz #define MY_SX126x_FREQUENCY (SX126x_915MHZ) #define MY_SX126x_LORA_SF LORA_SF7 #define MY_SX126x_LORA_BW LORA_BW_125 #define MY_SX126x_LORA_CR LORA_CR_4_5 I get about 190 meter range, just walking around the neighborhood, line of site except for some trees and power lines. No tuning on the antenna. Just using a 77.9mm wire. Not as dramatic as some have achieved with LoRa radio's, but plenty good enough for my house and yard : )

BT832X PA / LNA

Suggested Topics

Welcome
Announcements • • hek

Interface-board-for-remote-control
My Project • • OldSurferDude

Door chime
My Project • • Paul Scarbro

Radar motion sensor
My Project • • suresh sharma

Status of my rv(camper) home automation system 2020-2025
My Project • • fsgraz

Wio-E5 (STM32 and SX1262)
My Project • • nagelc

24
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

BT832X PA / LNA

Suggested Topics

Welcome Announcements • • hek

Interface-board-for-remote-control My Project • • OldSurferDude

Door chime My Project • • Paul Scarbro

Radar motion sensor My Project • • suresh sharma

Status of my rv(camper) home automation system 2020-2025 My Project • • fsgraz

Wio-E5 (STM32 and SX1262) My Project • • nagelc

24Online

11.5kUsers

11.1kTopics

112.8kPosts

Welcome
Announcements • • hek

Interface-board-for-remote-control
My Project • • OldSurferDude

Door chime
My Project • • Paul Scarbro

Radar motion sensor
My Project • • suresh sharma

Status of my rv(camper) home automation system 2020-2025
My Project • • fsgraz

Wio-E5 (STM32 and SX1262)
My Project • • nagelc

24
Online

11.5k
Users

11.1k
Topics

112.8k
Posts