MySensors battey board revision 1.0
-
Me myself was thinging on using li-ion and depending on space charge controller but atleast protection.
They come in all sizes and dimensions.@Damme look
for indoor usage, while you not very limited with size and you want many things been connected it is still a good choice to use one of the standard arduino
we will do our own board to support real competition with wall z-wave devices but this is second prioritythe first priority are small and battery operated devices
for this purpose you will not find a well prepared standard arduino -
Exciting stuff!
-
What sort of price are we talking about approximately? Made in China?
-
Is there a reason for the 50x50 size? Do you have an enclosure in mind? It almost seems to fit inside a wall junction box.
-
Still wouldn't have minded an AA-battery instead for more than twice the typical mAh. It's only a few mm more. Perhaps this is a moot point, as the more power hungry sensors that I have in mind wouldn't work on battery anyway.
@bjornhallberg said:
- Still wouldn't have minded an AA-battery instead for more than twice the typical mAh. It's only a few mm more. Perhaps this is a moot point, as the more power hungry sensors that I have in mind wouldn't work on battery anyway.
it is not too late to remove holder from the board. it is an option we need to decide.This will allow to be more flexible with power source. But with the holder you can run out of the box at least with temperature sensor
-
-
Me myself was thinging on using li-ion and depending on space charge controller but atleast protection.
They come in all sizes and dimensions.@Damme said:
Me myself was thinging on using li-ion and depending on space charge controller but atleast protection.
They come in all sizes and dimensions.lion is too bad for outdoor usage at least for the places in the world were snow is a normal thing at winter))
AAA is much more universal because you can choose between alkilene and rechargeablewith lion you actually fo not need a step-up
you can use 3.3V version of pro-mini with direct connection between VCC and lion
radio you can connect to lion using 3.3V LDO or 1-2 1n4148 connected simultaneously to drop voltage from 4.2 (fresh lion) bellow 3.6V (maximum allowed for radio) -
@bjornhallberg said:
- Still wouldn't have minded an AA-battery instead for more than twice the typical mAh. It's only a few mm more. Perhaps this is a moot point, as the more power hungry sensors that I have in mind wouldn't work on battery anyway.
it is not too late to remove holder from the board. it is an option we need to decide.This will allow to be more flexible with power source. But with the holder you can run out of the box at least with temperature sensor
@axillent said:
@bjornhallberg said:
- Still wouldn't have minded an AA-battery instead for more than twice the typical mAh. It's only a few mm more. Perhaps this is a moot point, as the more power hungry sensors that I have in mind wouldn't work on battery anyway.
it is not too late to remove holder from the board. it is an option we need to decide.This will allow to be more flexible with power source. But with the holder you can run out of the box at least with temperature sensor
As long as you have the option to (easily) connect / solder wires for a separate 1x or 2x AA holder, or solar I'm sure it'll be fine. And the on-board AAA-battery holder doesn't significantly increase price and / or complicate things. Sounds like something that would be hard to do right without breaking off if it doesn't have the support of an enclosure.
Does it measure and report battery level by any chance?
$15-22 doesn't sound too bad. I mean, if you add up the cost of components for a simple DIY sensor node, including a prototype board etc, you'd come pretty close to $15. And then you'd still be stuck with a lousy Ebay boost module drawing 1mA.
-
@axillent said:
@bjornhallberg said:
- Still wouldn't have minded an AA-battery instead for more than twice the typical mAh. It's only a few mm more. Perhaps this is a moot point, as the more power hungry sensors that I have in mind wouldn't work on battery anyway.
it is not too late to remove holder from the board. it is an option we need to decide.This will allow to be more flexible with power source. But with the holder you can run out of the box at least with temperature sensor
As long as you have the option to (easily) connect / solder wires for a separate 1x or 2x AA holder, or solar I'm sure it'll be fine. And the on-board AAA-battery holder doesn't significantly increase price and / or complicate things. Sounds like something that would be hard to do right without breaking off if it doesn't have the support of an enclosure.
Does it measure and report battery level by any chance?
$15-22 doesn't sound too bad. I mean, if you add up the cost of components for a simple DIY sensor node, including a prototype board etc, you'd come pretty close to $15. And then you'd still be stuck with a lousy Ebay boost module drawing 1mA.
@bjornhallberg the holder adds less than half a dollar to the final price.
You always can use solar connector for any external alternative source
you even will be able to extend life by connecting external AA, on board AAA will start working as soon as AA will run outbattery voltage (level) and external source voltage can be measured and reported by radio. The required connections are build in
Price is still tricky thing because of discussion going on and also because we all are new to such a business. We will need to have also some profit to support project development. I hope all will be withing $15-$22. We are willing to be competitive but not the cheapest. A good level of innovation is an essential idea of the whole project.
Design is open source and anyone can do it himself. -
@axillent Looks good. But is not the LED symbol reversed in the schematics?
I am considering making a board as well for personal use (open HW of course), but using through hole components a bit more extensively for ease of customization. And probably a sockeded MCU so I don't have to include programming interfaces. In the future, I (and hopefully all of you) will push new FW to the board OTA so there will not be a need for holes in the case :)
But I might be interested to join in if your are ordering a batch of these as well. Will it be panelized and pick/placed as well?Do you feel secure today? No? Start requiring some signatures and feel better tomorrow ;)
-
@axillent Looks good. But is not the LED symbol reversed in the schematics?
I am considering making a board as well for personal use (open HW of course), but using through hole components a bit more extensively for ease of customization. And probably a sockeded MCU so I don't have to include programming interfaces. In the future, I (and hopefully all of you) will push new FW to the board OTA so there will not be a need for holes in the case :)
But I might be interested to join in if your are ordering a batch of these as well. Will it be panelized and pick/placed as well?@Anticimex thank you for your attention ) yes, led had a wrong orientation, it was fixed.
I have an DIY experience for making PCB and like you at the beginning willing to use through hole components mostly.
But through the real practice I came to a conclusion that SMD is easy to use, it is cheaper and need much less space.
I also used to make zero-hole PCB using SMD only. This type of PCB requires from me 20-30 minutes of time only for the full production circle. There is 0.5mm copper plates, I use office scissors to cut it in a second.The programming interface (ISP) is not only for the bootloader programming. It can be used for bootloader upgrade or hardware debugging.
Even Nano have it.
The programming interface (FTDI) can be used also for usual Serial.print debugging.
Both interfaces also can be used for additional I/O.Sure, there is no absolute ideal solution. We spend a few months discussing what is a good trade off for this board and you see the result.
What do you mean by "panelized and pick/placed as well"?
sense and drive
-
@Anticimex thank you for your attention ) yes, led had a wrong orientation, it was fixed.
I have an DIY experience for making PCB and like you at the beginning willing to use through hole components mostly.
But through the real practice I came to a conclusion that SMD is easy to use, it is cheaper and need much less space.
I also used to make zero-hole PCB using SMD only. This type of PCB requires from me 20-30 minutes of time only for the full production circle. There is 0.5mm copper plates, I use office scissors to cut it in a second.The programming interface (ISP) is not only for the bootloader programming. It can be used for bootloader upgrade or hardware debugging.
Even Nano have it.
The programming interface (FTDI) can be used also for usual Serial.print debugging.
Both interfaces also can be used for additional I/O.Sure, there is no absolute ideal solution. We spend a few months discussing what is a good trade off for this board and you see the result.
What do you mean by "panelized and pick/placed as well"?
@axillent By panelization that I mean that you send the board to the fab with a BOM, and some reels, and have them solder the components to the board as well. Most if not all fabs will then require you to panelize the board if also picking&placing (that is, multiply the board on a bigger standard-size board, that is fed to the pick&place machine).
Example of a PCB panel
Having a panelized board could also reduce cost for a non pick&placed design, as it allows the manufacturer to make them with less effort (less cutting and less waste).For larger batches this is a good way to save a lot of work, and if good decisions are made on layout, design and component selection, it is not overly expensive either.
I also like SMD, but for "my" board, I was more thinking of having a generic back-bone which can accept a variety of components, so the user can choose what to put on it and use if for various purposes.
Some "standard" interfaces need to exist of course (socket for MCU, power, RF), but the rest (decoupling, IO, etc) is just left "empty" and for the user to populate with the components they would like.And don't get me wrong, ISP/FTDI is really good to have, especially on "in progress" projects. But for the gritty end product, I personally prefer to program and debug the MCU on a breadboard, and then put it in a socket in my optimized board/casing. I even consider using the Arduino "as is".
But it could be that I cannot get my casing to be as small as I want it, without soldering the "bare" MCU directly on the board, and then of course programming interfaces will be needed :) -
@Anticimex thank you for your attention ) yes, led had a wrong orientation, it was fixed.
I have an DIY experience for making PCB and like you at the beginning willing to use through hole components mostly.
But through the real practice I came to a conclusion that SMD is easy to use, it is cheaper and need much less space.
I also used to make zero-hole PCB using SMD only. This type of PCB requires from me 20-30 minutes of time only for the full production circle. There is 0.5mm copper plates, I use office scissors to cut it in a second.The programming interface (ISP) is not only for the bootloader programming. It can be used for bootloader upgrade or hardware debugging.
Even Nano have it.
The programming interface (FTDI) can be used also for usual Serial.print debugging.
Both interfaces also can be used for additional I/O.Sure, there is no absolute ideal solution. We spend a few months discussing what is a good trade off for this board and you see the result.
What do you mean by "panelized and pick/placed as well"?
@axillent said:
There is 0.5mm copper plates, I use office scissors to cut it in a second.
Do you use this thickness for all boards?
And what thickness is the copper? -
Well, needless to say it sounds interesting, when it's been built and tested I'd surely buy a couple of boards. Right now I'm not sure how many actual battery sensors I need and if the sensors I want to run are even viable for battery operation anyway.
I think that for me anyway, more practical things are an issue, like avoiding Swedish customs charges, and finding a GOOD open source automation software so that I can actually use my sensors and not just build them ;-)
If you could also manufacture a separate 3.3V boost circuit based on a modern chip that would be fantastic. I think that is turning out to be a hurdle for most of us that aren't comfortable with SMD/SMT and/or how to nice integrate it into DPI prototyping.
-
@axillent said:
There is 0.5mm copper plates, I use office scissors to cut it in a second.
Do you use this thickness for all boards?
And what thickness is the copper? -
Well, needless to say it sounds interesting, when it's been built and tested I'd surely buy a couple of boards. Right now I'm not sure how many actual battery sensors I need and if the sensors I want to run are even viable for battery operation anyway.
I think that for me anyway, more practical things are an issue, like avoiding Swedish customs charges, and finding a GOOD open source automation software so that I can actually use my sensors and not just build them ;-)
If you could also manufacture a separate 3.3V boost circuit based on a modern chip that would be fantastic. I think that is turning out to be a hurdle for most of us that aren't comfortable with SMD/SMT and/or how to nice integrate it into DPI prototyping.
@bjornhallberg I'm an experienced z-wave user and 1/3 devices I currently have managed by my smart-home are battery based
battery based is most easiest way to launch smart-home without big disaster to the home
I also expect an interest to use this battery as outdoor sensors, while z-wave do not have any alternative to this
with double power outdoor sensor can lasts from a single battery for year or even years depending on solar power.for open source software I personally looking forward to have an integration between mysensors and openhub
A separate boost development was finished today and I'm expecting quotes from our partner.
Any preliminary reservations are welcome.
It will be board 15 x 14.8 mm with a switch between 3.3V (up to 100mA) or 5V output (up to 70mA)
it can be sourced by 1-3 cells alkaline or 1-4 cell ni-mh or 1 cell lionHenrik are build already a boards documentations section on the site :)
We expect to have a good documentation to the boards -
@Damme said:
Me myself was thinging on using li-ion and depending on space charge controller but atleast protection.
They come in all sizes and dimensions.lion is too bad for outdoor usage at least for the places in the world were snow is a normal thing at winter))
AAA is much more universal because you can choose between alkilene and rechargeablewith lion you actually fo not need a step-up
you can use 3.3V version of pro-mini with direct connection between VCC and lion
radio you can connect to lion using 3.3V LDO or 1-2 1n4148 connected simultaneously to drop voltage from 4.2 (fresh lion) bellow 3.6V (maximum allowed for radio)@axillent said:
radio you can connect to lion using 3.3V LDO or 1-2 1n4148 connected simultaneously to drop voltage from 4.2 (fresh lion) bellow 3.6V (maximum allowed for radio)
It's probably moot, but the diodes may drop substantially less voltage when the current is very low. Of course, there may be no harm done with such low currents - raising the current brings the Vfwd up too. I'm just noting that the "almost constant Vfwd" only applies to larger currents (eg: 10ma not 10 uA).
-
@axillent Looks good. But is not the LED symbol reversed in the schematics?
I am considering making a board as well for personal use (open HW of course), but using through hole components a bit more extensively for ease of customization. And probably a sockeded MCU so I don't have to include programming interfaces. In the future, I (and hopefully all of you) will push new FW to the board OTA so there will not be a need for holes in the case :)
But I might be interested to join in if your are ordering a batch of these as well. Will it be panelized and pick/placed as well?@Anticimex said:
In the future, I (and hopefully all of you) will push new FW to the board OTA so there will not be a need for holes in the case :)
For that, it's handy to have some extra flash on board. (Ref Moteino and anarduino)
-
@Anticimex said:
In the future, I (and hopefully all of you) will push new FW to the board OTA so there will not be a need for holes in the case :)
For that, it's handy to have some extra flash on board. (Ref Moteino and anarduino)
-
Yep, extra flash for OTA would be nice! Great idea for the next revision.
Would we need extra hardware for this?
If so what is your suggestion?Fulltime Servoy Developer
Parttime Moderator MySensors boardI use Domoticz as controller for Z-Wave and MySensors (previously Indigo and OpenHAB).
I have a FABtotum to print cases. -
@marceltrapman said:
Would we need extra hardware for this?
The flash downloader + flash code could be stored as a bootloader, but that would drop Arduino bootloader compatibility and it will be a challenge to get a stripped MySensors implementation in the bootloader area.
Maybe we can add a small i2c or spi eeprom which is used for temporary storage of the new firmware, but then again, how to get the image data from the eeprom into the ATMega's flash?
-
@ToSa is working on it.
https://github.com/ToSa27/BootloaderReports of successful OTA flash yesterday. But work still remain to make it safer. An extra eeprom would probably help safing things up a bit.
-
@ToSa is working on it.
https://github.com/ToSa27/BootloaderReports of successful OTA flash yesterday. But work still remain to make it safer. An extra eeprom would probably help safing things up a bit.
-
@ToSa is working on it.
https://github.com/ToSa27/BootloaderReports of successful OTA flash yesterday. But work still remain to make it safer. An extra eeprom would probably help safing things up a bit.
@hek said:
Reports of successful OTA flash yesterday.
Nice :)
But work still remain to make it safer. An extra eeprom would probably help safing things up a bit.
I have started my own board design so it would be very interesting for me to know where this is heading at. Any idea what would be preferred to use?
